################################################################################
# setup device defaults
################################################################################

  # The TARGET_CPU variable controls which processor should be targeted for
  # generated code.
   case ${TARGET_ARCH} in
      aarch64)
        TARGET_KERNEL_ARCH="arm64"
        TARGET_PATCH_ARCH="aarch64"
        TARGET_CPU="cortex-a55"
        TARGET_CPU_FLAGS="+crc+crypto+fp+simd"
        TARGET_FPU="fp-armv8"
	TARGET_FLOAT="hard"
        TARGET_FEATURES="64bit"
        ;;
      arm)
        TARGET_KERNEL_ARCH="arm64"
        TARGET_PATCH_ARCH="aarch64"
        TARGET_CPU="cortex-a55"
        TARGET_CPU_FLAGS="+crc"
        TARGET_FPU="neon-fp-armv8"
	TARGET_FLOAT="hard"
        TARGET_FEATURES="32bit"
        ;;
    esac

  # Kernel target
    DEVICE_NAME="RK3566"
    KERNEL_TARGET="Image"
    BOOTLOADER="u-boot"
    PARTITION_TABLE="gpt"
    UBOOT_LABEL="uboot"
    TRUST_LABEL="trust"
    DEVICE_DTB=("rk3566-evb2-lp4x-v10-linux")
    UBOOT_DTB="rk3566"
    UBOOT_CONFIG="rk3568_defconfig"
    PKG_SOC="rk356x"
    PKG_DATAFILE="${PKG_RKBIN}/bin/rk35/rk3566_ddr_1056MHz_v1.16.bin"
    PKG_LOADER="${PKG_RKBIN}/bin/rk35/rk356x_spl_v1.12.bin"
    PKG_BL31="${PKG_RKBIN}/bin/rk35/rk3568_bl31_v1.42.elf"
    PKG_LOAD_ADDR="0x0a100000"
    BOOT_INI=false
    EXT_LINUX_CONF=true

  # Additional kernel make parameters (for example to specify the u-boot loadaddress)
    KERNEL_MAKE_EXTRACMD=" $(for DTB in "${DEVICE_DTB[@]}"; do echo -n "rockchip/${DTB}.dtb "; done)"

  # Define the CPU
    HW_CPU="Rockchip RK3566"
 
  # Mali GPU family
    MALI_FAMILY="bifrost-g52"
    MALI_VERSION="g13p0"
    OPENGLES="libmali"
    VULKAN_SUPPORT="no"

    GRAPHIC_DRIVERS=""

  # Displayserver to use (weston / x11 / no)
    DISPLAYSERVER="no"

  # Windowmanager to use (fluxbox / weston / no)
    WINDOWMANAGER="no"

  # kernel serial console
    EXTRA_CMDLINE="quiet rootwait console=ttyUSB0,1500000 fbcon=rotate:1 console=tty0 ssh consoleblank=0 systemd.show_status=0 loglevel=0 panic=20"

  # additional packages to install
  #  ADDITIONAL_PACKAGES=""

  # additional Firmware to use (dvb-firmware, misc-firmware, wlan-firmware)
  # Space separated list is supported,
  # e.g. FIRMWARE="dvb-firmware misc-firmware wlan-firmware"
    FIRMWARE="RTL8821CS-firmware"

  # additional drivers to install:
  # for a list of additional drivers see packages/linux-drivers
  # Space separated list is supported,
  # e.g. ADDITIONAL_DRIVERS="DRIVER1 DRIVER2"
  #  ADDITIONAL_DRIVERS="RTL8821AU RTL8821CU RTL88x2BU"

  # build and install driver addons (yes / no)
    DRIVER_ADDONS_SUPPORT="no"
  
  # driver addons to install:
  # for a list of additinoal drivers see packages/linux-driver-addons
  # Space separated list is supported,
    DRIVER_ADDONS="" #dvb-latest

  # debug tty path
    DEBUG_TTY="/dev/ttyUSB0"

  # build and install bluetooth support (yes / no)
    BLUETOOTH_SUPPORT="yes"

  # build and install Avahi (Zeroconf) daemon (yes / no)
    AVAHI_DAEMON="no"

  # build with NFS support (mounting nfs shares via the OS) (yes / no)
    NFS_SUPPORT="no"

  # build with Samba Client support (mounting samba shares via the OS) (yes / no)
    SAMBA_SUPPORT="no"

  # build and install Samba Server (yes / no)
    SAMBA_SERVER="yes"

  # build and install SFTP Server (yes / no)
    SFTP_SERVER="yes"

  # build and install Simple HTTP Server (yes / no)
    SIMPLE_HTTP_SERVER="yes"

  # build and install OpenVPN support (yes / no)
    OPENVPN_SUPPORT="no"

  # build and install ZeroTier support (yes / no)
    ZEROTIER_SUPPORT="yes"

  # build and install diskmounter support (udevil)
  # this service provide auto mounting support for external drives in the
  # mediacenter also automount internally drives at boottime via udev (yes / no)
    UDEVIL="yes"

  # build and install exFAT fuse support (yes / no)
    EXFAT="yes"

  # build and install NTFS-3G fuse support (yes / no)
    NTFS3G="no"

  # build and install hfs filesystem utilities (yes / no)
    HFSTOOLS="no"

  # Support for partitioning and formating disks in initramfs (yes / no)
  # This adds support for parted and mkfs.ext3/4 to initramfs for OEM usage
    INITRAMFS_PARTED_SUPPORT="no"

  # build with swap support (yes / no)
    SWAP_SUPPORT="yes"

  # swap support enabled per default (yes / no)
    SWAP_ENABLED_DEFAULT="yes"

  # swapfile size if SWAP_SUPPORT=yes in MB
    SWAPFILESIZE="384"

  # Some devices have internal storage.
    INSTALLER_SUPPORT="yes"

  # cron support (yes / no)
    CRON_SUPPORT="no"

  # Settings package name - blank if not required
    DISTRO_PKG_SETTINGS=""

  # htop tool (yes / no)
    HTOP_TOOL="yes"
