Thanks to visit codestin.com
Credit goes to Github.com

Skip to content

Xinyuan-LilyGO/LilyGo-T-SIM7080G

BranchesTags

Repository files navigation

✨ LilyGO T-SIM7080G ✨

English | 中文

News

  • SIM7080G supports NB-IoT and Cat-M in global frequency bands, but does not support 2G/3G/4G. Please confirm that the SIM card used supports NB-IoT or Cat-M before use.
  • The SIM card must be inserted first before starting the SIM7080. If the SIM card is inserted after the SIM7080 is turned on, the modem will not be able to detect the SIM card.

1️⃣ Examples preview

examples 
├─AllFunction                       # Full function test example
├─ATDebug                           # AT Commands Example
├─BIGIOT_Gnss_Upload                # Upload positioning coordinates to BIGIOT IOT,Timed wake-up consumes about 1.2mA
├─BLE5_extended_scan                # Official BLE5 Example
├─BLE5_multi_advertising            # Official BLE5 Example
├─BLE5_periodic_advertising         # Official BLE5 Example    
├─BLE5_periodic_sync                # Official BLE5 Example
├─MinimalCameraExample              # Example of camera use
├─MinimalDeepSleepExample           # DeepSleep example
├─MinimalLowBattPowerExample        # Low Battery example
├─MinimalModemGPSExample            # SIM7080G GPS example
├─MinimalModemNBIOTExample          # SIM7080G NBIOT example
├─MinimalModemPowerSaveMode         # SIM7080G power maintenance example
├─MinimalModemSleepMode             # SIM7080G sleep example
├─MinimalModemAndEspSleep           # SIM7080G & ESP32 sleep example
├─MinimalModemUpgrade               # Upgrade SIM7080 built-in firmware
├─MinimalPowersCurrentExample       # Example of PMU charge current debug
├─MinimalPowersExample              # Example of PMU
├─MinimalSDCardExample              # Example of using SDCard
├─ModemFileUploadExample            # File Upload Example            
├─ModemMqttPublishExample           # MQTT Publish Example            
├─ModemMqttsAuthExample             # MQTTS Authentication Example    
├─ModemMqttsExample                 # MQTTS Example    
├─ModemMqttSubscribeExample         # MQTT Subscribe Example     
├─SIM7080G-ATT-NB-IOT-AWS-MQTT      # MQTTS AWS By @bootcampiot
├─SIM7080G-ATT-NB-IOT-HTTP-HTTPS    # HTTP/HTTPS  By @bootcampiot
└─SIM7080G-ATT-NB-IOT-SSL-Mosquitto # MQTTS Mosquitto By @bootcampiot

2️⃣ Quick Start

PlatformIO

  1. Install VisualStudioCode and Python
  2. Search for the PlatformIO plugin in the VisualStudioCode extension and install it.
  3. After the installation is complete, you need to restart VisualStudioCode
  4. After restarting VisualStudioCode, select File in the upper left corner of VisualStudioCode -> Open Folder -> select the LilyGo-T-SIM7080G directory
  5. Click on the platformio.ini file, and in the platformio column, cancel the sample line that needs to be used, please make sure that only one line is valid
  6. Click the (✔) symbol in the lower left corner to compile
  7. Connect the board to the computer USB
  8. Click (→) to upload firmware
  9. Click (plug symbol) to monitor serial output

ArduinoIDE

  1. Install ArduinoIDE
  2. Copy all the folders in the LilyGo-T-SIM7080G/lib directory to <C:\Users\UserName\Documents\Arduino\libraries>. If there is no libraries directory, please create a new one. Please note that you are not copying the lib directory, but copying the folders in the lib directory
  3. Open Arduino IDE -> Tools
  • Board -> ESP32S3 Dev Module
  • USB CDC On Boot -> Enable ## Note that you need to change Enable to Disable when USB is not connected, so USB CDC will not prevent the board from starting
  • CPU Frequency -> 240MHz
  • USB DFU On Boot -> Disable
  • Flash Mode -> QIO 80MHz
  • Flash Size -> 16MB(128Mb)
  • USB Firmware MSC On Boot -> Disable
  • PSRAM -> OPI PSRAM
  • Partition Scheme -> 16M Flash(3MB APP/9.9MB FATFS)
  • USB Mode -> Hardware CDC and JTAG
  • Upload Mode -> UART0/Hardware CDC
  • Upload Speed -> 921600
  1. Insert USB into the PC and click Upload <If the upload fails, see Tips>

Use reference

Product Youtube link explanation Status
T -7080G Youtube link How to update the firmware of SIM7080G series products ✅
LilyGo device Youtube link How to enter boot mode to download the firmware ✅

3️⃣ Tips

  1. T-SIM7080 has two USB ports, the USB-C port is used to upload sketches and Serial output, and Micro-USB is used for SIM7080G firmware version upgrade
  2. ⚠ SIM7080G cannot connect to cellular network and GPS positioning at the same time
  3. Board integrated PMU (Power management chip), with short circuit and overload protection. By default,PWRKEYneeds to be pressed for 6 seconds to turn off the board power supply, and pressPWRKEYfor 128 milliseconds to turn on the power supply. If you need to modify the power off pressing time, please refer toMinimalPowersExample
  4. If the charging function is required, thePMU TS Pindetection function needs to be turned off. By default, there is no NTC sensor on the board, so the TS Pin detection needs to be disabled before the charging function can be used normally. If theTS Pindetection function is not turned off, the PMU charging indicator will flash after the battery is inserted, and charging will be disabled
  5. The VSYS pin is the system path voltage of the PMU. The voltage of this pin is equal to the input voltage. The output of this pin is equal to the input voltage. If the input voltage source is USB-C, then this pin is the voltage of USB-C. If it is a battery, then this pin is the voltage of the battery.
  6. The DC5 power supply voltage can be adjusted, and the maximum output current should not exceed 1A
  7. DC1 is the core power supply voltage, and the default output is 3.3V. Please do not adjust the DC1 voltage through software
  8. When the sketch cannot be uploaded, please press and hold the BOOT button on the board, and then insert the USB. At this time, you should be able to see the port in the device manager of the computer, and then click Upload Sketch again
  9. When the power supply channel of the ESP32S3 is closed incorrectly, please insert USB, and then press and hold the BOOT button of the board, and then press and hold the PWRKEY button. At this time, the board enters the download mode, and the sketch can be uploaded normally
  10. If the power supply of the board cannot be turned on when the battery is connected, please check that the mechanical switch beside the USB is turned toON, and then press the board PWR for 2 seconds. At this time, the board should start to work
  11. The range of solar input voltage is 4.4~6V. Please select an appropriate solar panel and set the maximum charging current as 500mA
  12. If the camera is not connected, all IO ports are available. If the camera is used, the board has only GPIO45 and GPIO46 is idle
  13. T-SIM7080G uses Octal SPI PSRAM, so GPIO35~GPIO37 is unavailable. Please do not use these IOs
  14. ⚠ Please understand the risks to be faced before changing the voltage of peripherals, otherwise do not try to change the voltage of cameras and other on-board devices, which may cause permanent damage
  15. ⚠ Please do not turn off the BLDO1 power supply, otherwise ESP32S3 and SIM7080G cannot communicate normally
  16. Please check the Operating Instructions for updating the built-in firmware of the modem. Generally, upgrading the firmware is not recommended
  17. The board uses USB as the JTAG upload port. When printing serial port information on USB_CDC_ON_BOOT configuration needs to be turned on. If the port cannot be found when uploading the program or the USB has been used for other functions, the port does not appear. Please enter the upload mode manually.
    1. Connect the board via the USB cable
    2. Press and hold the BOOT button , While still pressing the BOOT button, press RST
    3. Release the RST
    4. Release the BOOT button
    5. Upload sketch
  18. If you encounter a problem that you cannot register a network, please refer to this issue#100

4️⃣ Where to buy:

  1. AliExpress
  2. LilyGo Store

5️⃣ Pins

Camera PWDN Reset XCLK SDA SCL VSYNC HREF PCLK
GPIO N/A 18 8 2 1 16 17 12
Camera D9 D8 D7 D6 D5 D4 D3 D2
GPIO 9 10 11 13 21 48 47 14
  • If you do not use a camera, you can freely allocate IO ports here. Assuming you need to allocate I2C, please use the display to call Wire and pass the required IO ports, such as 
    int sda = 13;  // You can also use other IO ports
int scl = 21;  // You can also use other IO ports
Wire.begin(sda,scl)
Modem PWR RXD TXD RI DTR
GPIO 41 4 5 3 42
PMU SDA SCL IRQ
GPIO 15 7 6
SDCard CMD CLK DATA
GPIO 39 38 40

6️⃣ Power domain

Modem Camera ESP32S3 SDCard Level conversion
DC3/BLDO2(GPS) ALDO1/ALDO2/ALDO4 DC1 ALDO3 BLDO1

7️⃣ Voltage range

Battery Voltage requirements Minimum Maximum Charging Current
SIM7080G 3.5V 4.2V Custom adjustment, maximum 1A
  • It is recommended to use flat top 18650 batteries with a capacity of more than 2500mA
Solar Voltage requirements Minimum Maximum Charging Current
SIM7080G 4.4V 6V 500mA

Tip

It is recommended to use a solar panel with an output voltage of 6V or 5V and a power of about 5-10W. Solar energy can only charge the battery. Without the battery, the panel cannot supply power. Please note that this is only a suggestion. It is not necessary to use a 5-10W solar panel. 1W is also acceptable. The size of the solar panel determines the current and speed of solar charging. Please note that depending on the environment, the sunshine time may not exceed one hour per day. At this time, if the solar panel is too small and the light is not sufficient, it cannot be charged.

8️⃣ ON-BOARD LED

FUNCTION COLOR
MODEM STATUS RED (Near the modem)
MODEM NETWORK STATE RED (Near the modem)
CHARGE LED BLUE (Controlled by PMU, default charging indicator)
  • The network status light can be turned off by command, please see the AT manual AT+CNETLIGHT command
  • Status light cannot be turned off

MODEM NETWORK STATE

Network light status Module working status
64ms on/ 800ms off When not registered on the network
64ms on/ 3000ms off Already registered on the network (PS domain registration successful)
64ms on/ 300ms off During data transmission (PPP dial-up state and when using internal TCP/FTP/HTTP and other data services)
Off Power off or PSM sleep mode

About

No description or website provided.

Topics

camera nbiot esp32s3 sim7080g axp2101

Resources

Readme
Activity
Custom properties

Stars

100 stars

Watchers

6 watching

Forks

48 forks
Report repository

Releases

No releases published

Packages

No packages published

Contributors 7

Languages